Пікірлер

• 
  @blogodome4 ай бұрын

  Продолжай! Отлично получается

• 
  @onehandedmaker5 ай бұрын

  I like it! Kind of modern and kind of reto I think? Loved the vibe of your video and have subscribed. Regards James One Handed Maker - Australia

• 
  @pmacc35576 ай бұрын

  Very nice 👍

• 
  @retrocow Жыл бұрын

  How has this video only got 500 views over 3 years? It's this type of craftwork and attention to detail that should be getting all the attention! Not to mention all the videography, setup time, editing involved. I'm just starting out on my woodworking journey and really appreciate video's like this. I've just kitted out my workshop and recently also bought a steiner lathe and cannot wait to just keep creating and get my work and skillset to this level.

• 
  @cirderf12 Жыл бұрын

  Hi! Great work and nice design. How did you remove the screw holes after turning the seat on the lathe?

• 
  @w9jim Жыл бұрын

  Very nice video. I wish I had learned the wood lathe as part of my carpentry skills.

• 
  @maikwouters2415 Жыл бұрын

  Nice flag in your shop

• 
  @spartanfx3028 Жыл бұрын

  Great video....can you please tell me what that green spinning machine is called?

• 
  @NorthSummitStudio Жыл бұрын

  Thanks! That’s called a lathe.

• 
  @maikwouters24152 жыл бұрын

  Nice video mate, i picked up some tips i am going to use building my own round table this summer

• 
  @NorthSummitStudio2 жыл бұрын

  Awesome! Glad it was some help, thanks for watching✌️

• 
  @alvaroricardobavaresco29942 жыл бұрын

  Beautiful work. Very clean. What finish did you use?

• 
  @NorthSummitStudio2 жыл бұрын

  Thanks ! I think I used General Finishes Arm-R-Seal on this one, but not honestly I don’t completely remember 😅

• 
  @johncummins32542 жыл бұрын

  I think this would have been a much better video if you had explained how you locate the seat holes, what angles you cut them out, and what glue you are using. I assume it is some type of hide glue. I for one am not a fan of KZread videos that don't give you all the information you need to make a project. It just wastes time.

• 
  @NorthSummitStudio2 жыл бұрын

  Thanks for the suggestion John, definitely see where your coming from. Stilling finding the balance of what is used to show and what will just bore people to death 😅. I’ve toyed around with making separate videos that explain the details a bit more to fill I. The gaps. And yup I use Old Brown hide glue.

• 
  @johncummins32542 жыл бұрын

  @@NorthSummitStudio I didn't think I would get a reply so thanks. I have seen a number of videos that do not have an audio description of the process but have screen comments that fill in the blanks. Perhaps this might be a happy medium. By the way I did like the quality of your finished products. John

• 
  @NorthSummitStudio2 жыл бұрын

  @@johncummins3254 that’s not a bad idea, we’ll see what comes in the future, if I actually make another video…maybe this will give me a reason to get my butt in gear, Thanks!

• 
  @robertcornelius35142 жыл бұрын

  Nice work, but that seat probably needs to be a half inch thicker. Old books show thin seats only good for plant stands.

• 
  @NorthSummitStudio2 жыл бұрын

  Not sure what constitutes as a “thin seat”these are around a 1 1/4” thick and have held up for years just fine. It would have to be a pretty hefty load to compromise a piece of wood that thick. Thanks for watching ✌️

• 
  @robertcornelius35142 жыл бұрын

  @@NorthSummitStudio , have ya been to Walmart lately? Ha

• 
  @NorthSummitStudio2 жыл бұрын

  @@robertcornelius3514 obviously, where else would I go for furniture design ideas?

• 
  @gunkarlsson37792 жыл бұрын

  Apart from the incredible woodworking, the editing and music choice is so good. Really soothing to watch, wouldn't mind to see even longer or more detailed videos. Hope you keep making these, much appreciated!

• 
  @rafaelg74222 жыл бұрын

  Muy bonita felicidades

• 
  @carmelinakatzman18633 жыл бұрын

  I think I'll do it myself this week. I just got instructions from Woodprix and I'm ready for it: D

• 
  @diygeneration55663 жыл бұрын

  That's a great chair you got there, and your tools are great. I have videos on my channel about stools too. It is nice to meet a colleague. Friends?

• 
  @brandyhawking79083 жыл бұрын

  Hmmm... I finally followed Ann's advice and took Woodglut. It's great for beginners and has some advanced stuff too.

• 
  @nicholasrosalez85353 жыл бұрын

  I hope you still make videos and respond to this but Dude love the style does it have a certain name? And can you tell me how you angle the seat to drill the holes? And what angles did you use on the 2 same and 1 offset leg?

• 
  @NorthSummitStudio3 жыл бұрын

  Hey thanks so much Nicholas, the seats are at 78 degrees, all the legs are actually drilled at the same angle one just looks off set depending on what angle you look at the stool. To drill them I just made a jig that really just an auxiliary table set to the 78 degree angle and put in the drill press. Also not sure the style , kind of a modern shaker maybe?? Anyway hope this helps and thanks for watching ✌️

• 
  @gregorymosher50083 жыл бұрын

  How do you make the circle cutting jig on the bandsaw? And what finish did you rub in? Nice video!

• 
  @NorthSummitStudio3 жыл бұрын

  The finish is Osmo Polyx Satin. The circle jig is just a rail that runs in a groove running perpendicular to the blade in a piece of plywood. The rail has a nail sticking out of the end, mark your center on and place it in the mail. Slide the piece closer to the blade until you reach your desired size and spin the piece until your circle is completely cut out. It’s hard to explain but I’m sure you can find a video on how to make one somewhere in KZread. But maybe that’s a future video idea. Thanks for watching!

• 
  @cheekuu263 жыл бұрын

  Clean project

• 
  @NorthSummitStudio3 жыл бұрын

  Thanks so much my friend. 🙏

• 
  @westonstaheli56633 жыл бұрын

  Was that a home-made finish you used?

• 
  @NorthSummitStudio3 жыл бұрын

  Not home made at all just Osmo Polyx clear satin

• 
  @chadryk53 жыл бұрын

  Nice work man! Question: What angle are you drilling your legs at?

• 
  @NorthSummitStudio3 жыл бұрын

  Thanks so much my friend! I actually have no clue so I checked it when I got into the shop and it’s about 73 degrees. I made the jig for the angled mortises a long while ago so never remember 😅. Thanks for watching!

• 
  @invictu4488 Жыл бұрын

  ​@@NorthSummitStudio was wondering about the angle as well... 😅

• 
  @jacquesfarouche79623 жыл бұрын

  What tool is he using at 00:42?

• 
  @NorthSummitStudio3 жыл бұрын

  Hey Jacques, that's a circle cutting jig I made for the bandsaw. Hope that helps!

• 
  @jacquesfarouche79623 жыл бұрын

  @@NorthSummitStudio yeah thank you!

• 
  @Sapoguapo3 жыл бұрын

  Definitely want to see more from you. Beautiful stuff!

• 
  @NorthSummitStudio3 жыл бұрын

  Thanks so much. Trying to fit in video making more and more but not always easy. 😊

• 
  @user-wo3yk5fj4k3 жыл бұрын

  when you have an electrical planner and you also use your hand planner only for youtube to show craftsmanship.ridiculous

• 
  @NorthSummitStudio3 жыл бұрын

  Omg you caught me ! You’re totally right, it’s not at all because the machine doesn’t leave a glue ready surface so I clean it up with a hand plane and make sure it’s still square, probably not that at all......also it’s a jointer, not a planer, or a planner. But thanks for coming I today 😘

• 
  @jodymontez6933 жыл бұрын

  Figuring out legs angles? Yea geomotry major I'm not. Beautiful job. Sometimes it's just nice to watch.🌲🌳

• 
  @NorthSummitStudio3 жыл бұрын

  Thanks Jody! I'm definitely not a geometry major either but I honestly just hold up a leg to a seat that isn't drilled out yet and see what looks good. There were a few iterations that didn't come out so great and when in doubt just check out a stool or chair you like and go from there.

• 
  @MartinMMeiss-mj6li3 жыл бұрын

  Very pretty stool, and a nice video too.

• 
  @NorthSummitStudio3 жыл бұрын

  Thanks Martin!

• 
  @gigithompson55453 жыл бұрын

  are the measurements for the legs or the height

• 
  @NorthSummitStudio3 жыл бұрын

  This table was 20" tall and top is 17" in diameter. Thanks!

• 
  @gigithompson55453 жыл бұрын

  @@NorthSummitStudio thank you

• 
  @doraduo53883 жыл бұрын

  This is helpful! I read that you need to naturalize the bleached piece with 50/50 white vinegars and water. Do you think it’s necessary? Also, have you compared bleaching vs. whitewash stain? I’m debating between those two and seeking for some professional suggestions. Thank you!

• 
  @NorthSummitStudio3 жыл бұрын

  Dora Duo thanks! I’ve never neutralized the bleach at all, I’ve heard the same but from what I know you don’t have to with this product which is Lite-N-Up from Wood Kote. I haven’t done a comparison with the white stain but I think if you want a true bone white finish bleach and then the white finish would be the way to go. The bleach gets it 90% the way there and the white oil brings it all the way. Hope this helps!

• 
  @ibaunited3 жыл бұрын

  Hi I have a few questions. How did you make holes for the angled legs? Where did you fit the brass pegs? And what’s the angle of the legs?

• 
  @garzonlaperle94034 жыл бұрын

  I heard about woodprix good opinions.

• 
  @chrisperry26364 жыл бұрын

  Hope you keep making these. Nice to see videos out of more legit shops like yours.

• 
  @NorthSummitStudio4 жыл бұрын

  Thanks so much Chris much appreciated 🙏

• 
  @zumkellerwoodshop42244 жыл бұрын

  Great video! You make that look really easy and I'm pretty certain its not. Also, I love that zoom in/zoom out transition before you put the blank on the lathe! Very nice!

• 
  @NorthSummitStudio4 жыл бұрын

  Thanks so much man. This one was pretty simple but fun. Haha that’s the only fancy transition I know or at least remember how to do 😅

• 
  @salvatoreboutilette50204 жыл бұрын

  where can I get directions on hot build this? with angle measurements etc

• 
  @NorthSummitStudio4 жыл бұрын

  There are no directions for this really ,if there was a demand for it it’s possible I’d make some plans though.

• 
  @dominicferro83144 жыл бұрын

  This is absolutely beautiful. Definitely do more videos

• 
  @NorthSummitStudio4 жыл бұрын

  Thank you, I will!

• 
  @PY-ne5oh4 жыл бұрын

  Nice minimalist design. Nice execution.

• 
  @NorthSummitStudio4 жыл бұрын

  P Y thank you so much, it is much appreciated 🙏

• 
  @zumkellerwoodshop42244 жыл бұрын

  So calming! Nice vid👍

• 
  @NorthSummitStudio4 жыл бұрын

  Zumkeller Woodshop thanks Brotha! I got rid of the longer version , thought this one was a little more watchable. ✌️

• 
  @timothyhall13774 жыл бұрын

  Nice looking stool. Good job with your first video. Continued success.

• 
  @NorthSummitStudio4 жыл бұрын

  timothy hall thanks Timothy! I’ll be coming out with some more videos one the very near futures, thanks for watching 🤟🏻

• 
  @zumkellerwoodshop42244 жыл бұрын

  You need to do more videos! This is awesome!!👍

• 
  @NorthSummitStudio4 жыл бұрын

  Zumkeller Woodshop thanks man! This year I’m going to be making more videos so stay tuned

• 
  @jerrystark35874 жыл бұрын

  A very nice stool with a straightforward and well-crafted design. I offer no suggestions, but I do offer one thought: If you drill a larger hole (about 3/8" to 1/2" deep) the size of the leg diameter where it joins the seat and then drill a through hole on the same center, for the tenon,then the leg just below the tenon will sit a bit inside the stool seat and not show any of the tenon. This can be a nice touch, adding to a somewhat cleaner design, if it interests you. Is it necessary? Of course not. Again, great stool and an interesting video. Best of luck!

• 
  @NorthSummitStudio4 жыл бұрын

  Thanks so much Jerry! I've actually done that technique on a bar height version of this stool just to add a little more rigidity. But I actually do like the way it looks when you leave the tenon exposed a bit rather than hiding it. I agree though, definitely gives a little cleaner more seamless look. Thanks for watching! ✌️

• 
  @peternewton48064 жыл бұрын

  Made my own stool based on your design and very pleased with the result. Many thanks for your video. May I ask - what is the diameter and thickness of the seat (before turning)?

• 
  @Chris-sz7hz4 жыл бұрын

  Peter thanks so much man! I try to keep the seat blanks to 1-1/4" thick befor turning. Send me some pictures I'd love to see it. [email protected]

• 
  @koreanwoodworker25824 жыл бұрын

  Nice work. Thank you for sharing it!

• 
  @danilolopes76835 жыл бұрын

  DANILO

• 
  @volkerpetersen22685 жыл бұрын

  Very nice video! I was in doubt whether it takes a special Forstner bit to drill at an angle :) Well, not anymore, seems slight angles can be done in a drill press. All important steps shown, a very nice "no nonsense" video. Only thing, looking at 5:08 at the dimensions, feels like the legs could have been a bit more slender in the middle. Could be the angle of the photo though. Would like to see more of your work! Please make a bench in similar style :)

• 
  @NorthSummitStudio5 жыл бұрын

  Thanks so much for the feedback! Yeah the angle is shallow enough where the point of the forstner bit still hits the wood first. Its definitely possible to go a little more slender on the leg but to keep a cigar-like taper would make the bottom more slender, I would just be hesitant due to where the stretcher is mortised into the leg you loose a lot of wood in the leg so it might weaken the leg. I hope to make some more videos soon, tough to get done among commissions, thanks for stopping by!

• 
  @andrewmccarn5 жыл бұрын

  Will definitely be making a tool rest like you have when turning the legs. That would be PERFECT for turning rolling pins. I get so tired of moving the tool rest around when making those. lol Great video man, need to post more!

• 
  @Chris-sz7hz5 жыл бұрын

  Thanks so much man, yeah I definitely need to post more, my problem is I'll film a bunch and then be close to finished and stop filming because I just want to get it done haha. But yeah that long tool rest is a game changer, really easy to make but makes your work flow so much better.

• 
  @maxselber82265 жыл бұрын

  Thanks for sharing your work, very enjoyable to watch! Makes me want to built one myself. Have you ever tried "regular" hide glue (beads), that "brown glue" stuff seems rather pricey.

• 
  @Chris-sz7hz5 жыл бұрын

  Thanks so much Max! I haven't tried the beads but I've been meaning to and yeah the Old Brown Glue is definitely a bit pricey but I guess you're paying for the convenience. The beads seem like a little bit of an initial investment, I'll probably take the leap eventually because I do really like using hide glue for a lot of things.

• 
  @Hiksan55 жыл бұрын

  Great lookign chair and a lovely video. Enjoyed the music and the execution. Thank you for sharing! Subscribed

• 
  @Chris-sz7hz5 жыл бұрын

  Thanks so much Ty, much appreciated!

• 
  @snovskypolovsky6 жыл бұрын

  Nice work, enjoyed that one...

• 
  @NorthSummitStudio6 жыл бұрын

  snovskypolovsky thanks! Enjoyed making it so will be making some more soon. 👍