At ECU Testing we want to challenge the status quo, when it comes to expensive car parts we believe in thinking differently…
We believe that a failed electronic control unit (ECU) should not have to cost a fortune. We think it is reasonable that you should not have to buy a new unit from the manufacturer. Just because they say you should.
We believe you should have the choice to have your existing control unit rebuilt, a choice that saves money, time, energy and natural resources. We also believe you should expect a rebuilt unit to perform exactly the same, if not better, than buying a brand new unit from the manufacturer. We believe you should be aware of what is happening at every step of the rebuild process so you can effectively plan your transport while your car is off the road.
Пікірлер
I have p0726 code on audi a3 2.0 tdi 2005 I changed crankshaft sensor but the car its the same shut down and indicator light its open and something is shut down Is this test voltage the same to my car or not ? Whats is the problem? Any solution?
Thanks for the advice! Im working on a Bobcat track loader, but I suspect the ecm protocol is likely very similar. These guys had the battery cables come off and shorted, which caused the machine to die. I suspect they fried something, but gotta figure out what
Awesome video. I've just finished assembling the DQ500 fitted to a Tiguan with a new clutch assembly and oil cooler due to water damage. The vehicle was towed in with the transmission stripped. After installing and starting, the transmission has no gears and refuses to complete basic settings throwing a fault code P060700 Control Module Performance. Any suggestions?
Good job..idol..
I just subscribed. Your video give as a lot of ideas on diagnosing wiring troubles. Im in a auto mechanic school in California and looking for a electrical training shop
Can u not physically clean up the sensor ?
awesome. really helped me out
Absolutely terrible video. Yeh he’s right but most often it’s a fuse that’s gone. Go into the handbook guide and check which fuse. Swap it out for one with the same amp and test it
Great video. Thanks
Grateful to provide this beneficial information to us. It's wonderful your Intellectual skills.
I found the problem the steering wheel is on wrong side 😉
I have a 2018 Tiguan TSi but I can not locate info if this is a DQ200 or DQ381. The Tiguan is going to a limp mode with code P0805 and/or P0810 ?(clutch position sensor circuit) not the codes that you mention (P173500 /P173600). is that the same process ?
What about the 2004 z4? We have currently this issue on my wifes car! This has the electric steering. What i am saying is why 2006 on ?
Mine went into neutral while driving. After restarting the car twice the car operated properly. Does that sound like a problem you see? Thank you
Are you in the USA?
Hi. This is exactly what I need. I live in NJ. Typically what’s the turn around time and how much does this cost? Thank you
Bill Burr's British accent sucks.
My problem always starts with the tpms light. But then ill get other lights too.like the brake light or door ajar light,, oh ya and the AC always qits working. I can usually smack the dash and it goes back to normal. Slowly its been getting worse and more often
Volvo xc90 both front sensors failed within 15000 miles , although 5 year old car , oddly both went after brief heavy ish braking on different occasions , Volvo dealer answer new wiring harness and sensor £664 a time
excellent.
Thanks for the video! I subbed to your channel for the good info ! I spent all day today trying to diagnose a Bobcat tracked skid loader that is having electrical gremlins and it won’t power up the display panel. I traced the problem down to a faulty control/display module. Its always a little stressful calling bad modules when they cost $1500 dollars to replace! But based on everything I seen its gotta be the panel.
This is so well made. I have to say that this video is just incredible good and insightful. Thank you.
Hi! I have a p0342 low voltage fault. However on the 5v terminal of the sensor connector I have the same voltage of my battery around 12.4/12.5. How is this possible? Shouldn't I receive a high voltage code instead?
Hi sir..how about if the error code shows U010A? what does this actually mean? very little info on this specific error code on KZread. My Diesel powered- Isuzu Dmax has this problem soon after i replaced its EGR electrical component. The error code U010A cant be deleted on OBD2 scanner. Any idea?
Hi mate. Love your stuff, have been off doing electronic work for decades and you are a great help.
My 2012 focus all of a sudden lost complete power steering it came up on the screen Steering Assist Fault Service Required so I limp it home and put my fixed code scanner on it and do a scan and get all of this which one of the codes has always been there the one that says (Pats) Key b10d7 but all the rest of the codes here are new, 1. B00C5 2. B00b5 3. B0052 4. B0050 5. B0028 6. B0020 7. U0154 please help I have googled it and KZreadd it asked everyone I know and nothing non of the codes mentioned in your video are there and we have checked the rack and the boots on the ends are all in great shape no tares or damage it does not appear that any water could be causing the problem it was not raining nor had it been it was a nice warm dry day this just happened while pulling in to a parking lot of a service station please help any information at all. Thank you for your time.
ECU TESTING
great information thank you
@ecutestinglimited can you help me here. Ford edge...installed new crankshaft sensors and the code for bank A is still on. I set my meter to 20v and tested the connector. Both holes gave me only .02 That a bad wire harness?
Please can you do a video on Mercedes w205 no crank , no start. How to trace the ECU wiring diagram
Can I ship mine to you from Australia
Tanks 🎉
I mean subscribe 😊
Im gonna do it
When the conductor plate rebuilt puts on the transmission again limp mode turn off or it has to scan?
Where's the 🆕 new Excellent 👍🏻👍🏻 sir
Excellent 👍🏻👍🏻 Where is the 🆕
Hello, can it be replaced by a lever/gear stick from a range rover sport?
Good video can bus
Hi, if you have a short to voltage i assume that would appear as a parasitic drain, and potentially cause other issues, i have a qashqai that has a serious drain, and is missfiring and is giving codes for a can issue with the cruise control and there was another of the same code, i am trying to figure if its a module or wiring right now?
anyone can tell on E46, How many places we can isolate the BUS.(s) the car sometimes has mind of its own. sometimes windows dont work, sometimes ac, or sometimes wiper works own its own. or no indicator sometimes. his is after heavy rain. but the convertible was never driven on water. any input can help thanks.
Really great video thanks. I’ve got a RFA module u0001 00-08 error on my Ford fiesta 2014 and an engine ignition light on the dash. Gone through your tests but everything seems ok. The battery though is reading 12.39v across the terminals or the cars internal test reads it as 11.6v. Is it most likely simply a dodgy battery that needs to be replaced? I did get a strange resistance reading from the HS CAN though as it was rotating though numbers eg 35 40 23 with others sometimes flicking in like 77 I saw once and a hundred and something. ?
I have an 08 ford explorer with wheel speed sensor fault and abs pump and module failure. I replaced the wheel bearing assembly and ABS sensor harness with no success. The car beeps at me for 30 seconds every 4 mins. Its absolutely the most annoying thing ever. The car drives with traction control off which is super dangerous. I live in puerto rico and the ford mechanics are supposedly out like 2 years in the service department that deals with electrical problems. The cost of repairs if they did however fix it would be the price I paid for the car. I feel like im SOL. Any advice for fixing it myself or what route I can take in getting it fixed?
You absolutely need the cars wiring diagrams and drawings showing where the modules live and where connectors are. You could spend hours doing it blind.
❤❤❤❤
12V vs 7V can you please explain.... Why why why??? Today's modern cars eg Toyota Glanza, Toyota Taisor, has 12V and then drops to 7V in the door close signal voltage. Whereas, it used to be directly 12V when door closed and 0V when opened in old cars. But today's cars has 12V at door closed, and after 20 seconds, it drops to constant 7V. When opening, it drops to 0V. Why there's delay in dropping to 7V at door closed?? What's the significance of this 12V to 7V??? Please explain 😊
C1440 and c1963 2011 f150 66000 miles brake fluid changed at 50000 lights reset after each restart but sometimes can drive several miles before they come back on sometimes can barely move the truck and they come on wandering if the problem is abs module or transducer in pump housing which I understand is unserviceable and parts cannon shot is 2000 I can’t imagine what the dealer would say but I am interested in verify problem myself before I present it to a shop as this information would help narrow my search in the landmine field of good guys and bad guys also tempted to buy the equipment and repair for free as many as possible to get back at the bad ones my plan is only flawed by making the good ones suffer as well please help if you can I appreciate your time and effort to enlighten us all
Hey.. how about fault code P0344 what does that mean?? We have peugeot 2008 2018 model that throws P0344 error and sensor and wiring loom are fine.. what do you think is the problem???
Please show the inductor clavation of the delete vehicle
Very informative video. Thanks for the info.!
Great video I am still trying to find out what my car will not start. Maybe you can point in right direction. Car sat for 6 years. It's a 1998 Volvo S70 GLT. I cleaned out fuel tank, replace fuel pump and fuel filter. I cleaned injectors. Car cranks has spark and fuel out the injectors. I thinking must be a sensor where the timing is not lining up with the spark and injected fuel. Any thoughts