TechShop - Equipment, Tools & Supplies is the automotive industry’s foremost resource. Bringing more than 100,000 shops and technicians the newest products and information they need to stay current with the technology and techniques for success, helping readers get the most out of their tools.
Пікірлер
I can't believe more people don't know about this
Excelente
We've been having nothing but issues with vehicle coverage. We're unable to decode vin on some 4 & 3 year old vehicles such as Ford, GM etc. There are no pending updates on the device. We can't enter the vehicle manually such as the 2021 Ford Explorer or even a 2020 Chevy truck.
what does the peen side do
It doesnt measure pad thickness.
Wow they make a tool for that, I’ve been using a shovel 😂
Useless video
This guy was extremely annoying to watch with his hands waving all over the place. And if it only measures the outside pad that's not really useful information. It's almost always the inside pad that wears out first or has issues.
It doesn’t measure pad thickness, it measures rotor surface evenness. Probably used the rust ring on the outer edge to determine if the rotor is too thin
How do you charge it mine keeps saying low battery and i was never supplied with one just assumed it pulled power from tests
I made one myself.
This is how my cats got stolen
How about for stupid BMW cars that use Lug Studs instead of a traditional lug nut on a stud.
Thank you
What an absolute joke. Literally the only reason I came to check this thing out was for brake pad inspection. It's only checking the outboard pad. Anyone can see tire wear, and see the outer pad.
If the system is too lean would that cause higher fuel consumption than normal?
Yes
Yes, I have a Huge gas Leak full tank wasted it 30 miles
Yes. I have a Rav4... high fuel consumption with -18 of ltft.. clean nozzles ltft now is 4 and fuel consumption are normal
I was curious what this test entails. Thanks for the video!
Can you use other aftermarket or factory sensors other than the Autel 1 sensors with this TPMS tool?
No. Just Autel branded. Maybe OEM if you’re lucky.
You can use ANY brand of pre programmed TPMS
Having to connect to the battery terminals to be able to test a battery that is hidden under a seat or inside the firewall, trunk etc isn't functional. The OBD port should be able to give all info needed, also using the vin number should give the exact battery type and not an extensive list of batteries. I deeply regret buying this product for almost $400 that doesn't deliver much more than a $150 one.
I could have made my millions but they were first , darn ...
Does this model do "battery registration"?
What brands of such, would you recommend?
Worst experience ever they never fixed the issue along with that they kept my vehicle for several days. When I went to pickup my vehicle he gave me a piece of paper and told me take it to Chevy mind you I already paid them $679.00 for them to take my hard earned money what a digrace . I took it to Chevy and was out more money. I called spoke with the manager he then contacted his district manager, he offered me 2 free oil changes mind you they took $679.00 for a service never completed 😒 I reached out again never got a call back from either one. I also contacted customer service support you got it right NOTHING. Do not go there a joke and waste of time and money but I guess this is the Midas way of doing business steal from you and let other dealership fix the problem you paid them to do. If someone know how I can get help with this matter please reach out Please.
I'm on decide if the road. I don't have access to a store to go. Buy a 19 and a 1/2 or an 18 and a 1/2 socket. I need a hack then I can make this 1516 smaller so it will fit properly.
Autel Its600 only can programming for autel tpms sensor other this tool cannot program
not true
Junk. There is no way possible for this tool to accurately measure a rotor. Garbage
I'm trying to understand this tool when you plug it up when searching for The short in the wire when it makes the beeping noise is the fuse connector is telling you that you found the short or it's telling you to reset it... How do you know when you found a short what type of noise does it make
do they have a boot for this?
Yep
I don’t think “extra large head” is much of a selling point for tools intended for tight spots.
i always wanted to work on a car from the next stall over.
I would like to see a demo and also in operation in a working shop . " Where the rubber meets the road " .
i bought a similar product and havent managed to get a single pipe cut with it. just scratches it a bit but refuses to stay in the same spot
It wasn't obvious what sort of probe to use since the secondary voltage is very high and is likely to destroy an ordinary oscilloscope. Also, some instruction on where to put it would be useful.
There isnt a working customer service number for americans to call? Every time i call it either goes to voicemail or my phone provider charges to call china..
What happens if radar has moved location after new bumper install, will recalibration change it to new position. Or do you have to move radar to a new position, hope that makes sense.
The blind spot sensor must be installed in the exact same position as it was from the factory or it will fail calibration. Calibration is required anytime the rear bumper has been removed, collision has occurred, or if the sensor has been replaced.
What brand is this? I have seen many of these but many people complain that they dull quickly. I would like to know the brand and model number of a quality cutter. Thanks
bought one about a year ago and the shaft just broke the other day. Love the quick change blade feature. good power Jumps around some when trying to start cut. Stuck between buying another on or getting my Snap on rebuilt.
I like it, hope they make a 24v version
Glad to hear that! Let's hope!
Why will this tool only diagnose 2016 cars , this is 2022 now and for the cost of this tool it is disgraceful , you are bumping away about this tool but you don’t mention it’s four years out of date, it would fit you better to update it
NICE channel! 😉 👍🏻👍🏻 New SUB BTW!!! Best regards, Patrick
Welcome! We're happy you're here.
CAN SOMEONE PLEASE TELL ME ,, DOES THIS SCAN-TOOL HAVE KEY PROGRAMMING CAPABILITIES ?????????
The Autodiagnos Pro does not currently have key programming capabilities. However, because Continental continues to issue new software updates on a quarterly basis, so there is the possibility that it includes this feature in the future.
Can it do a regeneration?
ESI TO ME HAS ALWAYS BEEN A POSITIVE COMPANY TO BUY ELECTRONIC TEST EQUIPMENT,, AND YES I WILL BE BUYING THIS SOLID AMP-CLAMP !!!!!!!
Awesome! You'll have to post a tool review and tag us!
Why do you not mention it needs a proper alignment? And was that done at the body shop?
Hello Derek, In the interest of video length and focusing on the main procedures we didn’t outwardly mention the alignment, but you are correct in the fact that it is required. One of the beneficial features of Hunter’s ADASLink system is that it guides you through the calibration process, and prior to beginning, there is always a screen that lists any required pre-conditions. In this video, that screen is shown between 3:27 and 3:30, and the alignment is listed along with the other pre-conditions for this specific procedure. It may be easy to miss, but it’s a great point to remember. Also, in this case, we performed the alignment in-house prior to this procedure. Thanks for watching TechShop videos!
😂 ᵖʳᵒᵐᵒˢᵐ
Mark is crushing it.
OBD 1 SCANNER CODE IS 332
Thx I didn't know how Torque Sticks works until now. Which Stick Version is useful when I need at the bolt maximium 100 Nm (metric) (= 885 in lbs) ? Best value 80 Nm (= 700 in-lbs) before I have to use a torque wrench ?
Was that the test? Because it was disappointing
😒 𝓅𝓇o𝓂o𝓈𝓂
That is one slick ratchet how much did it cost you
Who makes these for matco without paying the matco price
Astro, however, I can't find the cobalt ones
@@LuvLivNeverDienope! Matco doesn’t deal with Astro anymore