Пікірлер

• 
  @oxamiiАй бұрын

  Hi

• 
  @dyndawariatАй бұрын

  POLSKA PRZEJMUJE TO VIDEO!!

• 
  @dyndawariatАй бұрын

  jorojojo

• 
  @dyndawariatАй бұрын

  GOOD JOB MATE

• 
  @mg53682 ай бұрын

  Thanks so much, really appreciate the video. 👍

• 
  @mpam0024 ай бұрын

  cswa has sheetmetal?

• 
  @mpam0024 ай бұрын

  thanks for the video really helpful

• 
  @celestemunoz54415 ай бұрын

  THANK YOU!

• 
  @kevcopo10 ай бұрын

  This was awesome thank you

• 
  @user-nt7zb7wd2e11 ай бұрын

  How to validate the result

• 
  @omkarmane487311 ай бұрын

  how possible the 30 *30 and 60*60 area come reactangle

• 
  @user-vv2yc9vo5k Жыл бұрын

  Is there any way to combine properties of two material in single solid? For example combined property of 88% silver and 12% PET. Can we assign such kind of material in ANSYS workbench static structural?

• 
  @danielalonso5533 Жыл бұрын

  thank you.!!! Greetings from Peru

• 
  @ikacar Жыл бұрын

  Thank you. Is it possible to probe (find out) a moment reaction on a rotational joint (or any jont) where I applied rotational velocity in RBD? how could I calculate "the necessary design torque (reaction)" to balance the moment caused by other loads? As I experienced from Ansys RBD, when a rotational joint is free to rotate, no torque reaction is induced about this free axis. Should I apply additional constrain its rotational axis where I will take torque reaction? But if I constrained the rotational DOF, how could I apply rotational velocity (or any load) to this constrained axis (DOF)? Is there any easy way or technics to probe torque requirement (reaction)?

• 
  @ameyvikramsudarshan7356 Жыл бұрын

  Please tell me how to learn ansys and what should be learnt ansys software

• 
  @ameyvikramsudarshan7356 Жыл бұрын

  Good morning sir, Very nice video

• 
  @mea_335_hiranyamodak6 Жыл бұрын

  very helpful video, ill use this in my project!

• 
  @alvianricoristian48692 жыл бұрын

  Thanks for the video!

• 
  @Colin96tv2 жыл бұрын

  It doesn't import material properties when you import it as a step for anyone that wants to save 9 minutes and 43 seconds of there life from watching his horrible video

• 
  @LeRainbow2 жыл бұрын

  Anyone know how to import CREO models to be used in Ansys for kinematic analysis? I have read every single ANSYS help file, I have contacted ANSYS support but to no avail.

• 
  @KHollow44442 жыл бұрын

  Hey Binsu, I have a UDL of 1KN/m on a 5m 3D Rectangular model.. could you pls help me? Do i apply "force" on the face, or do i apply Pressure on the Face?

• 
  @rajeshmudavath31042 жыл бұрын

  noice

• 
  @ascaputra81033 жыл бұрын

  hello , my name is asca. I am a student of mechanical engineering institute technology of sepuluh nopember. I have some problem in my simulation in rigid dynamic using ANSYS. can I get your email ? hope you can help and discuss with me about my issue. thanks..

• 
  @cadfeamechanical29223 жыл бұрын

  thanks buddy

• 
  @huzaifajalgaonkar67673 жыл бұрын

  Awesome doubts cleared👌🏻👍

• 
  @milindkulkarni99143 жыл бұрын

  Sir can you also upload the video for CFD in ansys

• 
  @kishanpatel56753 жыл бұрын

  Bro I want one help

• 
  @rahulajitparab30863 жыл бұрын

  Thank you sir Video was very helpful 😄😄😄

• 
  @wilson63173 жыл бұрын

  Hi sir , how to measure the acceleration at the end of slider?

• 
  @botulysses99414 жыл бұрын

  Very helpful video 👍👍

• 
  @rishabnaidu39755 жыл бұрын

  Part mail karna!!!!

• 
  @bhaskarreddy50796 жыл бұрын

  Assembly drawing are more prefer manual drawing than animation

• 
  @mangeshsingh67776 жыл бұрын

  Can you please provide the detailed 2D drawing this particular component? It is urgent. Thank you.