Flawed design, an anchor should be strong and stay fast in any direction in which it may be pulled upon. 🤷🏼♂️ this anchor hardware needs further refinement. The idea of turning the bed bolt location in to a dual purpose feature is very handy though. 🫡
@jhon548915 күн бұрын
@nicholaschase980 pointed out I had the L track tie downs mounted wrong, putting them in right they are rock solid 360 degrees.
@nicholaschase98015 күн бұрын
John, nice video. Just a couple obersvatoins. With the L-track fitting you need to turn the fitting so its snaps into place. The way you have them now will just pop out under a load. When they snap into place, it doesn't matter what position the OneTrax is in, the load can be at any angle relative to the anchor. Additionally, the bolts are TP50 (Torx Plus) instead of T50. Torx Plus has different dimensions and geometry and is rated for higher torque loads.
@jhon548915 күн бұрын
Thank you! Apparently I too struggle with following instructions.
@zac2112Ай бұрын
Great video! I have one of the gas blocks as well although I pin gauged the port around .063. Seems like the sizing for these has changed over the years. Heard from a couple people the port used to be around .052. Where did you grab yours from?
@diegocadenas17782 ай бұрын
How do magpul m3 pmag fit on the jack?
@ZzBiohazzardzZ2 ай бұрын
I think it’s one of those things appearance wise that’ll grow on you as you gain appreciation for its superb functionality. Wondering how this would pair on a hk417. How do you like it on your sig?
@danielsenthomas55012 ай бұрын
Is your gun a Taurus G3 and what model is your Safari holster? I’m trying to find one. Please tell me thank you
@user-vh8ce2yr5c2 ай бұрын
Polish made a very high quality weapons.
@TheWonderfulWonders4 ай бұрын
Sand it Down
@xDOOM954 ай бұрын
Whats the round count now
@jhon54894 ай бұрын
Roughly 2000 rounds and not a hiccup at all.
@killaronjones39334 ай бұрын
dat WBP woodstock smell
@thomasnelson78694 ай бұрын
I have the TA11 and I’m considering stepping it up.
@jaymike14 ай бұрын
Surefire x300. Problem solved
@jhon54894 ай бұрын
That's one way to do it, however the TLR-1HL is arguably the most prolific light in law enforcement due to it's high performance and low cost. This issue is more the result of duty holster manufacturers trying to build one holster to accommodate both lights.
@kmonroe57855 ай бұрын
I think it’s the retention screw with the rubber bushing on the side of the holster
@BShin5 ай бұрын
Hi sir, what mount plate do you use for your aim point acro for your m&p 2.0?
@jhon54895 ай бұрын
This model is factory milled for the ACRO. I would recommend you go with Forward Controls Design for an ACRO plate for your M&P. I've used their plates on Glocks and SIGs and they are very high quality. Another option that is a little cheaper is the OEM Aimpoint plate, which is made by B&T. I've not used a B&T plate, however they are known to be good quality and made out of steel. Those are the only two plates I would consider using.
@itzcuzzy38075 ай бұрын
Thanks!!!!
@Hellebarde13515 ай бұрын
Doesn’t the acog block the view of the rmr?
@jhon54895 ай бұрын
It does not.
@_-Brandon-_5 ай бұрын
Awesome video!!
@socaljarhead76706 ай бұрын
I’ve always wanted one. I know I’m in the minority.
@alanmeyers3957Ай бұрын
You won’t look through a clearer 6x anything and the field of view is superb, I think it’s the size that puts people off, I’ve got one on an aero m5.
@nohandle746 ай бұрын
It looks comical
@jhon54896 ай бұрын
Almost as comical as mounting a football to your rifle!
@alanmeyers3957Ай бұрын
Clearest scope on earth in that power range, bright at night, huge field of view, if they could shrink it…..
@Julius.3.6.915 күн бұрын
r u jealous mate? I think you are one of these tactical cool looking guys? ;) by the way very good review, I am considering to buy one.
@hovolo886 ай бұрын
Does the mastermount fit this?
@jhon54896 ай бұрын
Yes!! Also recommend RS Regulate mounts. This rifle has the standard AKM rail on the side.
@kygent5087 ай бұрын
Have a 556 on order.
@kygent5087 ай бұрын
What sling was that as I have the rifle on order.
@lennylemens7 ай бұрын
When I see a man charge the gun with his left hand I subscribe automatically.
@dougshelton698 ай бұрын
Got the 556 sl with 90° gasblock..looks like ak12...WBP does great job...check out there factory set up..state of the art cnc machining🇺🇸❤
@AtrociousAK479 ай бұрын
just picked up mine from my dealer a few days ago, red stock version with the rail, 7.62x39, ordered it through Arms of America since AFA said they couldnt ship it to my home state of jersey, as it was not compliant due to having both a threaded barrel and bayonet lug in addition to the pistol grip, though some folks on reddit say I couldve emailed them to ask em to "unlock" it for me. The thing with the mag is consistent with their stated policy, which says they wont do any sort of pinning or compliance work on the mag nor swapouts as they say there are too many state and local laws to keep track of and they cant be bothered dealing with it, and will simply ship it without a mag in the event the 30 rounders arent legal where you are, conversely, AOA will either pin it themselves for a little extra, remove it upon request, or ship it as is for your dealer to figure out, I chose to remove it as I didnt want the plastic mag, ended up ordering some polish steel surplus mags and had them pin em for me. she is a beauty, wood seems sorta cheap and almost resembles plastic but I think it still looks good and it feels nice enough in the hand, grip interestingly is smooth wood unlike the textured plastic one shown here, dont really care tho since I will be swapping that out for a rubber hogue, and the buttstock also doesnt have the trapdoor for the cleaning kit. The recoil is a bit harsher than I expected, atleast compared to my yugo sks, but then again this shouldnt be that surprising as it's a much lighter gun being a stamped reciever with a shorter barrel, and also that slant break probably doesnt help matters much either, trigger feels pretty nice too. Also kinda found the bolt and carrier tricky to reinsert with the dust cover, kinda prefer my sks in that regard, with that tilting bolt and seperate gas piston (sks is short stroke, ak is long stroke with a rotating bolt) I find are much simpler. already ordered a few upgrades for it such as the enhanced safety lever and mag release, really hoping I can do that myself and wont have to have my dealer install it. I was gonna have my dealer put a nice titanium mini comp from slr rifle works on it but it would seem they sent me one for the wrong caliber, as the threading is too big and would require a sleave of some kind be used with it, unfortunately it seems that by the time the gun arrived at my dealer I was already past the 30 day refund window, and they didnt respond to my email inquiry about it, so probably gonna opt for some other model from some other seller or brand even.
@UpinsmokeSmokey11 ай бұрын
Are they reliable?
@jhon548910 ай бұрын
Not a single issue with a variety of mags and a variety of import ammo (Tulammo, Arsenal, and rebranded Vympel)
@UpinsmokeSmokey10 ай бұрын
@@jhon5489thank you for the info … I’m thinking of getting one. They look really nice. But didn’t know how reliable they are .
@huRlrnd3lders11 ай бұрын
Fit and finish is amazing on those. I have built several AKs and don't see a huge deal with the bolt carrier peening. The most that will happen is that it gets stuck in the rear trunion. Easy fix. File the peened material. It should stop peening eventually. A hard trigger can break, BTW. Another thing that is not really a thing is the bolt carrier getting stuck on the hammer. Usually more noticeable on a new rifle. We don't have all the fun parts in our guns. The hammer rides a little higher. You can remove some material from forged parts to make it smoother (don't try with case hardened AR parts). Great video, I don't think I have complaints about the rifle at all. The mount is questionable. I think a solid opinion on it will come in time and after putting it through some stress. Thanks
@MatiasRodriguez611 ай бұрын
Cual es la medida de el cañon ???
@SS-tr5ru Жыл бұрын
10 round mags?
@DREKOWICK69 Жыл бұрын
i think I want one of these lol
@jhon5489 Жыл бұрын
Do it! Best AKM pattern rifle you can buy at any price right now.
@DREKOWICK69 Жыл бұрын
@@jhon5489 so if I had a chance of buying a KR103 for 949$, this is still the better firearm to get?
@jhon5489 Жыл бұрын
@@DREKOWICK69 in my opinion, yes the Jack is the better rifle. The barrel and important parts are all Polish military spec parts. The included piston is a cheap US part, but easy enough to change. What the KR103 does have is the option for a side folding stock.
@anegg1458 ай бұрын
@@DREKOWICK69Indeed it is a much higher quality AK. KUSA can barely build a functional AK that doesn’t blow up and that’s not a very high bar that is set. Their firing pins snap prematurely, yes they are billet but the trunions were heat treated by a blind alcoholic and end up softer than a baby’s ass cheeks so they end up going through accelerated wear cycles that would make even the top .1% of OnlyFans models jealous, light primer strikes due to the BCG being out spec and they slowly lose headspace due to again the soft ass trunions. I’m pretty sure the weakest Soylent drinking goy could strike primers harder than KUSA AKs. Not to even mention the QC is non-existent on them like a father who went out for milk and cigarettes since they are too busy arguing with people on their Instagram page instead of taking the valid criticism and build the rifle correctly. The price point they charge is wayyyy too high for what you get. There’s so many better options out there on the market that provide better value for your money like the WBP Jack rifles this fine gentlemen has and they recently started importing the Beryl Archer which is the modern Polish AK their army uses for $1500 which you can get on Arms of America or Atlantic Firearms. Hope I helped!!!
@ChanChan-gq6hq Жыл бұрын
The way of your speak and display is boring.
@officedullard8722 Жыл бұрын
Most gorgeous AK available. My only gripe is the black pistol grip. Really wish it was matching/semi-matching color to the wood. Yeah, can get a replacement grip, but I like it when things are kept simple.
@jhon5489 Жыл бұрын
Agreed. The USA made paint brush handle grip sucks big time. I switched to a Polish Bakelite and really enjoy it now.
@don-fuego9 ай бұрын
Is that normal? I just got mine yesterday and it came with a wood handle.
@officedullard87229 ай бұрын
If you get the Polish Laminate, you get the black polymer. If you get any of the other colors (like sunburst), you get all wood.
@AtrociousAK479 ай бұрын
@@officedullard8722 indeed, I got the red one, my grip is all wood, got mine from Arms of America tho, but i guess that isnt the reason.
@deejaytrizay Жыл бұрын
Holy Diverrr
@JahsosaGz Жыл бұрын
BAGAY sayo
@JahsosaGz Жыл бұрын
PANG taLbos Lyn Lyn
@JahsosaGz Жыл бұрын
LYN O"
@realisrealite5554 Жыл бұрын
Get a mount that's adjustable like Rs regulate
@jhon5489 Жыл бұрын
Running one now though it was more to get the optic lower than it was to add adjustability.
@silentstryker1590 Жыл бұрын
Looks good
@micahputman3374 Жыл бұрын
Good video, I think the mistake being made is the false sense on every LEO being an expert with firearms. I am not bashing LEO's at all but almost everyone in the Firearms community has encountered at least 1 Leo who made you step back and scratch your head and think "WTH?". I have seen some really sketchy and scary actions at ranges, and have even had heated debates with some for their handling procedures. The common factor between all were they had this opinion they were and expert due to being in law enforcement.
@nathanielmiller9941 Жыл бұрын
How do go about ordering one? How much and what website?
@jhon5489 Жыл бұрын
Arms of America or Atlantic Firearms. They have a relationship and pricing is identical. My experience with Atlantic was really good. As far as the process it's relatively simple. You'll need to find a local FFL if you don't already have one and then the seller will need a copy of their license for the log book. Once your FFL receives it just need to do the typical 4473 and background check.
@847lifestyle Жыл бұрын
so this one has the durable piston made in polish since it has the american stock right?
@jhon5489 Жыл бұрын
This one has the pretty low quality USA made piston. It's probably the only ding on this gun. It's already getting a little ugly with just shy of 1k through it.
@khunmg-cz7cu Жыл бұрын
တလံုးဘယ္ေလာက္
@POPJack1717 Жыл бұрын
PMAG doesn't belong in a classic AK.
@chinov9445 Жыл бұрын
Got the fox great AKs I change the cheap shepherds hook 🪝 put a BD2 muzzle break ATI pistol grip n a ALG trigger I do this to all my AKs in my collection just makes them even better shooters 🎯🤙🏽
@isaiahsoucy7793 Жыл бұрын
How was the mag wobble with different mags?
@jhon5489 Жыл бұрын
Polish painted surplus, new production Bulgarian steels, Arsenal waffle mags, and AC Unity are pretty much the right combination of easy to rock and lock but minimal wobble. Some of my clapped out surplus steels are loose, some tight.
@D_S_88 Жыл бұрын
Just bought the tiger stripe maple jack from atlantic. Can't wait to get my hands on it.
@danny-uu8hc Жыл бұрын
You change the front handgaurd wood? The stock wood that comes with it seems better than what you put on there. Love my Jack, too.
@hairydogstail Жыл бұрын
Great review, to the point and informative..
@jhon5489 Жыл бұрын
Thank you! I need to get the rifle it's on out to the range to test.
@jzamka3512 Жыл бұрын
Cho e xin sô dien thoa di ma a gui cho e sộ dien thoa cua a nhe
Пікірлер
Thank you.
Flawed design, an anchor should be strong and stay fast in any direction in which it may be pulled upon. 🤷🏼♂️ this anchor hardware needs further refinement. The idea of turning the bed bolt location in to a dual purpose feature is very handy though. 🫡
@nicholaschase980 pointed out I had the L track tie downs mounted wrong, putting them in right they are rock solid 360 degrees.
John, nice video. Just a couple obersvatoins. With the L-track fitting you need to turn the fitting so its snaps into place. The way you have them now will just pop out under a load. When they snap into place, it doesn't matter what position the OneTrax is in, the load can be at any angle relative to the anchor. Additionally, the bolts are TP50 (Torx Plus) instead of T50. Torx Plus has different dimensions and geometry and is rated for higher torque loads.
Thank you! Apparently I too struggle with following instructions.
Great video! I have one of the gas blocks as well although I pin gauged the port around .063. Seems like the sizing for these has changed over the years. Heard from a couple people the port used to be around .052. Where did you grab yours from?
How do magpul m3 pmag fit on the jack?
I think it’s one of those things appearance wise that’ll grow on you as you gain appreciation for its superb functionality. Wondering how this would pair on a hk417. How do you like it on your sig?
Is your gun a Taurus G3 and what model is your Safari holster? I’m trying to find one. Please tell me thank you
Polish made a very high quality weapons.
Sand it Down
Whats the round count now
Roughly 2000 rounds and not a hiccup at all.
dat WBP woodstock smell
I have the TA11 and I’m considering stepping it up.
Surefire x300. Problem solved
That's one way to do it, however the TLR-1HL is arguably the most prolific light in law enforcement due to it's high performance and low cost. This issue is more the result of duty holster manufacturers trying to build one holster to accommodate both lights.
I think it’s the retention screw with the rubber bushing on the side of the holster
Hi sir, what mount plate do you use for your aim point acro for your m&p 2.0?
This model is factory milled for the ACRO. I would recommend you go with Forward Controls Design for an ACRO plate for your M&P. I've used their plates on Glocks and SIGs and they are very high quality. Another option that is a little cheaper is the OEM Aimpoint plate, which is made by B&T. I've not used a B&T plate, however they are known to be good quality and made out of steel. Those are the only two plates I would consider using.
Thanks!!!!
Doesn’t the acog block the view of the rmr?
It does not.
Awesome video!!
I’ve always wanted one. I know I’m in the minority.
You won’t look through a clearer 6x anything and the field of view is superb, I think it’s the size that puts people off, I’ve got one on an aero m5.
It looks comical
Almost as comical as mounting a football to your rifle!
Clearest scope on earth in that power range, bright at night, huge field of view, if they could shrink it…..
r u jealous mate? I think you are one of these tactical cool looking guys? ;) by the way very good review, I am considering to buy one.
Does the mastermount fit this?
Yes!! Also recommend RS Regulate mounts. This rifle has the standard AKM rail on the side.
Have a 556 on order.
What sling was that as I have the rifle on order.
When I see a man charge the gun with his left hand I subscribe automatically.
Got the 556 sl with 90° gasblock..looks like ak12...WBP does great job...check out there factory set up..state of the art cnc machining🇺🇸❤
just picked up mine from my dealer a few days ago, red stock version with the rail, 7.62x39, ordered it through Arms of America since AFA said they couldnt ship it to my home state of jersey, as it was not compliant due to having both a threaded barrel and bayonet lug in addition to the pistol grip, though some folks on reddit say I couldve emailed them to ask em to "unlock" it for me. The thing with the mag is consistent with their stated policy, which says they wont do any sort of pinning or compliance work on the mag nor swapouts as they say there are too many state and local laws to keep track of and they cant be bothered dealing with it, and will simply ship it without a mag in the event the 30 rounders arent legal where you are, conversely, AOA will either pin it themselves for a little extra, remove it upon request, or ship it as is for your dealer to figure out, I chose to remove it as I didnt want the plastic mag, ended up ordering some polish steel surplus mags and had them pin em for me. she is a beauty, wood seems sorta cheap and almost resembles plastic but I think it still looks good and it feels nice enough in the hand, grip interestingly is smooth wood unlike the textured plastic one shown here, dont really care tho since I will be swapping that out for a rubber hogue, and the buttstock also doesnt have the trapdoor for the cleaning kit. The recoil is a bit harsher than I expected, atleast compared to my yugo sks, but then again this shouldnt be that surprising as it's a much lighter gun being a stamped reciever with a shorter barrel, and also that slant break probably doesnt help matters much either, trigger feels pretty nice too. Also kinda found the bolt and carrier tricky to reinsert with the dust cover, kinda prefer my sks in that regard, with that tilting bolt and seperate gas piston (sks is short stroke, ak is long stroke with a rotating bolt) I find are much simpler. already ordered a few upgrades for it such as the enhanced safety lever and mag release, really hoping I can do that myself and wont have to have my dealer install it. I was gonna have my dealer put a nice titanium mini comp from slr rifle works on it but it would seem they sent me one for the wrong caliber, as the threading is too big and would require a sleave of some kind be used with it, unfortunately it seems that by the time the gun arrived at my dealer I was already past the 30 day refund window, and they didnt respond to my email inquiry about it, so probably gonna opt for some other model from some other seller or brand even.
Are they reliable?
Not a single issue with a variety of mags and a variety of import ammo (Tulammo, Arsenal, and rebranded Vympel)
@@jhon5489thank you for the info … I’m thinking of getting one. They look really nice. But didn’t know how reliable they are .
Fit and finish is amazing on those. I have built several AKs and don't see a huge deal with the bolt carrier peening. The most that will happen is that it gets stuck in the rear trunion. Easy fix. File the peened material. It should stop peening eventually. A hard trigger can break, BTW. Another thing that is not really a thing is the bolt carrier getting stuck on the hammer. Usually more noticeable on a new rifle. We don't have all the fun parts in our guns. The hammer rides a little higher. You can remove some material from forged parts to make it smoother (don't try with case hardened AR parts). Great video, I don't think I have complaints about the rifle at all. The mount is questionable. I think a solid opinion on it will come in time and after putting it through some stress. Thanks
Cual es la medida de el cañon ???
10 round mags?
i think I want one of these lol
Do it! Best AKM pattern rifle you can buy at any price right now.
@@jhon5489 so if I had a chance of buying a KR103 for 949$, this is still the better firearm to get?
@@DREKOWICK69 in my opinion, yes the Jack is the better rifle. The barrel and important parts are all Polish military spec parts. The included piston is a cheap US part, but easy enough to change. What the KR103 does have is the option for a side folding stock.
@@DREKOWICK69Indeed it is a much higher quality AK. KUSA can barely build a functional AK that doesn’t blow up and that’s not a very high bar that is set. Their firing pins snap prematurely, yes they are billet but the trunions were heat treated by a blind alcoholic and end up softer than a baby’s ass cheeks so they end up going through accelerated wear cycles that would make even the top .1% of OnlyFans models jealous, light primer strikes due to the BCG being out spec and they slowly lose headspace due to again the soft ass trunions. I’m pretty sure the weakest Soylent drinking goy could strike primers harder than KUSA AKs. Not to even mention the QC is non-existent on them like a father who went out for milk and cigarettes since they are too busy arguing with people on their Instagram page instead of taking the valid criticism and build the rifle correctly. The price point they charge is wayyyy too high for what you get. There’s so many better options out there on the market that provide better value for your money like the WBP Jack rifles this fine gentlemen has and they recently started importing the Beryl Archer which is the modern Polish AK their army uses for $1500 which you can get on Arms of America or Atlantic Firearms. Hope I helped!!!
The way of your speak and display is boring.
Most gorgeous AK available. My only gripe is the black pistol grip. Really wish it was matching/semi-matching color to the wood. Yeah, can get a replacement grip, but I like it when things are kept simple.
Agreed. The USA made paint brush handle grip sucks big time. I switched to a Polish Bakelite and really enjoy it now.
Is that normal? I just got mine yesterday and it came with a wood handle.
If you get the Polish Laminate, you get the black polymer. If you get any of the other colors (like sunburst), you get all wood.
@@officedullard8722 indeed, I got the red one, my grip is all wood, got mine from Arms of America tho, but i guess that isnt the reason.
Holy Diverrr
BAGAY sayo
PANG taLbos Lyn Lyn
LYN O"
Get a mount that's adjustable like Rs regulate
Running one now though it was more to get the optic lower than it was to add adjustability.
Looks good
Good video, I think the mistake being made is the false sense on every LEO being an expert with firearms. I am not bashing LEO's at all but almost everyone in the Firearms community has encountered at least 1 Leo who made you step back and scratch your head and think "WTH?". I have seen some really sketchy and scary actions at ranges, and have even had heated debates with some for their handling procedures. The common factor between all were they had this opinion they were and expert due to being in law enforcement.
How do go about ordering one? How much and what website?
Arms of America or Atlantic Firearms. They have a relationship and pricing is identical. My experience with Atlantic was really good. As far as the process it's relatively simple. You'll need to find a local FFL if you don't already have one and then the seller will need a copy of their license for the log book. Once your FFL receives it just need to do the typical 4473 and background check.
so this one has the durable piston made in polish since it has the american stock right?
This one has the pretty low quality USA made piston. It's probably the only ding on this gun. It's already getting a little ugly with just shy of 1k through it.
တလံုးဘယ္ေလာက္
PMAG doesn't belong in a classic AK.
Got the fox great AKs I change the cheap shepherds hook 🪝 put a BD2 muzzle break ATI pistol grip n a ALG trigger I do this to all my AKs in my collection just makes them even better shooters 🎯🤙🏽
How was the mag wobble with different mags?
Polish painted surplus, new production Bulgarian steels, Arsenal waffle mags, and AC Unity are pretty much the right combination of easy to rock and lock but minimal wobble. Some of my clapped out surplus steels are loose, some tight.
Just bought the tiger stripe maple jack from atlantic. Can't wait to get my hands on it.
You change the front handgaurd wood? The stock wood that comes with it seems better than what you put on there. Love my Jack, too.
Great review, to the point and informative..
Thank you! I need to get the rifle it's on out to the range to test.
Cho e xin sô dien thoa di ma a gui cho e sộ dien thoa cua a nhe