Hi Everyone! I'm Aslam Hossain. I'm an undergraduate student of Electronic and Telecommunication Engineering at International Islamic University Chittagong. On this channel, you'll find video tutorials on a wide range of electronics projects, from beginner-friendly to advanced. I'll cover topics such as Arduino, Proteus Design Suite software, PCB layout designing, telecommunication concepts like Antenna Design, Metamaterials Absorber Design, Wireless Communication, and even MATLAB basics for beginners. Join me on this learning journey and let's explore the fascinating world of electronics and telecommunications together!
Пікірлер
can you share the coding you used? because I had tried once with example code but no work, please share tutorial too
kzread.info/dash/bejne/mGifxo-fgLiwdcY.htmlsi=NNOlekEF0SdJSD0z
How to build this car? Please tell us ❤❤
The HC05 master doesn’t seem to be retaining the role change to 1 but says ok to all steps but the two HC05 don’t seem to connect to each other after completing all the steps
I have tried both modules as master and slave but have the same problem on both not sure what is causing the issue
Antiguo (APIs eliminadas): ledcSetup(R, 5000, 8); // Channel 0 for Motor A, 5 kHz frequency, 8-bit resolution ledcAttachPin(enA, R); ledcSetup(L, 5000, 8); // Channel 0 for Motor A, 5 kHz frequency, 8-bit resolution ledcAttachPin(enB, L); Actualizado (Nueva API): ledcAttachChannel(enA, 5000, 8, R); ledcAttachChannel(enB, 5000, 8, L);
i really appreciate your work.
thank you
𝟓 𝐀𝐫𝐫𝐚𝐲 𝐒𝐞𝐧𝐬𝐨𝐫: kzread.info/dash/bejne/aaqpo9OclsKumrQ.htmlsi=0YVSpWoK0-VGu8fz 𝟔 𝐀𝐫𝐫𝐚𝐲 𝐒𝐞𝐧𝐬𝐨𝐫: kzread.info/dash/bejne/jISp1sihYcbdeKQ.htmlsi=2LRw_1QTJ-SKP5Rj 𝟔 𝐂𝐡𝐚𝐧𝐧𝐞𝐥 𝐋𝐢𝐧𝐞 𝐅𝐨𝐥𝐥𝐨𝐰𝐞𝐫: kzread.info/dash/bejne/hYhsrcaQgLDgoJc.htmlsi=VBM9W-euwMjgoQFj 𝐒𝐨𝐜𝐜𝐞𝐫 𝐁𝐨𝐭 𝐌𝐚𝐤𝐢𝐧𝐠: kzread.info/dash/bejne/oJhhstCnndHbYJc.htmlsi=esh-zakwi_RHr9SC
Do I have to change the ssid and the pasword? Or I keep the same? Because when I put the ip in the browser it doesn´t connect to it
you can change or keep remain same
What joystick are these trying to find the parts just get a lot of controller spares
www.google.com/search?client=ms-android-xiaomi-rvo2&sca_esv=847412b30e358a21&sca_upv=1&sxsrf=ADLYWIKuNA64cqJlr0OiikN2CJk9XXJEqA:1723152699480&q=analog+joystick+arduino&udm=2&fbs=AEQNm0Aa4sjWe7Rqy32pFwRj0UkWd8nbOJfsBGGB5IQQO6L3JyJJclJuzBPl12qJyPx7ESIJKsuo8DSJKOxlDDbn2sXiP2DA1JodL-8OvpqfPcsNcQUuuwc5TAoUZ87rVxy1Xv44fXe4anLnvLcDFC-g4Q79g5ePUy5vwOhyyW06dpaKgZBnQRs&sa=X&ved=2ahUKEwiii6-ErOaHAxXYSmwGHXVuO4EQtKgLegQIGRAB&biw=393&bih=733&dpr=2.75#vhid=NpUU8g3pjMyiQM&vssid=mosaic
How can I connect it to a breadboard?
Don't need to connect in breadboard if you use MB board.
@@aslamhossain1 I need to connect in order to use a Sound buffer alongside the camera
Im already your subcriber but its not downloading code why
Try from computer bro. I've shown in the video
sir it code gives some error Compilation error: 'ledcSetup' was not declared in this scope please help
Maybe you didn't select the proper board. This code is only for esp32.
@@aslamhossain1 thank you sir
Can i use a vero board by cutting it in a rectangular shape
yes
motor rpm, torque, and volt?
600 RPM, 500gm, 12v
Bhaiyya hum yaha pe jyada RGB lights aur transistor badha ke circuit bana sakte hai kya
yeah bana sakte ho
Either it's a blinking LED or the supplied voltage is pulsating voltage source. Just hooking these things up won't result into this.
Fix this error in the code : C:\Users\gplus\Downloads\mywificar\mywificar.ino: In function 'void setup()': C:\Users\gplus\Downloads\mywificar\mywificar.ino:36:3: error: 'ledcSetup' was not declared in this scope 36 | ledcSetup(R, 5000, 8); // Channel 0 for Motor A, 5 kHz frequency, 8-bit resolution | ^~~~~~~~~ C:\Users\gplus\Downloads\mywificar\mywificar.ino:37:3: error: 'ledcAttachPin' was not declared in this scope; did you mean 'ledcAttach'? 37 | ledcAttachPin(enA, R); | ^~~~~~~~~~~~~ | ledcAttach exit status 1 Compilation error: 'ledcSetup' was not declared in this scope
please select proper board. maybe you didn't select the proper board.
How to make this kind of lfr?please make a full Video
InShaAllah
Plz make the video fast
kzread.info/dash/bejne/d4KGqMpxY8uufZs.htmlsi=mYs7UQ4MTdCDblqB
very good❤❤❤🎉
Esp32 connect with relay without bulb please make a vedio
Everything is same bro. You can use any load without bulb.
Unable to open diagram and code link please help
Try from computer or Send a mail on [email protected]
Fast Line Follower Robot এর জন্য ভোল্ট এবং কত RPM এর N20 gear motor ব্যবহার করা উচিত?
12 volt. 600 RPM. er beshi hole torque kome jabe jar karone control kora khub kothin hobe. tai jodi n20 use korte hoi tahole 600 ei better.
@@aslamhossain1 Line Follower এর জন্য N20 এর চেয়ে ভালো কি অন্য কোনো মটর আছে?
Fast Line Follower Robot এর জন্য ভোল্ট এবং কত RPM এর N20 gear motor ব্যবহার করা উচিত?
❤❤❤❤❤
bhai,,lfr er oled display code er tutorial dile valo hobe
InShaAllah
Can you please send the code after subscribe and turn on the bell icon also i did not get the code.
try from computer or send a mail to me: [email protected]
I can't send it it to you I am From India
Please reply
Thank you sir😊😊😊
What is this app called?
github.com/aslam-Hossain-YT/ESP32-Robo-Soccer-Bot/tree/main/Controller%20App
Brother please let us know how do you collect your components? Online or offline? And from which platform or market? Please brother. I am a Mechatronics Technology student. I need build some ptojects like robot, car, drone, robotic arm etc. Please help me. I am from Savar, Dhaka.
Whats app e ekta knock din. 01877543825
@@aslamhossain1 Hae diyechi . Please check.
im getting an error that states "avrdude: stk500_recv()" and I cant figure out what the problem is have you had any experience with this issue?
Port problem. Please select the proper board, processor and port number while uploading the code.
@@aslamhossain1 Is it possible to use an arduino nano with this?
@@makanh.6726 yes. I also used arduino nano
@@aslamhossain1 Did you have any issues with the L298N? When I test it with one side it works fairly fast, when I do it with both sides sometimes I have to give it a little manual turn to start it up and its very slow but a lot of the time it is just not turning. I am not sure whether or not it is a power issue or what. The wiring seems to be perfectly fine.
@@makanh.6726 maybe the pwm value in the enable pins is lower.
1234 the greatest password of all time
🤣 yes
Creative video, thank you :)
Welcome
Can you share your code in chat
What are you using at minute 4:25?
DC Connector for providing power in the driver.
@@aslamhossain1 Thank you!
Saludos te escribí al correo
Can i use 3.7v battery 2
Yes
Please share the code and schematic
Code please 😊
Waiting for Tutorial <3
Please tell how to remove the led Authorization part and directly start the robot moreover please also tell how make the robot such that the robot keeps moving straight even when it is on all white surfaces
sir i am making this but with 8 array sensor and oled display without using buck converter so how can i do this i write a code by myself but the motor is not working please help
You need to contact through whats app
@@aslamhossain1 Sir your whats app
Thank you 😀
Welcome
No code?
I want to discuss some thing with you . can I get your email?
Very cool
Thank you
Bro 220v ki jagah led bulb lga skte h???
You definitely could
Mtlb dc current kaam krega 220v ki jagah?
Use kar sakte ho. Aur power supply be dc hona chaiye
Making video?
Tutorial please sir 😅
🎉🎉🎉, CONG 👌👌👌, code please
Check description
youtube.com/@aryan_gamer144?si=DeD0_e1QwwboGt7h
Code brother