what about the bypass wire you put in the distributor? where did you get that? where are the timing marks? did you use an advance light and set timing to zero?
@davenero82437 ай бұрын
I have a Michigan Motorz 3.0 in a Bayliner Capri. Thing runs like a top.
@BackyardBeeKeepingNuevo10 ай бұрын
Can I get 300hp. out of my 5.0L?
@raza29411 ай бұрын
Hi need for ecu piout this engine
@dodanimgandara791 Жыл бұрын
Does the inboard starter have a rubber plug to lubricate starter?
@user-js4xl8if3z Жыл бұрын
Curious, My port standard rotation motor is setup exact to this, however my reverse rotation motor has a different distributor and setup on top of the motor, any idea why? I am also having timing issues since new, it sets off the knock sensor at 3K RPM and goes into limp mode. when hooked up it shows it placing 42 degrees of timing to the motor, not sure why
@ronaldoxavier5531 Жыл бұрын
Hi, I have 2002 boat with volvo penta going 5.0 now need new engine, I want change for 5.7 what need for make transformation? Thank you for your time,
@roycejustavino5662 Жыл бұрын
I live panama central america i love these engines music to my ears
@roycejustavino5662 Жыл бұрын
You are the best instructor explain good
@gregfiegelist5165 Жыл бұрын
sweet
@drifter9425 Жыл бұрын
Baby RUNS Now sneak up on all the new boat owners and hurt their feelings
@andrewwesney7441 Жыл бұрын
Can you still buy these?
@wesg6974 Жыл бұрын
I will be replacing my volvo penta 5.0L GL cracked block with a 5.7L gm vortec block, which gasket kit do I need to buy?
@jimwithers7265 Жыл бұрын
Is there a separate fuel water separator? Where would it be located? Between tank and fuel pump/filter you show? Thanks
@Thecloughs816 Жыл бұрын
What was the top speed?
@TheRealKRUE Жыл бұрын
What was the cost of the install?
@dantheplumber3233 Жыл бұрын
Can you still get it?
@michaeltuckerman6983 Жыл бұрын
Wow holy cow the RPM just kept going and going wow
@chippyjohn1 Жыл бұрын
I am amazed that people still use pushrod engines. At least when you stop, you have a spare boat anchor.
@eaxnitro Жыл бұрын
Absolute beast of an engine. Love it!
@kilokyle2 жыл бұрын
Do you have any videos on fuel pump replacement for this type of engine?
@namechane17582 жыл бұрын
Why don't the exhaust manifolds need to be water cooled?
@stuartwood26772 жыл бұрын
MY engine immediately dies when I supply 12V to the black wire. I either cannot get into base timing or cannot get out of it, one of the two. Any thoughts?
@427TTM62 жыл бұрын
Same issue here .. any progress?
@stuartwood2677 Жыл бұрын
@@427TTM6 No luck. I shelved my boat project until now again. Still having the same issues and it's running like crap. Did you find out anything on yours? I've come up dry with my infinite google searches.
@TheWiesle2 жыл бұрын
will a reverse rotation engine run if the wrong starter is put on it and the wires are standard, because my 454 i got from a shop runs bad but its flywheel timing lines are backwards making me think it originally is reverse rotating but they couldn't figure it out so they sold it to me.
@rayfrye13352 жыл бұрын
Is this engine available for an alpha 1
@catarinoaviles75182 жыл бұрын
It’s for sale?
@c.riviera75002 жыл бұрын
Look at this account, he repost your video kzread.info/dash/bejne/g6ybtZSaf8SxcZc.html
@rodhonco56812 жыл бұрын
Did you reinstall the Volvo Penta ECM? Or did you order and install the VP 5.7L ECM?
@rvptwobee2 жыл бұрын
base timing EST wire was the information that I needed but unfortunately you showed how to point a timing gun and how to turn a distributor thanks
@michaelpotts30942 жыл бұрын
I have a 1964 fiber form that deserves that engine and out drive. Love the video thanks for sharing the neatness and quality of the craftsmanship. every body needs a hole in the water. also do you remember what the term B.O.A.T. stands for? bust out another thousand..... i guess the saying goes i do not care
@tonychavez20832 жыл бұрын
That’s a beautiful thing. Would love that for my sea ray to replace the 5 liter w/ Alpha stern
@riduanrcb70432 жыл бұрын
Itu mesin bensin atau diesel bang ?
@jamespower92082 жыл бұрын
How much?
@claseaaa2 жыл бұрын
hey michigan motor. i have a similar engine, i pulled it to fix an oil leak as well as a broken Ypipe. now i want to run it on the floor (test it prior to install on boat) but i am not sure how to do this without a wire harness. can you offer any info?
@miketee24442 жыл бұрын
, I'm kinda guessing because it's been a while but just the exhaust manifolds were looking at are probably 6 grand. Not like there is much choice. Even if choking it down with some old Mercruiser stuff didn't bother you I'm pretty sure they won't bolt to these blocks.
@mattmayo35393 жыл бұрын
The small block Chevy is truly one of the most impressive and versatile modular V8’s ever built. Our local swimming pools has a pump that’s coupled to a small block Chevy that’s running on natural gas.
@makegaminggreatagain39073 жыл бұрын
I use to have a mullet but I got sick of the maintenance so I just shave my head, Supercharged V8's are like a reverse mullet, party in the front WeeeeeeeH, business in the back VroooooM.
@adawg44903 жыл бұрын
Wow they do exist
@jrac8633 жыл бұрын
I have a 2002 chaparral ssi 260 with a 8.1 volvo penta engine.The motor is blown .How much work would it be to replace that engine with a 5.7 mercury engine.
@citrusmcflygmailco3 жыл бұрын
What's the timing supposed to be for a 454 Big block Mark 4 casting# 14015445 crusader ch350? Original manual says 10° before top dead center but do I follow that considering most of when I'm hearing is not to follow original engine spec on timing with these or it could blow up the engine. Please help
@mikebirondo13293 жыл бұрын
My filter seems to be wedged into the bowl and I can’t get it out. Any suggestions?
@glenndeshields58743 жыл бұрын
Great explanation! Do you have a video on how to replace the fuel pump?
@jeremygoodner72912 жыл бұрын
I was just about to ask the same question!
@chumdinger83207 күн бұрын
3y later I’m guessing the answer is no
@alexmnblyth3 жыл бұрын
what kind of boat is this?
@connorspence83773 жыл бұрын
GM POWERRRRRRRRRR!
@TMcD33 жыл бұрын
Where do you get the jumper you plugged into the distributor for base timing?
@aNuthaRedneck Жыл бұрын
Build your own using scrap wire and two bullet connectors
@tltsw3 жыл бұрын
Chevrolet/GM is just better than Ford and Dodge. The aftermarket support that the LS engines have is unmatched. Ford has to turbo everything because they can't build a naturally aspirated engine with any kind of power. Dodge with their hemi are having so many Cam and lifter problems as well as fuel economy problems it's a joke. Chevrolet has always been the go-to aftermarket engine as far as I know. GM is just number one.
@andrewbowden10763 жыл бұрын
That rinky dinky hull has never gone so fast in its life!
@midwestcatz58963 жыл бұрын
@11:00 is when it gets good you can feel the joy in the boat.
@observadordelenjambre13583 жыл бұрын
I need a 5.0 mercruiser engine for my 1991 Bayliner boat. Do you have one for sale?
@observadordelenjambre13583 жыл бұрын
I need a 5.0 mercruiser engine for my 1991 Bayliner boat. Do you have one for sale?
Пікірлер
what about the bypass wire you put in the distributor? where did you get that? where are the timing marks? did you use an advance light and set timing to zero?
I have a Michigan Motorz 3.0 in a Bayliner Capri. Thing runs like a top.
Can I get 300hp. out of my 5.0L?
Hi need for ecu piout this engine
Does the inboard starter have a rubber plug to lubricate starter?
Curious, My port standard rotation motor is setup exact to this, however my reverse rotation motor has a different distributor and setup on top of the motor, any idea why? I am also having timing issues since new, it sets off the knock sensor at 3K RPM and goes into limp mode. when hooked up it shows it placing 42 degrees of timing to the motor, not sure why
Hi, I have 2002 boat with volvo penta going 5.0 now need new engine, I want change for 5.7 what need for make transformation? Thank you for your time,
I live panama central america i love these engines music to my ears
You are the best instructor explain good
sweet
Baby RUNS Now sneak up on all the new boat owners and hurt their feelings
Can you still buy these?
I will be replacing my volvo penta 5.0L GL cracked block with a 5.7L gm vortec block, which gasket kit do I need to buy?
Is there a separate fuel water separator? Where would it be located? Between tank and fuel pump/filter you show? Thanks
What was the top speed?
What was the cost of the install?
Can you still get it?
Wow holy cow the RPM just kept going and going wow
I am amazed that people still use pushrod engines. At least when you stop, you have a spare boat anchor.
Absolute beast of an engine. Love it!
Do you have any videos on fuel pump replacement for this type of engine?
Why don't the exhaust manifolds need to be water cooled?
MY engine immediately dies when I supply 12V to the black wire. I either cannot get into base timing or cannot get out of it, one of the two. Any thoughts?
Same issue here .. any progress?
@@427TTM6 No luck. I shelved my boat project until now again. Still having the same issues and it's running like crap. Did you find out anything on yours? I've come up dry with my infinite google searches.
will a reverse rotation engine run if the wrong starter is put on it and the wires are standard, because my 454 i got from a shop runs bad but its flywheel timing lines are backwards making me think it originally is reverse rotating but they couldn't figure it out so they sold it to me.
Is this engine available for an alpha 1
It’s for sale?
Look at this account, he repost your video kzread.info/dash/bejne/g6ybtZSaf8SxcZc.html
Did you reinstall the Volvo Penta ECM? Or did you order and install the VP 5.7L ECM?
base timing EST wire was the information that I needed but unfortunately you showed how to point a timing gun and how to turn a distributor thanks
I have a 1964 fiber form that deserves that engine and out drive. Love the video thanks for sharing the neatness and quality of the craftsmanship. every body needs a hole in the water. also do you remember what the term B.O.A.T. stands for? bust out another thousand..... i guess the saying goes i do not care
That’s a beautiful thing. Would love that for my sea ray to replace the 5 liter w/ Alpha stern
Itu mesin bensin atau diesel bang ?
How much?
hey michigan motor. i have a similar engine, i pulled it to fix an oil leak as well as a broken Ypipe. now i want to run it on the floor (test it prior to install on boat) but i am not sure how to do this without a wire harness. can you offer any info?
, I'm kinda guessing because it's been a while but just the exhaust manifolds were looking at are probably 6 grand. Not like there is much choice. Even if choking it down with some old Mercruiser stuff didn't bother you I'm pretty sure they won't bolt to these blocks.
The small block Chevy is truly one of the most impressive and versatile modular V8’s ever built. Our local swimming pools has a pump that’s coupled to a small block Chevy that’s running on natural gas.
I use to have a mullet but I got sick of the maintenance so I just shave my head, Supercharged V8's are like a reverse mullet, party in the front WeeeeeeeH, business in the back VroooooM.
Wow they do exist
I have a 2002 chaparral ssi 260 with a 8.1 volvo penta engine.The motor is blown .How much work would it be to replace that engine with a 5.7 mercury engine.
What's the timing supposed to be for a 454 Big block Mark 4 casting# 14015445 crusader ch350? Original manual says 10° before top dead center but do I follow that considering most of when I'm hearing is not to follow original engine spec on timing with these or it could blow up the engine. Please help
My filter seems to be wedged into the bowl and I can’t get it out. Any suggestions?
Great explanation! Do you have a video on how to replace the fuel pump?
I was just about to ask the same question!
3y later I’m guessing the answer is no
what kind of boat is this?
GM POWERRRRRRRRRR!
Where do you get the jumper you plugged into the distributor for base timing?
Build your own using scrap wire and two bullet connectors
Chevrolet/GM is just better than Ford and Dodge. The aftermarket support that the LS engines have is unmatched. Ford has to turbo everything because they can't build a naturally aspirated engine with any kind of power. Dodge with their hemi are having so many Cam and lifter problems as well as fuel economy problems it's a joke. Chevrolet has always been the go-to aftermarket engine as far as I know. GM is just number one.
That rinky dinky hull has never gone so fast in its life!
@11:00 is when it gets good you can feel the joy in the boat.
I need a 5.0 mercruiser engine for my 1991 Bayliner boat. Do you have one for sale?
I need a 5.0 mercruiser engine for my 1991 Bayliner boat. Do you have one for sale?