Пікірлер

• 
  @zephaudi2 күн бұрын

  are those intake manifold linkages stock 😅

• 
  @theexile46942 күн бұрын

  Don't drill the rivets. Jesus. Just disassemble the console and do a proper paint job. Lol.

• 
  @quietlion334 күн бұрын

  I have a no crank no start on a 2014 accent. It has new crank position sensor,new battery and new low fuel pump. What’s the first sign of bad starter?

• 
  @user-mp5oc3jf7y5 күн бұрын

  Hey quest do I need to remove the valve covers in order to get the intake out

• 
  @user-gx4fu9wq4x7 күн бұрын

  Hello man thanks for video I have a question about audi a8 d3, there are many mistake lights on control panel like as abs esp and big attention sign. But no sign of malfunction because car is move good, how can I fix and delete this mistakes and what should I do

• 
  @HassinahCotwal-zh2bm8 күн бұрын

  HI I NEED TO MAKE 4 PORT FEUL PRESSURE REGULATOR/DAMPER TUTORIAL

• 
  @ronaldpassanante9 күн бұрын

  No focus on the switch on the actuator

• 
  @stephaniebranham691410 күн бұрын

  Best educational video I’ve seen on that particular job on a 4.0. Thank you very much sir!!

• 
  @dannytorres629111 күн бұрын

  Useless ass video bro

• 
  @JB-xg7io22 күн бұрын

  Can you even buy that USC paint stripper anymore?

• 
  @santinonavarro485327 күн бұрын

  Is the hoses the same for the lbz2007

• 
  @dustyveilplaysАй бұрын

  bro great job but what accent is that?

• 
  @paulwaters6384Ай бұрын

  Great video, thanks a lot. I received two bags from China, it seems all the top seals are included. What are the set of keys you have at 5:43 to release the connector? Thanks again!

• 
  @joedalton5395Ай бұрын

  25:48 ok! Donc faire la distribution sans respecter la procédure, engendre une forte consommation de carburant !!! Big merci à toi mon frère ! Car j’ai, justement, une forte consommation d’essence. Et je vais y remédier grâce à toi🙏😉

• 
  @joedalton5395Ай бұрын

  10:35 clik clik clik au démarrage… c’est à cause du tendeur de chaînes d’arbres à cames !!! Ok ok. Merci beaucoup. Mais après avoir remplacé les tendeurs de chaînes d’arbres à cames, comment remettre les arbres à cames en place bien orienté? (bien caler, bien droit. Est-ce qu’il y à un repère, ou une encoche , Ou quelques choses pour indiquer le bon emplacement ?)

• 
  @SouthernDevilDog83Ай бұрын

  What's the paint color for the speaker grills? I want to repaint mines and your color is the same as mine

• 
  @daviddavis6231Ай бұрын

  There ias no need for any seel on the shaft , centifugal force of the spinning prevents any leakage along the shaft , I know what you are doing is well intentioned but it will not make the slightest difference . How do i know this; I am a time served heating engineer.

• 
  @davidsyked9420Ай бұрын

  This video is like some one goes to the repair shop have the work done and ask for the old parts and make a video and show no work (the car looks great)

• 
  @newrecruitmentway5686Ай бұрын

  I have the same snd woring done , but now become worest

• 
  @Swiss4.2Ай бұрын

  Is age or mileage more important when determining whether a timing belt is still good? My A8 only has 50k kms added since the timing belt was replaced but the belt was replaced but it was replaced almost 12 years ago. I'm going to be replacing the belt anyways just to be safe but what do you think?

• 
  @joedalton53952 ай бұрын

  Is the distribution the same, for the Audi 3.7l v8 2004 280hp please? (Clamping torce, same camshaft setting bar, pige ect...)

• 
  @joedalton53952 ай бұрын

  Est-ce que c’est pareil la distribution, pour la Audi 3.7l v8 2004 280ch svp? (Couple de serrage, même barre de calage arbres à cames, pige ect… )

• 
  @Veikra2 ай бұрын

  Oui, le 3.7L BFL de meme année partage presque que tout apart la cylindré.

• 
  @00019g2 ай бұрын

  Yeah what if the whole sides and roof part are completely gone rusted is it still possible to just cover everything in bondo and sand it and sculpt it to the original form? It would be hard as fuck because it has to be perfect for the door seals and the windshield gasket to fit

• 
  @Veikra2 ай бұрын

  No, it wouldnt hold. You need a donor frame to weld in there

• 
  @beaner_fromyuma8122 ай бұрын

  So your purge valve was leaking air into the system but had no fuel leaks ?

• 
  @Veikra2 ай бұрын

  yes, suction from injection pump would draw air in. I had no lift pump back then

• 
  @beaner_fromyuma8122 ай бұрын

  @@VeikraI’m running into issues with my truck, It’s was puffing clouds of white smoke threw in my scanner it showed misfire in cylinder 5, changed that one injector and it fixed it for a day now it’s back to puffing slight clouds under acceleration

• 
  @beaner_fromyuma8122 ай бұрын

  I’m no diesel mechanic but I understand what it needs to run

• 
  @beaner_fromyuma8122 ай бұрын

  I’ve been dreading on taking it to the shop because I know it’s going to cost me a arm and a leg for diagnosis

• 
  @beaner_fromyuma8122 ай бұрын

  And labor

• 
  @mslcars20112 ай бұрын

  Thank you ,, good job

• 
  @Veikra2 ай бұрын

  Welcome

• 
  @newrecruitmentway56862 ай бұрын

  I have issue at abs still even I make the wiring

• 
  @Veikra2 ай бұрын

  Post VCDS scan of abs module please

• 
  @reymendoza47772 ай бұрын

  Mine is throwing p0193 fuel rail pressure low during power enrichment, only does it while towing on a steep grade. Things I've done New cp3 Filter housing rebuild New fuel filter Ppe race plug New fuel lines inside engine bay Any help is appreciated please

• 
  @Veikra2 ай бұрын

  You have one or many injectors with a higher than normal return rate. Have the return rates tested, you'll see. Truck can run perfectly fine then fall flat the next second and that is exactly the code that will pop up. Procedure is simple, you unhook the return line and stuff them in a graduated cylinder for x amount of time. Look it up

• 
  @STOUTMANXXX2 ай бұрын

  That multi tool your using fives off the impression that you're a butcher. As if that wasnt bad enough i had to watch you slop glue all over the place. This review is for anyone thinking this work is the standard practice for this repair. Its not

• 
  @Veikra2 ай бұрын

  there is no pretension that this is a hack, as said in the video. I even say out loud i'll be replacing it later. But 7pm on a friday and the car show is already started. Aint no overnight parts from japan!

• 
  @Abukaled-dp3rr2 ай бұрын

  Bay weip saet address

• 
  @BadBoy-xn8jc2 ай бұрын

  How did you do that change on yours i have the same model and need to find out how to in stall them

• 
  @Veikra2 ай бұрын

  I dont know what else you need to know. The steps are explained in the video. You want to see the wrenches turning?

• 
  @NewLogiK2 ай бұрын

  I was on the fence about buying one. Thanks for confirming how good it is, I'll definitely get one !

• 
  @Veikra2 ай бұрын

  Wait, I"ll put my affiliate link in the description so you can buy it for "cheaper"

• 
  @mikep5092 ай бұрын

  from Quebec? Im just inspecting my 2009 toyota corrola for rust around the top of the roof near the windshield... my problem is my windshield is in good shape... pulling it out and putting it back is out of my skill set... i might need to get this done by a carrosie

• 
  @Veikra2 ай бұрын

  I'm in the greater Montreal area. You could get a glass professionnal to pull it and put it back.

• 
  @mikep5092 ай бұрын

  @@Veikra a mobile unit?... that would be the best bet... they come take it out, I fix the rust over a couple days, then they put it back... I was going to pass by a salvage yard and get a spare windshield if mine cracks for whatever reason...the Kenny Upull in LaPrarie has a 2010 corrolla there that I needed a part from that had a good windshield... to be continued 😁

• 
  @oaggie732 ай бұрын

  Do they smoke when driven at high temperature?

• 
  @Veikra2 ай бұрын

  what to you mean high temperature?

• 
  @oaggie732 ай бұрын

  @@Veikra Operating temp. Smoke coming out from underside. Havent figured out source yet

• 
  @tylersaunders33702 ай бұрын

  @@oaggie73mine is doing the same thing I still can’t figure it out but I definitely have fuel in my exhaust so it smokes as it warms up

• 
  @rasmusthrane79572 ай бұрын

  Does the A8 2008 4,2 gasoline also have belt?

• 
  @Veikra2 ай бұрын

  no, 2008 is a chain on the a8

• 
  @rasmusthrane79572 ай бұрын

  @@Veikra Ah ok.

• 
  @MoJo.262 ай бұрын

  What tools are needed for the job

• 
  @Veikra2 ай бұрын

  nothing fancy, torx bit in very small rachet required for some bolts

• 
  @patrickperry10792 ай бұрын

  Hey buddy my name is Patrick an I'm doing the same swap on my 03 Duramax an I would like to ask you a couple of questions if you don't mind I took the wires out of the doner harness that needed an installed them into my factory harness pin for pin the only wires i have left over that are not hooked up are a pink wire, yellow an brown with a white stripe that went to the doner harness at the left front kick panel plug do I need to splice them into my factory harness or are they not used also everything works other than my heated seats on both sides im not sure what to do any help would be much appreciated!

• 
  @Veikra2 ай бұрын

  hard to tell which wires those are. As I said in video, the color changes between model and years. For instance, my harness is avalanche instead of sierra so almost no colors. Can you make a video and show both harness? Its been years since I've done mine

• 
  @cihanergul11152 ай бұрын

  Hey man same problem here. Brake works just fine when I pull it and push it but somehow it beeps all the time as if it is still on while none of the brakes are active. Driving became hell and I am not able to go to a mechanic . I am thinking of cutting off the EPB fuses just so this annoyimg sound goes away. I dont need handbrakes either. What would you say?

• 
  @Veikra2 ай бұрын

  It`s a parking brake motor that froze. There is a bearing in there that can rust if the parking brake isnt used often. An D3 a8 will beep over 10 km/h for 1 minute straight. Then it if you go below 10, it will reset and it will beep another minute once you resume driving over 10km/h. If the motor is frozen, it will log a fault. Supply voltge for EPB motor either left or right I've opened and fixed those motors with 100% success rate but I have access to a lot of tools. It`s always the frozen bearing for lack of use, or the connector that got corroded. I would rather fix it that delete it. You will have more problems than you think deleting it. on the a8, the car mesures brake pad thickness with this motor. So you will have 2 permanents malfunction light flashing in your dash, with the beeps on startups, plus a brake pad worn message. Get a used caliper, remove the motor and replace yours, then cycle the parking brake 3 times. Done deal and you`ll only MAYBE need to set pad thickness

• 
  @TheRariza233 ай бұрын

  What did you use to cut

• 
  @Veikra3 ай бұрын

  x acto knive

• 
  @strelokblackburn46513 ай бұрын

  I thought the 4.2 had a timing chain, in the rear of the motor?

• 
  @Veikra3 ай бұрын

  4.2 is only the displacement. There is dozens of different 4.2 engine models. Some with belts, some with chains. All the newer ones are chain, though. The BFM and BGK of the audi a8 and a8l are some of the best v8 ever made.

• 
  @strelokblackburn46513 ай бұрын

  @Veikra I picked yp a 98 a6 with a 2.8 5v. 109k miles, everything but abs works...for now. Very well taken care of, doin timing belt, thromostat and valve cover gaskets next month

• 
  @TheBarrettrussell3 ай бұрын

  Thanks so much for posting these! Recently grabbed a 447 I'm about to tear into.

• 
  @Veikra3 ай бұрын

  I reconditionned a lot of 447 and 445. If you have any questions let me know.

• 
  @joelgarcia52413 ай бұрын

  What size of hose did you use ? My truck is having the same symptoms

• 
  @Veikra3 ай бұрын

  1/2 inch ID for feed. Returns are 3/8 ID

• 
  @user-sb2uh7ke9z3 ай бұрын

  Does anyone know what the purple and brown connection are for that go to the BCM and fuse panel? Just installed a donor harness that didn't have these but had factory heated seats. Wondering if all I need know is a factory door switch to turn the seats on? Do I need those two plugs for the heated seats to work? Any help is greatly appreciated.

• 
  @Veikra3 ай бұрын

  2003 and up do not require any door harness. The switch in the door connects to the window switch and uses the CANbus to talk to heated seat module

• 
  @user-sb2uh7ke9z3 ай бұрын

  @@Veikra do you know what the purple connection that went into the bottom of the BCM is for? Same with the brown connection that was with it that went to the fuse box on the side of the dash.

• 
  @user-sb2uh7ke9z3 ай бұрын

  @veikra, do you know if I need the purple and brown connection to get the heated seats to work? I bought a switch and it has power, but no orange lights for the heat. Thanks.

• 
  @user-sb2uh7ke9z2 ай бұрын

  I installed the harness out of a 03 into my 05. I bought the factory heated seat switch and connected it into my door switch. It has power just not the orange light for heat. Do I need a different BCM? Or do I need to reflash the one in the truck? Any help is much appreciated

• 
  @oldkicker89583 ай бұрын

  I make them out of old washers. Basically the same as you did. 👍

• 
  @Veikra3 ай бұрын

  good idea!

• 
  @farazsiddiqui66893 ай бұрын

  Thanks for this Veikra. Very helpful. What make of hub did you use? Is MOOG a dependable brand? I also have to replace the lower and upper arms. All bushing is shot. Thanks again.

• 
  @Veikra3 ай бұрын

  at least MOOG has a warranty. It's what I use. Always avoid cheap bearing, they arent worth it, and fail prematurely

• 
  @zephaudi4 ай бұрын

  Any tips on cv axle shield rounded out bolt???

• 
  @Veikra4 ай бұрын

  yes, aligne a large punch with a flat base. Needs to be perfectly flat on the head of the bolt. It will shrink it back. Otherwise cut the bolt, the treads are never stuck. You can also force a old torx inside of it, but you need a impact rated torx. Good luck

• 
  @zephaudi3 ай бұрын

  ​@@VeikraI managed to get it. Will be making crankshaft sensor video soon

• 
  @zephaudi4 ай бұрын

  Every upload makes me happy. There is rarely and video on a8 d3 gen in usa at least... thank you for providing these informations.

• 
  @victorl78114 ай бұрын

  Great video! Thanks for sharing!

• 
  @Veikra4 ай бұрын

  Thank you

• 
  @Veikra4 ай бұрын

  Update. I have now blown the new unit I got after this one. Same thing, the output shaft is wallowed out and moves sideway and ate the seal !

• 
  @sp33dweed4 ай бұрын

  hey dude is there anything to look out for when replacing the entire motor with a new one?

• 
  @Veikra4 ай бұрын

  Not on the a8. It will self calibrate as the a8 motor is a torque sensing unit.

• 
  @billymingo15184 ай бұрын

  Hey man I have the same compressor and I’m trying to change the valves do you no if there is 4 bigger valves and 3 smaller valves ?

• 
  @Veikra4 ай бұрын

  no. There is 5 big, 2 small ones. Some look different because you see the other side. You can get disks made of spring steel and reassemble them.

• 
  @billymingo15184 ай бұрын

  Do you no where I can find a manual for it ?

• 
  @billymingo15183 ай бұрын

  @@Veikrado you have an email or phone number ? I would like to talk to you i have some questions about my compressor