You got pull the tape when the plasti dip is still wet or it will lift it off the car
@travissteindl2 ай бұрын
It was unmasked immediately after the final coat it drys that fast
@SWACBUZZ2 жыл бұрын
Think you got to make closer 50/50 strokes with the can to keep from getting the tiger striping. Doesn't look terrible though. Good job! You should get the gun from DYC and not use cans. You have a garage so I envy you. I live in DC so I can't do this.
@Veganggg3 жыл бұрын
looks p good to me
@savealifecounselinggroup10703 жыл бұрын
I think you did a good job and i will follow the same steps to do the same on my pt cruiser
@agajohanna4283 жыл бұрын
should have peeled the 1/4" tape 1st, then the outer/centre 2" tape, then the plastic with Toronto Star news paper eh
@de_hortapbr94943 жыл бұрын
No quema cuh
@alexhoppe62143 жыл бұрын
BAAAAAAAAAAAM
@702xRyder3 жыл бұрын
Trick is remove tape fast or your screwed
@five7phew5504 жыл бұрын
It look good man’
@scottforbesjr64274 жыл бұрын
The guy at DYC said, and I found out myself, is to waste no time in getting the tape off before it drys. Helps a lot to have more than one person so you can get it off even faster.
@jonathanleslie91004 жыл бұрын
how much time between coats? how long was the entire job?
@alanarcher59544 жыл бұрын
Why not just use vinyl striping?
@travissteindl4 жыл бұрын
This is cheaper and more fun for me
@user-sx4yu3nw4j4 жыл бұрын
Tiger stripes. But yeah, you said it, it looks like shit. Good first attempt, and a great video for lessons to learn from.
@mcwip5434 жыл бұрын
No one: Open dif boys:
@ttv-doritosgod31234 жыл бұрын
Will this come off in the car wash ? I’m thinking about doing my Nissan Titan
@ChristopheZ4 жыл бұрын
my grille on my mercedes is plastidip in black....it goes thru car wash without issue. However, I like to wash my car by hand... I am doing stripes tomorrow ( in silver)
@DaleRoss5 жыл бұрын
Hey check out my burnouts videos
@Cobra_4275 жыл бұрын
doing a white bumble bee stripe on the tail of my black 2007 Charger SE, going to be a plain stripe just like some base models back in the late 60s
@michaelwarren82585 жыл бұрын
U have to go fast removing tape while wet or else you your edges will peel
@aaronfuksa20475 жыл бұрын
hurry, hurry! tape first! slow is not ideal, wet that coat, & get to pulling that tape up right away if you want sharp lines. only way. big areas need a spray gun for a quick pace.
@224chingon5 жыл бұрын
Great job close to perfect
@224chingon5 жыл бұрын
I hate the fact that when u are peeling the tape the plastidip starts to lift up. Had the same thing happen to me. Idk if you have to let it dry longer. Any one have any idea?
@WhatInTheActualHealth5 жыл бұрын
I learned the hard way. You actually want to peel the tape while it is still wet. When plasti dip dries, it will stretch and pull on the striped part. Hope this helps.
@travissteindl4 жыл бұрын
I used a heat gun to get it hot as I peeled the the masking tape off
@Zynbobway696 жыл бұрын
I own that truck now lol
@trayclark40986 жыл бұрын
How many cans did you use ?
@travissteindl6 жыл бұрын
2 cans
@islandboy74326 жыл бұрын
plasti fly lol
@kimbreanna94726 жыл бұрын
looks good!
@zacharymartin48616 жыл бұрын
That is one good sounding V6.
@evanrosario3 жыл бұрын
It's a 350 minus the front cylinders. My s10 blazer sounded decent with MagnaFlows.
Пікірлер
A little rough
You got pull the tape when the plasti dip is still wet or it will lift it off the car
It was unmasked immediately after the final coat it drys that fast
Think you got to make closer 50/50 strokes with the can to keep from getting the tiger striping. Doesn't look terrible though. Good job! You should get the gun from DYC and not use cans. You have a garage so I envy you. I live in DC so I can't do this.
looks p good to me
I think you did a good job and i will follow the same steps to do the same on my pt cruiser
should have peeled the 1/4" tape 1st, then the outer/centre 2" tape, then the plastic with Toronto Star news paper eh
No quema cuh
BAAAAAAAAAAAM
Trick is remove tape fast or your screwed
It look good man’
The guy at DYC said, and I found out myself, is to waste no time in getting the tape off before it drys. Helps a lot to have more than one person so you can get it off even faster.
how much time between coats? how long was the entire job?
Why not just use vinyl striping?
This is cheaper and more fun for me
Tiger stripes. But yeah, you said it, it looks like shit. Good first attempt, and a great video for lessons to learn from.
No one: Open dif boys:
Will this come off in the car wash ? I’m thinking about doing my Nissan Titan
my grille on my mercedes is plastidip in black....it goes thru car wash without issue. However, I like to wash my car by hand... I am doing stripes tomorrow ( in silver)
Hey check out my burnouts videos
doing a white bumble bee stripe on the tail of my black 2007 Charger SE, going to be a plain stripe just like some base models back in the late 60s
U have to go fast removing tape while wet or else you your edges will peel
hurry, hurry! tape first! slow is not ideal, wet that coat, & get to pulling that tape up right away if you want sharp lines. only way. big areas need a spray gun for a quick pace.
Great job close to perfect
I hate the fact that when u are peeling the tape the plastidip starts to lift up. Had the same thing happen to me. Idk if you have to let it dry longer. Any one have any idea?
I learned the hard way. You actually want to peel the tape while it is still wet. When plasti dip dries, it will stretch and pull on the striped part. Hope this helps.
I used a heat gun to get it hot as I peeled the the masking tape off
I own that truck now lol
How many cans did you use ?
2 cans
plasti fly lol
looks good!
That is one good sounding V6.
It's a 350 minus the front cylinders. My s10 blazer sounded decent with MagnaFlows.
YOLO: You Only Left One
Blunder aside, that is an excellent sounding V6!