so i did this and my dish washer still doesnt start
@InfinityFishing Жыл бұрын
great video !
@traceytillson3289 Жыл бұрын
Thanks!
@spencerjameson9076 Жыл бұрын
Very helpful!!
@andysat13182 жыл бұрын
Thanks for the video.
@faizamaqsood12372 жыл бұрын
Very help full viedoo
@mdkhalil33212 жыл бұрын
Vera good vaudares
@turquoisecat7612 жыл бұрын
pointless without sound arseholes
@phillipbridge50092 жыл бұрын
They usually want you to buy the whole hose for one silly solenoid....this video is GREAT
@Crazytown2 жыл бұрын
Nice. I need to do this with a Flavel Finesse 100. I hope it is the same procedure
@stephenclaypool93842 жыл бұрын
I replaced a thermostat in a gas range
@stephenclaypool93842 жыл бұрын
How to replace a thermostat in a gas range but instead of taking the top completely off I bent the thermostat to get it through the hole, then straightened it out, any info on that procedure, does that defect the stat?
@davidjordorson98522 жыл бұрын
Posted 6 years ago and that's the only comment . Brilliant lol love it
@deisreebelle12063 жыл бұрын
My oven was not heating just like the unit on video.where can we buy oven thermostat?
@antarmshaw2 жыл бұрын
EBay
@evosagan28773 жыл бұрын
video is fine but no audio
@davidwilkinson33293 жыл бұрын
Excellent video
@AlistairBremen3 жыл бұрын
Wtf is that?!
@spirosgal1885 Жыл бұрын
Type 88 water inlet valve. Siemens and Bosch
@stevekelly51663 жыл бұрын
People are going to think they need a powered screwdriver! A great way to crossthread or strip theads. A tip to others, when you swap the wires, do it one at a time onto the new switch, then swap the switches over. Don't just pull them all off and hope for the best. Another tip, take a photo so you know what it looked like - just in case.
@jds1vette3 жыл бұрын
Nice
@DamianMooruth4 жыл бұрын
And yet ANOTHER video that skips oit actually fitting the seal.... Its a 3 man job!! Is there anyone out there that has a video showing how to actually fot it back on
@gordonkay62853 жыл бұрын
did you find any?
@HansWorstenbroodje3 жыл бұрын
@@gordonkay6285 I need answers...
@passtheparcel20242 жыл бұрын
Roy's the boy: kzread.info/dash/bejne/hoipxNqhc5eokaw.html
@tuppybrill49152 жыл бұрын
I had to take the front off my AEG. Also rub cooking oil round the seal where it will clip on the drum
@elizander34 жыл бұрын
WTF?
@t-mansam75824 жыл бұрын
They don't often go bad but when it does you need some professional instruction... Thanks a lot for this video
@no1jrb5 жыл бұрын
prolly better with commentary .....
@karimabdullah29256 жыл бұрын
Hi, happened to come across your video after watching soo many repair videos. Only yours matches with the shaft assembly on the back of my condenser dryer. It looks very similar. My dryer is a Haier HDY-D70 condenser dryer and the there's a squealing noise coming from the drum shaft area. I'm not sure how to replace the bearing and can't source the shaft. I can source the bearing. Will the bearing be located on the outside casing of the dryer just like in your video? Will i just be able to easily only replace the bearing or will i have to take the entire dryer apart to replace the shaft as well?? Thanks
@karimabdullah29256 жыл бұрын
many thanks for the video. I was able to locate the bearing at the back which was exactly in the same location as shown in the dryer in your video. You're the man.
@shantellamend89867 жыл бұрын
you can do it yourself ,just go to inplix page and learn how to make it.
@romanamerlene85548 жыл бұрын
I made it too. Want to know how ? just go to inplix webpage.
Пікірлер
so i did this and my dish washer still doesnt start
great video !
Thanks!
Very helpful!!
Thanks for the video.
Very help full viedoo
Vera good vaudares
pointless without sound arseholes
They usually want you to buy the whole hose for one silly solenoid....this video is GREAT
Nice. I need to do this with a Flavel Finesse 100. I hope it is the same procedure
I replaced a thermostat in a gas range
How to replace a thermostat in a gas range but instead of taking the top completely off I bent the thermostat to get it through the hole, then straightened it out, any info on that procedure, does that defect the stat?
Posted 6 years ago and that's the only comment . Brilliant lol love it
My oven was not heating just like the unit on video.where can we buy oven thermostat?
EBay
video is fine but no audio
Excellent video
Wtf is that?!
Type 88 water inlet valve. Siemens and Bosch
People are going to think they need a powered screwdriver! A great way to crossthread or strip theads. A tip to others, when you swap the wires, do it one at a time onto the new switch, then swap the switches over. Don't just pull them all off and hope for the best. Another tip, take a photo so you know what it looked like - just in case.
Nice
And yet ANOTHER video that skips oit actually fitting the seal.... Its a 3 man job!! Is there anyone out there that has a video showing how to actually fot it back on
did you find any?
@@gordonkay6285 I need answers...
Roy's the boy: kzread.info/dash/bejne/hoipxNqhc5eokaw.html
I had to take the front off my AEG. Also rub cooking oil round the seal where it will clip on the drum
WTF?
They don't often go bad but when it does you need some professional instruction... Thanks a lot for this video
prolly better with commentary .....
Hi, happened to come across your video after watching soo many repair videos. Only yours matches with the shaft assembly on the back of my condenser dryer. It looks very similar. My dryer is a Haier HDY-D70 condenser dryer and the there's a squealing noise coming from the drum shaft area. I'm not sure how to replace the bearing and can't source the shaft. I can source the bearing. Will the bearing be located on the outside casing of the dryer just like in your video? Will i just be able to easily only replace the bearing or will i have to take the entire dryer apart to replace the shaft as well?? Thanks
many thanks for the video. I was able to locate the bearing at the back which was exactly in the same location as shown in the dryer in your video. You're the man.
you can do it yourself ,just go to inplix page and learn how to make it.
I made it too. Want to know how ? just go to inplix webpage.