Welcome to George Made This!! If you didn't already guess, I'm a maker (and eater of pizza)!
I hope you enjoy my videos. I have a website you can see here: www.georgemadethis.com I'm also on Instagram as georgemadethis.
Send me an email, comment, I'll do my best to reply!
Пікірлер
Hi! What 90° corner clamps did you use?
Hey! So the ones I use in this video are just Irwin Quick Grips but they used to do attachments for them to do a whole load of different things. I’m not sure if they still do them but it’s worth a look!
Im gonna be building one of these soon so im lookin for a rough guide.. i sure wish i had all those tools xd
Hey! Thanks for watching the video! I’ve got plans available on Etsy if you want to build it. There’s a comment pinned at the top of the comments. It’s easy to build with simple hand tools too!
Hey Everyone! For those that have been asking, and those that were wondering if there are any, I have finally produced some plans for the Coldframe! They are available to purchase from my Etsy page here: georgemadethis.etsy.com/uk/listing/1714777387/how-to-make-a-mini-greenhouse-coldframe From 14/04/24-21/04/24 you can get 10% off the plans using the code 'PLANS10' - make sure you tag me on instagram @georgemadethis if you do end up building this! Thank you and happy making!
Hi how to cut slots in wood to fix the window glass ?
Hi, to do grooves in the timber you’ll need a router and router table. I go into more detail about the method I use in this video in the plans I’ve made. Link is in the description 🤙.
Are there plans/material list for this Mini Greenhouse?
Hi! I am currently working on a set of plans. These will be available very soon!
@@GeorgeMadeThis I would like to sell this on a e-store I’m planning on building. What’s the best email to reach you at?
Send me an email at [email protected].
Bro…
awesome mods
Awesome video! I've been looking for ideas to build one of those myself and this is just what I needed. Could you explain a little more about the material you have used for the clear panels?
Hi, it’s called twinwall polycarbonate. It works really well for insulation. I’ve actually just made plans for this, the link is in the description if you want to check them out 🤙
Enjoyed the video and the music
Thank you! I’ve actually just made plans for this if you want to build one yourself. The link is in the description if you want to check them out! 🤙
Hi 👋 is there a reason why you left a cap on the back panel in the bottom? Aka didn't leave it flash with ground and only back one? Ps! Aswome video as I'll attempt to build one myself one tomorrow 🤞🫣
WHY do people feel the drive to put music, often too loud and only to their taste in the video??? I quit this one because of that and noted to never watch George again. Probably no loss, but maybe this week's YT check is little less.
Ya the music sucks, but the video itself is great. Clean little build.
George is representing himself in this video so it would make sense to have music that appeals to him. You can always turn it down and use the subtitles. Good video, good music! Long live woodworking!!❤
where is the cut sheet to build it?
I’m finally working on a set of plans so these will be available soon!
Can I ask what you’ve used to finish it? As it’s the exact colour and finish I’m looking to do
👏👏👏
👏👏👏
👏👏👏
👏👏👏
What size was the wood frame 2x2 or 4x2? And how thin did you cut the inlay wood for the window please, my partner made me one but he attached the perspex on the outside of the wood also I have a large gap between doors and the one side at the top that opens upwards 😪 I'm wanting too try and make one myself as love a challenge. Thanks for sharing.
Hi, it was smaller than that. Around 1x2 should do it! You can use 2x2 if you’d prefer but that may make it too bulky. Good luck!
Great vid, I can't wait to give this a try!
Thank you! I’ve actually just made plans for this if you want to build one yourself. The link is in the description if you want to check them out! 🤙
Would you be willing to share the measurements for the angles. I’m currently building this and don’t have the actual measurements for the angles.
Hi, I eyeballed the angles for these bits so am afraid I don’t have this measurement. If you hold the piece up to the sides of where it has to go you can mark the angles on it that way and cut them how you see fit. Hope this helps!!
It's amazing man. Can it be made taller too?
Hey, thank you! It absolutely can be made taller, wider deeper, to match whatever spec you’re working to. I think I based mine off one I found online.
@George Made This. Great, thank you for replying, really appreciate it
Could you be so kind to share with us those specs you got online ? Im trying to build one similar to yours but i need the lengths and dimensions of the wood so i can order it.
Is your timber sawn or PSE, could you use glass instead of plastic? Thanks.
The timber I use in this video is Roof Batten so I would say it’s sawn. Smoothed out quite easily with a quick sand. You could absolutely use glass!
@@GeorgeMadeThis Many thanks, in old money 1" x 1 1/2" I think. My builder's merchant seems to sell it in 3 plus metre lengths... dyed blue!
Exactly what I was looking for Do you have design drawings?
Hey! I’m glad you like it. I don’t have drawings I’m afraid. Maybe this is something I should look in to as a lot of people have asked.
@@GeorgeMadeThis Did u happen to make the drawings? Im interested in starting this but I'm not sure what type of wood or size/ thickness i should get
Looking at building one of these myself. I bought a small item similar from a high street store. Has a metal frame, I think three shelves and a plastic cover with two zips. Great at first but when the sun hit it for one summer, the plastic cover started to shrink slightly making the zips tricky to do up all the way because of how tight it is and it's also gone a bit brittle and in places, the plastic has started to crack. Looking at routing out a groove for the perspex to fit into rather than fitting strips of wood - only down side is replacing a panel if it gets broken :/
Newer ones I make I do route a groove to fit the panels in, yes it is a pain if a panel gets damaged but can just be unscrewed to replace. Using grooves does speed the building process up as well
can you please give us the size ? thanks
Hi what size are the ripped woods? 1.5x1.5?
Hi, the main frame of the coldframe is 38x20mm approximately and the bits of trim to hold the glazing in are about 10x10mm.
Also that step where you added the brass coating more than likely absolutely wrecked the heat treatment on the blade
Most likely, but I had fun doing it.
@@GeorgeMadeThis don’t hate me please 😂 I sent a picture of your knife to a knife collector irc community and they are all having a moment of silence for the opinel. They want me to deliver the message “RIP”
Haha no hate. I’m glad to cause a stir in the knife collector community.
Call this a “grind point” because you ground the tip off instead of clipping it 😂
awesome!
Thank you! I’ve actually just made plans for this if you want to build one yourself. The link is in the description if you want to check them out! 🤙
Great video! Any advice for us noobs on how to avoid screwing into screw when adding the diagonal pieces?
💯👍👍
💯👍👍
💯👍👍
💯👍👍
💯👍👍
Very simple yet still decent. Did you bother to sand it all at before applying a finish?
Thanks, I don’t remember but it would have only needed a light sanding. The timber I use for this is pre-treated. I just add on an outdoor furniture treatment from screwfix to be safe!
@@GeorgeMadeThis no worries 👍
I love how you're homing those as you drill into them 😉.
Sure if I had a little cnc machine like that things would be pretty easy
Haha, nothing that can’t be done with a ruler, pencil and a little patience.
One of the best woodworking videos I’ve seen! Thanks
Thank you so much! I’ve actually just made plans for this if you want to build one yourself. The link is in the description if you want to check them out! 🤙
Robert Dowely Junior
Loved this! You have a great style and make it look super easy. I fear my attempt may end up looking like the inbred 3rd cousin of yours😳
Is it possible to show how to make something like this with just ordinary hand tools, not all of us have a great workshop like yours. Just a simple DIY of putting things together would be great. Your talent is much more appreciated than that Noise or some would call it music.
nice work bro
Thank you!
George, cracking video mate, all being well am going to attempt making one in the next few months. Thanks for sharing your design, Cheers :)
Ahh fantastic! Make sure you share it with me on Instagram if you’re one there! I’d love to see it :).
@@GeorgeMadeThis Cheers George, I'm not on instagram, but if it works out i'll get a snap to you somehow, have a great weekend 👍
Fantastic! You too! You can always email me it: [email protected]! Thanks Jimbo!
@@GeorgeMadeThis Cracking cheers George, will do 👍
Great video and build! I was wondering, would you be willing to share approximate price for this project? I appreciate the difficulty, since most of your material would already live in your workshop, but I’m wondering if it’s more cost efficient for me to purchase a pre made :) I have the relevant tools and machinery already, tia
Thank you! I think it was around £100-150 for materials. Could be less if material prices are coming down slightly… I think you can buy one for £150 from shops but a lot of the reviews say they are quite flimsy… on newer ones I make, I route a groove in all the pieces to accept the polycarbonate, rather than cutting strips like I did in this initial one. It keeps the polycarbonate held a lot more firmly. Hope this helps!
@@GeorgeMadeThis thank you that’s great, I think I’ll buy this one I’ve found online for £80 and self adapt. Thanks once again, your one looks great quality so I know where to come to learn should mine break
@@chloethegreybuild8655 no problem! Glad the video can be of help :).
@@chloethegreybuild8655 I've often wondered about the price of building it yourself vs bought and quickly realised after being asked to price up a couple items I've made for other people. Most popular item was the recycle bin storage unit. Didn't think of it when I made mine but after being asked to make it for others, I had to do some research. In short, turned out that although mine was expensive, I just could not compete with people who were making the same items regards to price. What I noticed in every case though was mine was much stronger. I refuse to skimp on quality of materials and joinery methods and that's mainly where it shone through. Items from competitors were using really low quality wood and the quality of build (mainly the joints) were nowhere near as good as mine. Just thought I'd share what I found out.
Amazing 👏. Love the slow motion with the sander 😂.
Thank you!
Very talented and festive too! 👌 Love the soundtrack, can't beat a bit of the nutcracker!
Ahh thank you! It’s a beautiful piece of music!
Did you use the Nutcracker music while making a Christmas tree🤣🤣
Yes I did haha.
@@GeorgeMadeThis If only there was a song dedicated to the Christmas tree eh? That would have been perfect🤣
Haha if only! 🙄
Nice! This is great jig for any woodshop! 🙌👏
Stated to watch the video but the music was really annoying so I went to another channel.
Thanks for sharing 👍