Пікірлер

• 
  @dannyalley375327 күн бұрын

  Would have been much better if I could have heard you

• 
  @davidtrees2430Ай бұрын

  Have you done the other side YET... lol

• 
  @davig8829 күн бұрын

  Yes ! Just did them this morning... boy it's HOT outside .

• 
  @mattkenaston71805 ай бұрын

  Thanks for putting this out there.! I just picked one up not realizing how unique these rear ends are. I'm going to try narrowing mine to fit under my old international loadstar.

• 
  @davig885 ай бұрын

  That would be Good.

• 
  @dgreen80796 ай бұрын

  Great taste in Jeeps and music A++!

• 
  @MrKyle5137 ай бұрын

  1:25 horn works 🤣🤣

• 
  @davig887 ай бұрын

  Hahaha

• 
  @_Machine631_8 ай бұрын

  when you drill you dont drill full speed. slower the better. also you never torque suspension off the vehicle. tighten bolts a little bit. then once suspension is loaded, THATS when you torque them.

• 
  @davig888 ай бұрын

  Yuppers

• 
  @cerberus4510 ай бұрын

  Man! wish I would've watched this video before buying my master install kit - that DRK311 kit is the same thing and would've saved me $40 at least. Thanks for sharing

• 
  @davig8810 ай бұрын

  Your welcome

• 
  @Travispulliam Жыл бұрын

  My 2001 Ford f-150 2wd 4.2 v6 done good on the first one

• 
  @elijohnson8323 Жыл бұрын

  where were you guys sir?

• 
  @davig88 Жыл бұрын

  Tennessee west side of 75 in the TWRA area.. some was capuchin creek and 1st part no clue... lol..

• 
  @deano216 Жыл бұрын

  Sweet...

• 
  @davig88 Жыл бұрын

  thanks

• 
  @maxrogers762 Жыл бұрын

  Awesome video! I'm in the middle of doin a 8.8 swap, what did u do about the zj abs? Thanks🤘

• 
  @davig88 Жыл бұрын

  I ground down every other tone ring point.. hooked up both sides to the 8.8 sensor.. that's how I did mine...

• 
  @petrokiller1 Жыл бұрын

  Nice ZJ you have. Do you have a video about your rear bumper build?

• 
  @davig88 Жыл бұрын

  Sorry I dont. It's 4x4x.250 square, welded 4inch channel to hitch and bolt bumper to that... will hide under stock bumper cover...

• 
  @OverlandGeneration Жыл бұрын

  that hill has gotten rough!

• 
  @davig88 Жыл бұрын

  Yes and no..lol.. still fun , and video does no justice for it...

• 
  @mikethrapp Жыл бұрын

  Jealous. I need to get out so bad. But I also need to change my damn ball joints first lol. My ujoints aren't liking being locked on tight turns 😅 And I got a hub going out. 254k miles on factory ball joints 😂

• 
  @davig88 Жыл бұрын

  J.E.E.P..... lol

• 
  @deano216 Жыл бұрын

  Sweet

• 
  @Hypure2wheels Жыл бұрын

  Looks good man. I believe I'm getting ready to buy one. Seems to be exactly what I'm looking for.

• 
  @davig88 Жыл бұрын

  Been great so far... I've pulled a few jku up some big hills while rear tied to a tree...

• 
  @patrickclapp1090 Жыл бұрын

  Badass build!! I wish mine was that far along. I even loved the music in the background!

• 
  @davig88 Жыл бұрын

  Thank you. Just out jamming in the barn..lol

• 
  @iflytango Жыл бұрын

  Yes great video showing the progress and greta van fleet.

• 
  @m988022 Жыл бұрын

  i wish i had known u were down, we could have got something to eat.

• 
  @m988022 Жыл бұрын

  i passed a ton of jeeps over the weekend one was a gen 1 with a convoy sign super authentic and cool

• 
  @davig88 Жыл бұрын

  Yes had two in an easy group ..hopefully next year we'll have 1 group for them..

• 
  @felixvargas4112 Жыл бұрын

  Hey Bud, Is that a rough country winch plate? And if so, does that winch mount with no problems.? (I have that apex winch, but trying to figure out what winch plate is plug and play?) Thanks

• 
  @davig88 Жыл бұрын

  Yes... I've video installing mount

• 
  @davig88 Жыл бұрын

  Yes.. perfectly

• 
  @Martin-xb2rz Жыл бұрын

  Why did Jeep didn't use wrangler axles on it? Why do they use a solid axles with axle cuffs?

• 
  @davig88 Жыл бұрын

  Mmmmmm...... don't know why jeep does what they do....

• 
  @DevinReavis2 ай бұрын

  Put your helmet back on champ.

• 
  @danhambrick6331 Жыл бұрын

  Nice job..Your buddy is very entertaining. 😁😁👍👍

• 
  @davig88 Жыл бұрын

  Haha yeah 🤣 thanks for watching...

• 
  @TheEaglePatriot Жыл бұрын

  Public or private? This looks like a blast

• 
  @davig88 Жыл бұрын

  KAT is all public roads.. lots gravel road and blacktop and trail type roads ... Kentucky Adventure Trail..

• 
  @akemonjames Жыл бұрын

  I ran from Oneida to Jellico in February . Trail has change a lot since then

• 
  @jlxcalixsurfer Жыл бұрын

  What part of Tennessee is that?

• 
  @davig88 Жыл бұрын

  Part of the KAT south west of jellico

• 
  @sydneychase7802 жыл бұрын

  Awesome job on the video! Better than the video from SEGA. maybe they just need to use a phone. God Bless..

• 
  @davig882 жыл бұрын

  Gopro 5..

• 
  @joecrone98622 жыл бұрын

  Way too cool! Thanks..

• 
  @davig882 жыл бұрын

  Sorry not jeep related..BUT was a blast to attend!!

• 
  @erikcarpenter78602 жыл бұрын

  Did you have to replace that brake switch?

• 
  @davig882 жыл бұрын

  No.. just the e brake spring was broken... would spring back..

• 
  @edzimdahl11582 жыл бұрын

  Per chance do you know if that zj was an factory upcountry edition?

• 
  @davig88 Жыл бұрын

  Just a Loredo

• 
  @edzimdahl11582 жыл бұрын

  From everything seen,, definitely glad you'll never work on anything of mine, tho you did get it done, in a fashion,

• 
  @davig882 жыл бұрын

  Cough cough

• 
  @JohnWeigold2 жыл бұрын

  Did you run this south to north? Or North to South?

• 
  @davig882 жыл бұрын

  I've done it both ways.. this is coming from the south side...

• 
  @shaggy42041 Жыл бұрын

  It's better to run south to north

• 
  @pcbmale2 жыл бұрын

  rear neeeds to be same degree as the transmission, both angles should be the same on both ends

• 
  @davig882 жыл бұрын

  Sorry... no it's a double cardin at transfercase

• 
  @ThatGuyMike2 жыл бұрын

  Where ya at?

• 
  @davig882 жыл бұрын

  Hahaha..just seen this.... forestry trail to Ravens overlook... Where you 2 BEEN ..your like invisible..lol

• 
  @landonreeder24622 жыл бұрын

  Do you remember what your pinion angle was? I’m installing the same kit, and do you have any tips about the brake lines and anything else unexpected you can across?

• 
  @landonreeder24622 жыл бұрын

  How long did it take from start to finish?

• 
  @davig882 жыл бұрын

  Hmmm... 2 or 3 days.. don't really know

• 
  @landonreeder24622 жыл бұрын

  You did good 👍🏻 You sold me on the rear long arms

• 
  @davig882 жыл бұрын

  @@landonreeder2462 it's amazing how nice it is on the Trails... I'll do more than I'll let it..lol

• 
  @channghiem50122 жыл бұрын

  face palming hose orange pumpkin things are RCV CROMOLY SHAFTS

• 
  @davig882 жыл бұрын

  Hahaha... most definitely

• 
  @molle2322 жыл бұрын

  Faster drilling with a Milwaukee cordless tool and sharp bits

• 
  @davig882 жыл бұрын

  Haha thanks..bits sharp.. upside-down is a pain.....

• 
  @MarcusEhrhardt2 жыл бұрын

  You forgot to keep cutting the rest of the bumper out on the sides.

• 
  @davig882 жыл бұрын

  Nope..learned the hard way on cutting the rear supports out..saggy Rear now pop canning the hatch... had to do a ton of bracing... may ill do a video of my wrongs ..lol

• 
  @MarcusEhrhardt2 жыл бұрын

  @@davig88 Lots of guys do it on the ZJ looks way cleaner, and gives much more front tire clearance. I'm getting ready to do mine. Then its the front winch setup like yours. Nice.

• 
  @davig882 жыл бұрын

  @@MarcusEhrhardt understand that..

• 
  @tejasenduro73622 жыл бұрын

  The ZJ is looking great!🤘🏼

• 
  @davig882 жыл бұрын

  Thank you.

• 
  @haroldsams-hs2 жыл бұрын

  where is this? thanks

• 
  @davig882 жыл бұрын

  Off of the Sheltowee trace trail...

• 
  @typicalpupet2 жыл бұрын

  Who’s M715 is it

• 
  @davig882 жыл бұрын

  Guy in our offroad club

• 
  @typicalpupet2 жыл бұрын

  @@davig88 Does he have any kind of media?

• 
  @davig882 жыл бұрын

  @@typicalpupet NO he"s lame... LOL... i keep telling him toooooo....

• 
  @usafyuros61262 жыл бұрын

  Awesome man

• 
  @thebear19472 жыл бұрын

  It was in the title Iron rock off road. What kind of welder and welding rod did you use? This will be the first time to do any welding on my frame.

• 
  @davig882 жыл бұрын

  Hobart 210 mig .030 wire.. On My 1st 8.8 install I used arch just normal everyday rod..can't remember

• 
  @thebear19472 жыл бұрын

  That is a great repair.. Where did you get those stiffeners? My crossmember is coming down due the the a/c drain routed thru the frame.. Thanks

• 
  @davig882 жыл бұрын

  IRONROCKOFFROAD.COM

• 
  @memphis285712 жыл бұрын

  My wife has a JLU with 33’s and a 2” lift, everything else is stock. Think we would be able to do all of the easy/medium lines?

• 
  @davig882 жыл бұрын

  You should be Fine

• 
  @ThatGuyMike2 жыл бұрын

  Nice!!!

• 
  @davig882 жыл бұрын

  You still hiding..lol

• 
  @romeshter3 жыл бұрын

  excellent video, did you get the abs to work? I'm in the process of swapping a jk dana 30hp into my zj and I need my abs to work. I'm also swapping the jk dana 44 on the rear. Any help would be greatly appreciated. Thanks

• 
  @davig883 жыл бұрын

  I didn't even hook it up..didn't want to bother with it.. no lights on either..but I would believe if you just hook it up it may just work..

• 
  @usafyuros61263 жыл бұрын

  Man my pos Dana 35 died on me, awesome vid man

• 
  @davig883 жыл бұрын

  Thanks.. I need to do an update.. still fine tuning it..

• 
  @codylee51323 жыл бұрын

  Did you make the bracket in the rear that the d rings are mounted to? Awesome rig man.

• 
  @davig883 жыл бұрын

  Yes out of 1/2 plate