You don’t have too but Teflon really helps when you take it apart a year later. Without the corrosion on the threads are so bad you can not unscrew it
@istra70Ай бұрын
I also displaced rubber plug in carburetor when accidentally created pressure in fuel tank... Easy fix.
@istra70Ай бұрын
My 3.5 runs perfectly ! And i used to drive it hard all day long .... The only time i was careful was at the beginning when I was running it in....
@DungeonbeatzАй бұрын
Hank is that you 🤣
@MyUnquenchableThirstАй бұрын
Thanks for the tips!
@ArabiaBayRidgeАй бұрын
It does not have a size listed on it or it has worn off I think I emailed turbo and bought the one they recommended
@nswaveАй бұрын
what size turbo swing i have same motor
@Stripe12Ай бұрын
So did it make a difference??
@ArabiaBayRidgeАй бұрын
Yes I changed the fitting and trimmed the vent plug no problems in years now
@ryanharrod11552 ай бұрын
You got a video on how you installed that steel guide?
@ArabiaBayRidgeАй бұрын
I don’t. 1/2 inch aluminum rod from Lowe’s welded to a 1/8 inch aluminum plate hand bent the rod cut to fit with a jig saw bolted to skeg and attached to shaft with hose clamps. Has never moved
@ArabiaBayRidge3 ай бұрын
Nothing to do with data the transducer throws a lot of spray on my outboard without
@colin52303 ай бұрын
What is the point of these? Does it do anything for ypur data its collecting? Or is it just to prevent it from spraying?
@cd11689 ай бұрын
You didn’t show shit
@pokeygalaxy10 ай бұрын
this video sucks
@jameslakes501910 ай бұрын
As much cost should out perform great out box😊
@edwincordero181011 ай бұрын
Thanks I have that problem yesterday with my sea hunt
@JuanHernandez-jc6re Жыл бұрын
What shaft length you recommend ?
@steve880311 ай бұрын
@JuanHernandez-jc6re it depends on the boat and the mount height. You want the propeller to be about 12" in the water.
@gmoneyfilmss Жыл бұрын
i just got a trolling motor for my john boat and have a question is there a right and wrong for mounting your motor rear or bow?? from what i’ve researched what motor you have determines your mounting position, but am curious if there’s a reason other than that?? thank you!!
@SpinachMinich Жыл бұрын
You takin dale, bill, and boomhauer out later?
@ArabiaBayRidge Жыл бұрын
I now have about 220 hrs on the unit. No issues at I change the fluid every year just because it is easy I did have the lower repainted because it was peeling
@dillongoble7483 Жыл бұрын
Hey I'm here seeking the same answers did you ever have any problems with the lower unit? I have a lot of metal shavings in mine.
@ArabiaBayRidge Жыл бұрын
I now have about 670 hrs total on the boat and I think about 220 hrs or so on the new lower unit No problems at at. I change the fluid every year just because it is easy. I now have a power tech prop and the gear shifting is a lot quieter than a solas prop
@JamesJoseph-te3jm Жыл бұрын
I was getting so pissed, how do they expect you to remove it without doing this! there is absolutely no room to do it, glad you posted this, i would have been screwed, thank you.
@WillInWestPalm Жыл бұрын
yamahaw
@ArabiaBayRidge Жыл бұрын
That’s right … you wanna fight about it 🤣 lol. I got a southern draw
@TheFilthyOX Жыл бұрын
Thanks for this video. My tiller is shearing the bolts on the top gearbox and broke the top brace as well. Now I am thinking nothing is holding the bottom of the gearbox as there are no heads on those bolts or they fell out. Time to start investigating.
@joshuaculick7767 Жыл бұрын
What battery to use on it ?
@josephcampise6441 Жыл бұрын
I use a 12 deep cycle marine battery on mine
@josephcampise6441 Жыл бұрын
12v*
@ArabiaBayRidge Жыл бұрын
12 volt deep cycle. I have used a agm 27 series and now have a lithium 60ah all 12 volt for this model
@zachgray319 Жыл бұрын
Is that the tranducer 3m plate? How it holding up?
@ArabiaBayRidge Жыл бұрын
Yes the splash plate and the 3m plastic mount are still doing great
@ArabiaBayRidge3 ай бұрын
3m mount is still doing great!!
@Htownrule Жыл бұрын
I have a way older version on my 12ft Jon Boat it’s the Motorguide Brute 750 45lbs trust version.. I was wondering has this one held up well for you and do you recommend me upgrading?
@miketexas4549 Жыл бұрын
Hank Hill?
@ArabiaBayRidge Жыл бұрын
No I’m his smarter cousin
@jasonhollis8700 Жыл бұрын
This was a smart $20 fix instead of a $200 prop puller. Thank you for posting this video.
@matt4887 Жыл бұрын
Thanks very helpful
@jasonwade6184 Жыл бұрын
I've lost the little rubber stopper What is its purpose
@ndk8111 Жыл бұрын
Question - when you removed your prop did the forward thrust hub came off easily (the yellow round plate the prop sits on)? My 60hp mercury 2022 prop came off but the hub seems like ceased to the shaft - it should be coming off easily, no? I too was thinking of pulling like you instead of trying to bang it. So if you could provide additional details I would appreciate. Also, did you have to use penetrating oil / liquid wrench at all?
@ArabiaBayRidge Жыл бұрын
I did not use oil. And my thrust washer was loose I would suggest a wire wheel on a drill clean the shaft good soak with penetrating oil and tap lightly
@travonnjohnson5606 Жыл бұрын
Thank you!!! This is exactly what is wrong with mine. I'm new to this, so I would have never noticed. This helps a lot!!!
@ahmedbatt3662 жыл бұрын
Hi, how is the result after installing the shield so far? I have the same issue with the same transducer.
@ArabiaBayRidge2 жыл бұрын
It works! Water no longer hits my outboard or sprays high I can still see water spray but this greatly reduced my problem I would buy it again
@JohnSmith-xq6cv2 жыл бұрын
For sale?
@JohnSmith-xq6cv2 жыл бұрын
Is it easy without row markers?
@jimfrits3342 жыл бұрын
Thanks, you just saved me a lot of trouble. I have three seals on their way to me as I type this.
@cameronbuck3345 Жыл бұрын
Where did you order the seals from?
@michaelsolis26742 жыл бұрын
Yep needed that...
@ezzyeggy2 жыл бұрын
Do you have to loosen the motor or front case to get it off?
@ArabiaBayRidge2 жыл бұрын
You do not have to move the motor or front differential The prop will slide back enough once you remove the roll pin
@jimquantic2 жыл бұрын
This IS superior to the way I just did it, it really is because it pulls it true--straight out. But my method worked and without the rigging. I used a rubber hammer--I know, sounds bad, but bear with me. I "tapped" pretty gently as I rotated the prop, each wrap is of course off-set, so as I said, not ideal. But after maybe 50 or less raps, I saw it break free from the seal it had made, then I pulled it straight off.
@kippiemoore74392 жыл бұрын
Now how do you put it back together?
@slugzgaming51583 жыл бұрын
Horrible audio no idea what u said
@scottm64493 жыл бұрын
Nice job explaining the gearbox removal. Had similar seal leak with the pto shaft on my Tarter 5 ft. tiller. Used 00 grease and 85-140 gear oil and it worked until the seal popped out. Removed the pto shaft from the tractor tapped the seal back in and it now does not leak. Please check your your gearcase filler/breather fitting to be certain it is open. Let my tiller sit for a year and when I checked the chaincase fill level plug it was still under a great deal of pressure and it shot out some gear oil! That much pressure could cause a leak or pop a seal maybe, Thanks!
@robertleibold45023 жыл бұрын
I am having a heck of a time right now getting that bottom piece on the plunger to unscrew All rusted up and now I have it in my electrolysis bucket. Most likely will have to order a new plunger too... :(
@ArabiaBayRidge3 жыл бұрын
I tried several penetrating sprays and even heat and could not separate the plunger. I had buy a new one after breaking the old
@ArabiaBayRidge3 жыл бұрын
Now I put Teflon tape on every set of threads to help prevent it
@0n3_0bs33 жыл бұрын
Got a how to to make this?
@ArabiaBayRidge3 жыл бұрын
I used a jigsaw with a metal blade to cut the aluminum in the shape you see in the video then I drilled two holes and bolted it on. I bought a flat piece of alumyat the hardware store
@ArabiaBayRidge3 жыл бұрын
Still have this on my outboard works great August 2020
@omieyouknowme3 жыл бұрын
Update on this, I'd like to duplicate on my tohatsu 6hp got tired of pulling weeds yesterday every 10 min
@ArabiaBayRidge3 жыл бұрын
You won’t be sorry for adding one. The drilled holes also help a lot for the water pump to continue to pump while weeds are wrapped on side of skeg
@skyrimking40984 жыл бұрын
This doesnt show how to remove it... you already removed it!!!!!
@tylerw14184 жыл бұрын
That’s a cool idea! I’d buy one for my 5 hp
@ArabiaBayRidge4 жыл бұрын
Just take jig saw with a metal blade and cut a small piece of aluminum. You can buy aluminum squares at lowes
@tylerw14184 жыл бұрын
ArabiaBayRidge might do that. Thanks buddy
@joewintrick63704 жыл бұрын
Where did you find a replacement fuel hose, I’m having no luck??
@ArabiaBayRidge4 жыл бұрын
The tohatsu dealer in my area had it. It is clearly just a length of marine fuel line that he cut to length off a spool and and replaced. I'm guessing you could order some the same diameter from westmarine or amazon
@ArabiaBayRidge4 жыл бұрын
I was ready to throw this motor away ... then a short piece of hose and it runs great now for over a year.
@tzevetrelos4 ай бұрын
I have problem with tohatsu 3.5 hp 4 stroke 2012. What model do you have?
Пікірлер
Carbed 4 strokes are trash
I didn't know you use Teflon tape
You don’t have too but Teflon really helps when you take it apart a year later. Without the corrosion on the threads are so bad you can not unscrew it
I also displaced rubber plug in carburetor when accidentally created pressure in fuel tank... Easy fix.
My 3.5 runs perfectly ! And i used to drive it hard all day long .... The only time i was careful was at the beginning when I was running it in....
Hank is that you 🤣
Thanks for the tips!
It does not have a size listed on it or it has worn off I think I emailed turbo and bought the one they recommended
what size turbo swing i have same motor
So did it make a difference??
Yes I changed the fitting and trimmed the vent plug no problems in years now
You got a video on how you installed that steel guide?
I don’t. 1/2 inch aluminum rod from Lowe’s welded to a 1/8 inch aluminum plate hand bent the rod cut to fit with a jig saw bolted to skeg and attached to shaft with hose clamps. Has never moved
Nothing to do with data the transducer throws a lot of spray on my outboard without
What is the point of these? Does it do anything for ypur data its collecting? Or is it just to prevent it from spraying?
You didn’t show shit
this video sucks
As much cost should out perform great out box😊
Thanks I have that problem yesterday with my sea hunt
What shaft length you recommend ?
@JuanHernandez-jc6re it depends on the boat and the mount height. You want the propeller to be about 12" in the water.
i just got a trolling motor for my john boat and have a question is there a right and wrong for mounting your motor rear or bow?? from what i’ve researched what motor you have determines your mounting position, but am curious if there’s a reason other than that?? thank you!!
You takin dale, bill, and boomhauer out later?
I now have about 220 hrs on the unit. No issues at I change the fluid every year just because it is easy I did have the lower repainted because it was peeling
Hey I'm here seeking the same answers did you ever have any problems with the lower unit? I have a lot of metal shavings in mine.
I now have about 670 hrs total on the boat and I think about 220 hrs or so on the new lower unit No problems at at. I change the fluid every year just because it is easy. I now have a power tech prop and the gear shifting is a lot quieter than a solas prop
I was getting so pissed, how do they expect you to remove it without doing this! there is absolutely no room to do it, glad you posted this, i would have been screwed, thank you.
yamahaw
That’s right … you wanna fight about it 🤣 lol. I got a southern draw
Thanks for this video. My tiller is shearing the bolts on the top gearbox and broke the top brace as well. Now I am thinking nothing is holding the bottom of the gearbox as there are no heads on those bolts or they fell out. Time to start investigating.
What battery to use on it ?
I use a 12 deep cycle marine battery on mine
12v*
12 volt deep cycle. I have used a agm 27 series and now have a lithium 60ah all 12 volt for this model
Is that the tranducer 3m plate? How it holding up?
Yes the splash plate and the 3m plastic mount are still doing great
3m mount is still doing great!!
I have a way older version on my 12ft Jon Boat it’s the Motorguide Brute 750 45lbs trust version.. I was wondering has this one held up well for you and do you recommend me upgrading?
Hank Hill?
No I’m his smarter cousin
This was a smart $20 fix instead of a $200 prop puller. Thank you for posting this video.
Thanks very helpful
I've lost the little rubber stopper What is its purpose
Question - when you removed your prop did the forward thrust hub came off easily (the yellow round plate the prop sits on)? My 60hp mercury 2022 prop came off but the hub seems like ceased to the shaft - it should be coming off easily, no? I too was thinking of pulling like you instead of trying to bang it. So if you could provide additional details I would appreciate. Also, did you have to use penetrating oil / liquid wrench at all?
I did not use oil. And my thrust washer was loose I would suggest a wire wheel on a drill clean the shaft good soak with penetrating oil and tap lightly
Thank you!!! This is exactly what is wrong with mine. I'm new to this, so I would have never noticed. This helps a lot!!!
Hi, how is the result after installing the shield so far? I have the same issue with the same transducer.
It works! Water no longer hits my outboard or sprays high I can still see water spray but this greatly reduced my problem I would buy it again
For sale?
Is it easy without row markers?
Thanks, you just saved me a lot of trouble. I have three seals on their way to me as I type this.
Where did you order the seals from?
Yep needed that...
Do you have to loosen the motor or front case to get it off?
You do not have to move the motor or front differential The prop will slide back enough once you remove the roll pin
This IS superior to the way I just did it, it really is because it pulls it true--straight out. But my method worked and without the rigging. I used a rubber hammer--I know, sounds bad, but bear with me. I "tapped" pretty gently as I rotated the prop, each wrap is of course off-set, so as I said, not ideal. But after maybe 50 or less raps, I saw it break free from the seal it had made, then I pulled it straight off.
Now how do you put it back together?
Horrible audio no idea what u said
Nice job explaining the gearbox removal. Had similar seal leak with the pto shaft on my Tarter 5 ft. tiller. Used 00 grease and 85-140 gear oil and it worked until the seal popped out. Removed the pto shaft from the tractor tapped the seal back in and it now does not leak. Please check your your gearcase filler/breather fitting to be certain it is open. Let my tiller sit for a year and when I checked the chaincase fill level plug it was still under a great deal of pressure and it shot out some gear oil! That much pressure could cause a leak or pop a seal maybe, Thanks!
I am having a heck of a time right now getting that bottom piece on the plunger to unscrew All rusted up and now I have it in my electrolysis bucket. Most likely will have to order a new plunger too... :(
I tried several penetrating sprays and even heat and could not separate the plunger. I had buy a new one after breaking the old
Now I put Teflon tape on every set of threads to help prevent it
Got a how to to make this?
I used a jigsaw with a metal blade to cut the aluminum in the shape you see in the video then I drilled two holes and bolted it on. I bought a flat piece of alumyat the hardware store
Still have this on my outboard works great August 2020
Update on this, I'd like to duplicate on my tohatsu 6hp got tired of pulling weeds yesterday every 10 min
You won’t be sorry for adding one. The drilled holes also help a lot for the water pump to continue to pump while weeds are wrapped on side of skeg
This doesnt show how to remove it... you already removed it!!!!!
That’s a cool idea! I’d buy one for my 5 hp
Just take jig saw with a metal blade and cut a small piece of aluminum. You can buy aluminum squares at lowes
ArabiaBayRidge might do that. Thanks buddy
Where did you find a replacement fuel hose, I’m having no luck??
The tohatsu dealer in my area had it. It is clearly just a length of marine fuel line that he cut to length off a spool and and replaced. I'm guessing you could order some the same diameter from westmarine or amazon
I was ready to throw this motor away ... then a short piece of hose and it runs great now for over a year.
I have problem with tohatsu 3.5 hp 4 stroke 2012. What model do you have?