Пікірлер

• 
  @mfauzanbadrani51645 күн бұрын

  What is the rpm of the pump?

• 
  @kitronik3 күн бұрын

  Hi, this information is not available from the manufacturers as they express speed for pumps in flow rate. These pumps have a flow rate of 1 - 3L/min, depending on the supply voltage. I hope this helps.

• 
  @chriswilfrid7 күн бұрын

  If 10cm thickness still transparent

• 
  @nani598713 күн бұрын

  Maximum oTemperature of liquid that can be handled by this pump please

• 
  @RKELLEHER4014 күн бұрын

  Howdy, Brother! What resistor should I use if I have a yellow 10mm LED Emitting Diode (1.8-2.2V) powered by two AA Batteries? I will have an on/off switch in the loop. Will 47 ohms work? i tried 100 ohm resistor but the batteries were getting hot. I'm not even sure if I asked the question properly . Thanks for any assistance.

• 
  @kitronik13 күн бұрын

  Hi, and thanks for the question. If it's a standard LED then 47 ohms should be perfect for the job. We have a pretty cool calculator on our website that can be used for this. Select the LED you have from the dropdown list and then use the button to pull through the details. Add your supply voltage and then hit the calculate button. I hope this helps; kitronik.co.uk/blogs/resources/led-resistor-value-calculator

• 
  @RKELLEHER4012 күн бұрын

  @@kitronik Thank you, Brother! By the way, your LED Resistor Value Calculator is fantastic. Nice work!!

• 
  @Crozbyguy-rg1iu28 күн бұрын

  Is it brushless?

• 
  @kitronik27 күн бұрын

  Hi, and thanks for the question. We don't believe so, there is no indication from the manufacturer that it is. Although we haven't deconstructed one, it would be very unusual to find one at this price point that was. I hope this helps.

• 
  @CyberCzar0Ай бұрын

  Superb invention! Shut up and take my money 👋🏻💸💸💸

• 
  @joesmith9103Ай бұрын

  What was the thickness of the bendable PETG sheet used in the video?

• 
  @kitronikАй бұрын

  H and thanks for the question, it's been a while since this video was made but I think it was 0.5mm sheets that can be found here: kitronik.co.uk/products/43217-clear-petg-sheet-0-5mm-x-297mm-x-210mm-a4

• 
  @mattijsbuys9846Ай бұрын

  Are the pinholes still usable in combination with this board? ea. lighting up a led on pin "x" while a motor is running? Thanks!

• 
  @kitronikАй бұрын

  Hi and thanks for the question, the micro:bit pins are broken out to pads on the rear of the board that can be used to connect to additional components and devices. These pads can be soldered to. I hope this helps.

• 
  @mattijsbuys9846Ай бұрын

  @@kitronik absolutely! Thank you.

• 
  @Misis1984Afzaal-gj1psАй бұрын

  Ac servo mini controler ? کیا اے سی سروو موٹر کے لئے بھی کوئی مڈیول دستیاب ہے ؟

• 
  @kitronikАй бұрын

  Hi and thanks for the question, unfortunately we don't stock any at the moment. Sorry that I couldn't not be more help with this.

• 
  @user-ly5ok3jd7mАй бұрын

  What is postcode of Nottingham Kitronik factory

• 
  @kitronikАй бұрын

  Hi, our postcode is; NG8 4GP I hope this helps.

• 
  @user-ly5ok3jd7mАй бұрын

  How can I order plastic sheets?

• 
  @kitronikАй бұрын

  Hi and thanks for the question, head over to our website and see if you can find the product that best fits your needs. kitronik.co.uk/collections/perspex-acrylic-sheets

• 
  @HollywoodColtАй бұрын

  A few pounds of what?

• 
  @redwater86Ай бұрын

  Is there any info on how to use the breakout pins? Could I use them to light up a LED for example?

• 
  @kitronikАй бұрын

  Hi and thanks for the question, All of the pins of the Pico that are not in use for the motor/servo connectors are broken out, 27 connections in total. They can be used to drive additional external devices such as sensors or ZIP LEDs. The breakouts are in the form of solder pads, located underneath where the an inserted Pico will sit and they can be soldered to. The pads have a direct connection to an inserted Pico and can therefore be used in exactly the same way as the headers soldered to the Pico. I hope this helps.

• 
  @metaphysicalArtistАй бұрын

  Is there a "Micro:Bit V3" going to be released soon , anyone know if this is going to happen?

• 
  @kitronikАй бұрын

  Hi, thanks for the question. We haven't heard of one in the works as of yet. The V2s are still pretty recent, so they are likely to be the standard for quite some time.

• 
  @metaphysicalArtistАй бұрын

  @@kitronik The micro:bit v1 was released on February 10, 2016, and the micro:bit v2 on October 13, 2020. Given the advancements in technology, 2025 could be a potential year for the v3 release! In the next upgrade, I would like to see features that make the micro:bit more universally accessible and versatile. What would you like to see in the next upgrade?

• 
  @alexsharp-ez2vgАй бұрын

  I want to know the code for it and how to connect it to a micro bit extension board

• 
  @kitronikАй бұрын

  Hi Alex, I will look into producing a guide. In the meantime, this board is great for this purpose; kitronik.co.uk/products/5673-kitronik-simple-servo-control-board-for-bbc-micro-bit Also there is a more up to date Klaw here: kitronik.co.uk/products/25104-klaw-mk2-robotic-gripper-kit I hope this helps, keep an eye out for a guide.

• 
  @sumangupta8573Ай бұрын

  Mujhe 1 sheet chahie local market me available hoga???

• 
  @kitronikАй бұрын

  Hindi: kshama karen, ham bhaarat mein sheet saamagree nahin bhejate hain. parivahan laagat graahak ke lie ise bahut mahanga bana detee hai. sthaaneey saplaayar dhoondhana behatar hoga. kshama karen main aur adhik madad nahin kar saka. English: Sorry, we do not ship sheet material to India. Transportation costs make it very expensive for the customer. It would be better to find a local supplier. Sorry I couldn't help more.

• 
  @ArturFranciscoAntunesdeSousaАй бұрын

  Olá! Resido no Brasil, vocês tem disponibilidade de envio para o meu pais?

• 
  @kitronikАй бұрын

  Olá! Não enviamos para o Brasil no momento. Desculpe. Acho que os nossos distribuidores portugueses, como a opencircuit, sim. Use o menu suspenso ao lado do botão adicionar ao carrinho. Espero que isso tenha ajudado.

• 
  @ArturFranciscoAntunesdeSousaАй бұрын

  @@kitronik Olá! Pronto, vou procurar essa empresa para saber sobre o envio.

• 
  @yaimem2 ай бұрын

  If there was a feature to center the servos, this product would blow up among RC hobby builders

• 
  @kitronikАй бұрын

  Hi, and thanks for the question. There's a handy onboard trimmer potentiometer that can be adjusted with a small screwdriver. I hope this helps.

• 
  @gilescurtis50902 ай бұрын

  What is the laser you are using ?

• 
  @kitronikАй бұрын

  Hi Giles, I think the one in the video is one of our 'Just add Sharks' lasers.

• 
  @santsikupponen2 ай бұрын

  thank you for the informative and useful video! it was well explained!

• 
  @anshuljain30072 ай бұрын

  Can this be used to suck air and create vaccum?

• 
  @kitronik2 ай бұрын

  Hi, although the pump can move air it is not rated as a vacuum pump. The only way to know for sure is to test it but we would be inclined to go for a pump specifically designed for this purpose. Probable outcomes of using this pump are likely to be unsatisfactory and may result in damage to the pump.

• 
  @andruszyk762 ай бұрын

  super, już zrobiłem, dziękuję za pomoc.

• 
  @TW392 ай бұрын

  Hi do they sell the mini linear acurators on the Google website

• 
  @kitronik2 ай бұрын

  Hi, We sell it from this page kitronik.co.uk/products/2595-linear-actuator Just below the add to cart button is a drop-down menu that allows you to select your country from the list and this will display all of the suppliers based in that country. If a country is not listed, it may be that neighbouring countries will ship to the missing country. I hope this answers your question.

• 
  @user-st8yi8ho7c3 ай бұрын

  How do I make a cover for it pls

• 
  @kitronik2 ай бұрын

  Hi, we did a blog resource showing how to make a custom enclosure for it, the blog includes free dxf's for laser cutting of the parts, I hope this helps. kitronik.co.uk/blogs/resources/making-an-enclosure-for-the-usb-rechargeable-torch-kit

• 
  @chjicken84883 ай бұрын

  saved my project thanks guys

• 
  @legendaryshadow64283 ай бұрын

  could I connect 2 dc motors and 1 stepper motor with this board?

• 
  @kitronik3 ай бұрын

  Hi and thanks for the question. Yes you can. Please note, when used with a stepper motor, half-stepping is supported - but not micro-stepping. There is more information on the datasheet: resources.kitronik.co.uk/pdf/5329-Pico-robotics-board-datasheet.pdf I hope this helps.

• 
  @tavishbachoomun98003 ай бұрын

  Thank you for helping me :) this was very useful You are a life saver

• 
  @Foreverexhailingegodeath3 ай бұрын

  I'm doing this instead of studying

• 
  @alfiz99433 ай бұрын

  It must have type-C power input!

• 
  @CrazyGaming-lw7cf3 ай бұрын

  Hi pls reply what is diameter of the pipe you used in this pump 😊

• 
  @kitronik3 ай бұрын

  Hi, and thanks for your question. The pipe has an inside diameter of 6.4mm and an outside diameter of 9.4mm. We supply i in 1m/5m lengths here; kitronik.co.uk/products/silicone-tube-for-use-with-6-12v-r385-diaphram-pump

• 
  @buensomeritano17554 ай бұрын

  Do you intend to make any thin film photovoltaic panels using your Sheetz as the backing substrate? Give them structural integrity and connections, and make them affordable and waterproof, and you really have something disruptive.

• 
  @buensomeritano17554 ай бұрын

  Do you sell any support structure pieces , like lightweight grid and load-bearing members, and connections for adding rigidity and strength in projects?

• 
  @kitronik3 ай бұрын

  Not at the moment but we can look into it for you.

• 
  @buensomeritano17553 ай бұрын

  @@kitronik I would think it would be a very profitable line of products for what you already sell. Definitely a worthy investment for your company.

• 
  @Nettle3144 ай бұрын

  I have an LED bulb which is 12v 35w, so 2.9a, but my power supply is also 12v. How do I calculate that? Cheers!

• 
  @aaaltairaaaaaaltairaaa934 ай бұрын

  Scratch

• 
  @kitronik4 ай бұрын

  Scratch is good too!

• 
  @Harrydell344 ай бұрын

  Thank you so much. This is very helpful

• 
  @keithlohmeyer4 ай бұрын

  Nice little project. I made a similar board using an atTiny85 that I use for the learn to solder classes I teach. Mine includes a buzzer and runs off a 3v coin cell. I don't have a power switch as the board goes in deep sleep. It still works after being on a shelf for 6 months. Great price I have about $4.50 in each of my kits in small quantities.

• 
  @keithlohmeyer4 ай бұрын

  I just got 2 of these and love them. I have a video showing a web controlled robot using one of these boards. kzread.info/dash/bejne/c66AuayDYKuvfcY.html Great little board for $10 US.

• 
  @hansdegroot85494 ай бұрын

  Great video. Thanks for sharing. Some years ago I bought some clock movements. Now I'm finally so far that i made my first clock. I took one movement out of the package, but the manual with it was very short. Only some hazy pictures or drawings. Your video gives me the courage to give it a try tomorrow. Assembly of all types of movements seems to be more or less the same. Every (first-hand = new) has a second hand mounted as the third (last) hand, I guess.

• 
  @SonicBoy1454 ай бұрын

  I don’t have one yet, neither a micro bit (it’s coming tomorrow), but I want to ask a question about this because I’m considering getting some. Are you able to activate/deactivate individual leds? I’m using Microsoft make code for it, if there’s not support for that in Microsoft make code is there any other softwares I can use to do that? Also for example I would want to place a green led at x3 y7.

• 
  @kitronik4 ай бұрын

  Hi, each LED is individually addressable with code. You can turn each on, and off, and change each LEDs colour independently of the others. MakeCode has blocks for these types of LEDs under the Neopixel menu but we have also produced some custom blocks for this LED panel that you can add to the editor. These custom blocks serve to simplify writing code for the tiles as much as is possible. In the editor; click on the cog icon in the top right and select extensions. This opens up a page with a search bar. Type and enter Kitronik and a list of all of our custom extensions will appear. Find the extension for kitronik-zip-tile, and click on it. The new menu should now appear in the editor with some new purpose-made blocks inside. I hope this helps.

• 
  @SonicBoy1454 ай бұрын

  @@kitronikAlright thanks! I’ll update you again once I get one!

• 
  @user-hu4rf1vf8u4 ай бұрын

  In ordinary motor pumps even motor is swiched off water flows in and out...no blocking..system. .what about this pump

• 
  @kitronik4 ай бұрын

  Hi, thanks for your question. When power is removed the pump will stop operating, so it will not pump water. I expect you will be able to force water through it but water won't flow by itself until the power is reconnected. I hope this helps.

• 
  @stupidscruff57945 ай бұрын

  Thank you!

• 
  @thenasutionfam5 ай бұрын

  How to connect v2 to it?

• 
  @kitronik5 ай бұрын

  Hi, it works in exactly the same way for V2 as it did for the previous micro:bit, just slot it in and you are good to go! I hope this helps.

• 
  @user-ch9wh6zk6f5 ай бұрын

  Can apply on this directly pu finish

• 
  @kitronik5 ай бұрын

  Hi, these sheets can be used with a pu finish like solid wood panels but may not withstand flexing after drying. Any bending could possibly cause imperfections to appear. I hope this helps.

• 
  @angelawhitehouse58175 ай бұрын

  Nice and easy thanks

• 
  @gavinrybicki27905 ай бұрын

  Is this pump rated for Isopropyl Alcohol? Or would this rust out?

• 
  @kitronik5 ай бұрын

  There was no information to say that it was rated for this. I would perhaps find a pump that advertises this fact, to be safe.

• 
  @milotorree5 ай бұрын

  PET? Or P.E.T LMFAO

• 
  @kitronik5 ай бұрын

  Hi, PETG or PET-G are pretty standard ways of writing it. Hope this helps!

• 
  @milotorree5 ай бұрын

  @@kitronik Pee - Eee - Tee Not Pet LMFAO

• 
  @dainzand59065 ай бұрын

  una pregunta el controlador de atras

• 
  @dainzand59065 ай бұрын

  god

• 
  @mahmoodarshed88145 ай бұрын

  Hi, I want to control 4 servo motors with this module with one button, how it's possible? Or there is any other module for several motors ?

• 
  @kitronik5 ай бұрын

  Hi and thanks for the question. We have a number of options for controlling servos for micro:bit and Pico. While we only have one that has been built with a single control button, the others can all be coded to behave in the same way. You can add a button to your project and have it control all connected servos in the same way. I hope this helps. The links show robotics boards and motor control boards that can also drive servos; kitronik.co.uk/collections/robotics/servo-control

• 
  @mahmoodarshed88145 ай бұрын

  @@kitronik thanks a lot for reply

• 
  @BLOCKPLAYER0225 ай бұрын

  Bugatti bolide