@1:10 watching them delaminate the roof was bad. I thought watching them advocate a razor blade to cut the sealant from the edge was cringy, but oh my.
@kklonghornsАй бұрын
Waste of time
@carlveilleux5744Ай бұрын
Can an inlet be mounted on the side of a tank or it always must be on the top? Thx!
@ginolevinoАй бұрын
Don't waste your money. Several people tested this and say you get worse mpg and a ton of noise. This doesn't make your truck more aerodynamic, you're adding another surface that creates air turbulence and drag, exactly opposite of what you want
@webguy84973 ай бұрын
Hello how much
@Icondirect3 ай бұрын
Not available! This is a fans decal in support of our racecar driver.
@LovemydogWaylon3 ай бұрын
Wow.
@thomassmith35304 ай бұрын
This is an add not a instructional video don’t waste your time.
@surrealmc6 ай бұрын
could this work for a Tesla Model Y?
@luanne438010 ай бұрын
Where is Icon😉very pretty
@teddy5004 Жыл бұрын
Im trying to figure out how to remove one, i cant seem to remove it without making cuts on the flat iron but id rather not if i dont have to
@Icondirect Жыл бұрын
The attachment of the tanks vary a bit from the original trailer manufacturers. Often they are slid on and clamped in such a way that they can be removed easily, but sometimes they are put on early in the manufacturing process and stuff gets built around them making it rather difficult. It varies, so I'm sorry I can't give specific advice.
@teddy5004 Жыл бұрын
@@Icondirect That's what it seems like here! The technician who was teaching me couldn't figure it out so he had 5 other techs look at it and we all settled on an angle grinder being the solution. We put it back together in a way the next person can easily remove it if they need to
@Icondirect Жыл бұрын
@@teddy5004 Good thing to think forward that way! Happy you got it sorted!
@KoiAquaponics Жыл бұрын
I wonder if i have the wrong router, mine is 15amp but I've used 3" and 4" fittings and it just heats up and sticks and it forces the router to stop, end up with half assed welds with no proper puddles.
@infoicon704 Жыл бұрын
We recommend using a router that has 1.5 - 2 horsepower. It should be capable of spinning with 15,000 to 25,000 rpm. For fittings with a larger diameter, you might need to have a stronger router even.
@BabyBunch Жыл бұрын
I thought the pull valve was at the end of the pipes
@Icondirect Жыл бұрын
An RV's gate valve location can vary depending on the setup. It can be deceptive, because the handle is also extendable and can be quite accessible, even if the valve is far under the RV. There can also be multiple valves to facilitate the black & grey tanks draining to one point. Sometimes the valve is located closer to the drain end & sometimes there's 2 so you can isolate the drain segment if needed.
@KoiAquaponics Жыл бұрын
Is it possible to spin weld onto a cylinder tank or just flat tanks?
@Icondirect Жыл бұрын
Depending on the degree of the curvature and the skill/experience of the installer - it could be possible. It's always recommended that you have as flat of a surface as possible, however. We install fittings on some curved faces regularly - but with experienced installers. Here is an example: www.icondirect.com/fresh-water-tank-wt3796-118-gal/
@adrianruiz8690 Жыл бұрын
Okay but why is this small peace of plastic over 100$
@Icondirect Жыл бұрын
Our aftermarket AC shrouds are made of a High Density poly to provide a long life. This premium material is a consideration made to prevent RV owners having to replace the AC Shroud multiple times with the OEM version due to weather events and UV Damage. This, along with other design factors contributes to it's price.
@lesliedrager5593 Жыл бұрын
What size screws should I use?
@Icondirect Жыл бұрын
We recommend this or equivalent: www.icondirect.com/skylight-installation-screws-20-pc/
@chadjones992 жыл бұрын
shes says fuel prices are not getting better ... WOW was she right its 2022 and wow
@Icondirect Жыл бұрын
What is the saying? Something like: "Best time to get an Aeroshield was 10 years ago. The Second best time is now."
@chadjones99 Жыл бұрын
@@Icondirect lol I just bought one a few weeks ago, seeing about 1 mpg increase and half as many bugs on rv
@delisadabney75382 жыл бұрын
Thank you so much for this valuable, helpful information.
@Icondirect2 жыл бұрын
Glad it was helpful!
@blq242 жыл бұрын
Great VIB BUT ....STOP THAT MUSIC!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
@Icondirect2 жыл бұрын
I understand where you are coming from. With the annotated steps, you could mute and follow along!
@realJimMarshall Жыл бұрын
No. Make the music louder. This is my jam.
@moises303212 жыл бұрын
Do trailers need this, or can I remove it? I’m permanently connected to city water & I’m remodeling to make the living area larger, & the water storage take is kinda in the way
@Icondirect2 жыл бұрын
A fresh water tank can be set up to be bypassed, as well as completely removed.
@imwithstupid5052 жыл бұрын
SO helpful. Been researching for an hour and you just answered all of my questions. Thank you!
@deborahhopkinson52432 жыл бұрын
Um, you didn't get to the install. Perhaps, rename the video or include the install? Did not subscribe for this reason. Thank you.
@Icondirect2 жыл бұрын
Hi Deborah! Installations vary so much, we wanted to focus on explaining best practices in selecting the appropriate tank and touching on installation in a general sense. Starting at 2:22 we discuss and show physically placing and supporting the tank.
@deborahhopkinson52432 жыл бұрын
@@Icondirect, thank you for your response. As you stated, this is a general information video, not an install. I'm trying to figure out the plumbing aspect (the actual install,) especially when the original tank is no longer being manufactured. Does the same shape and size need to be installed because of weight distribution? What type of fittings/tubing should be used? Type of sealant and where? What if the fittings don't line up? How is that addressed? I'm finding a lot of 'Southern Engineering' videos from other people just trying to get it done, and partial/hollow advice from RV places that don't want people doing their own repairs; this half-a**, good-enough attitude is why these things have to be repaired all the time in the first place. The last time anyone took quality work seriously (as a normal way of doing business,) was 1973, but I can't find a seventy-year-old RV repair technician. I have been taken advantage of by RV shops (almost) every time, so I won't do that anymore. I'll learn how to do it myself, or it won't get done. I'll keep looking; thank you.
@Icondirect2 жыл бұрын
Hey Deborah, The factors involved with plumbing in the tank can vary wildly and wasn't the focus of this video because of that. I'll try help with a few of your questions: Does the same shape and size need to be installed because of weight distribution? Typically, No. You can upgrade the tank size to whatever space you have available or downsize. What type of fittings/tubing should be used? Type of sealant and where? Modern fresh water systems is typically done with PEX. 1/2" sized piping is most common, with 3/8" also being acceptable. Type of sealant and where? Typically plumbers tape can be used on threaded fitting locations. Otherwise pipe connections via PEX connections is typical. Sealant isn't often used. What if the fittings don't line up? Fitting locations on the tank can vary. Aftermarket configurations from ICON usually entail a fill and 3 1/2" fittings on the end. One will typically be used to vent the tank, one will supply the pump. The 3rd and 4th can either serve as a drain if desired. Unused fittings can be plugged. As far as lining things up, you'll want to plan out where the pump is and the lengths of pex. Giving slightly additional length with PEX is easy and desirable as you can then easily loop the piping and line them up at each end easily. I hope this helps!
@alfnoakes3922 жыл бұрын
Am building a 'cockpit' for a 'dog-pram' (stroller pram to be used for elderly dog now it is no longer needed for kids) out of ABS sheet (largest thing Ive built from ABS) so this instruction video is well-timed ... Thanks
@BLAIRMURPHY182 жыл бұрын
Love Amber as a driver. Support her by joining our Facebook Fan group/Club Called- Amber Balcaen NASCAR’s Next Generation Fan Club. Come join us now! We are a new group!
@debbiewollard90562 жыл бұрын
I got the replacement shroud that looks like the one you removed - comes in two parts - and am trying to assemble the two parts - any tricks for that ? LOl - I haven't even gotten to installing it on my roof yet. Thank you -
@infoicon7042 жыл бұрын
Good morning Debbie, Thank you for contacting us! For the shroud you purchased, it would be a replacement for that two piece option that you currently have. You would need to remove the bottom grey pan and our replacement shroud would replace both pieces. Feel free to let me know if you have further questions! Thank you, Heidi.
@wingman12552 жыл бұрын
Thank you very much. Very generous of you.
@tonioval2 жыл бұрын
Hi, thanks for the video. I am wondering why if you cut off the old sealant, you didn't apply new sealant? Is it not necessary? I am planning to install one myself and I want to do it right. Thank you again.
@Icondirect2 жыл бұрын
The Rubber gasket should do all of the sealing required, but it would not hurt to apply some external grade silicone around the edge if you desire.
@starbittrune2 жыл бұрын
I didn't see the sealant application in the video. What sealant did you use, and when in the process is it applied? Also, what type of screws are recommended? (Aluminum? Stainless? Thread/size?)
@Icondirect2 жыл бұрын
A clear (or appropriately colored) exterior silicone was used here after the installation. Not entirely necessary, but can finish off the look nicely. For screws, we have some offered for this explicit purpose & they are described here: www.icondirect.com/painted-installation-screws-15-pc/
@stebro27382 жыл бұрын
Just a question.. Why would you remove the Insulating inner dome ?? Don't you have a new one available or a way to re-use the old one with your new bezel?? Skylites create a LOT of heat gain, the proof is in the many products just to stop that heat from coming in.. It seems like if you've got a ready made insulator.......
@Icondirect2 жыл бұрын
In the video we do show the installation of an inner dome and then also show the installation of just a garnish. The option is available to keep the inner layer for insulation properties, but we showed also the installation of the trimmable garnish for situations where that may be appropriate. Definitely agree with you that the inner dome is preferred most of the time.
@stebro27382 жыл бұрын
@@Icondirect Thanks forthe answer.. I've been camping fortoo many years....
@Curb712 жыл бұрын
How does the tape provide a cushion? I don't understand the purpose of wrapping tape around the drill bit. Aren't you screwing the new one into the existing holes in the sheet metal?
@Icondirect2 жыл бұрын
Hi Steve, It is to provide a cushioned stopping point as you drill new pilot holes into the sheet metal of the RV. The existing holes do not always line up perfectly, as was the case here.
@christiancarver3142 жыл бұрын
Love these questions you put together for Amber
@yankeesusa12 жыл бұрын
What size is that mini pry bar?
@Icondirect2 жыл бұрын
Hey Jaz, Looks to be 2 or 3" wide pry bar, though that isn't necessary. Later in the video Howard is shown using a little homemade scraper, which is just a piece of plastic with a beveled edge. That also does the trick.
@christiancarver3143 жыл бұрын
Loved yall having Amber featured in yalls video. And I wish her the best of luck in her racing career as she climbs the racing ladder😊😊
@dodicoral99943 жыл бұрын
slcfk vum.fyi
@scottisaaks3 жыл бұрын
Hardest part is removing the sealant it's like gum.. goo gone work?
@infoicon7043 жыл бұрын
Hi Scott, Depending on the surface of the roof, chemicals like goo gone can actually do way much more damage than help. We found the best way is to use the way we did it in the video, using a heat gun and a plastic putty knife. You want to be careful not to damage the rubber roof membrane which is on most of the RVs.
@terryruggiero1718 Жыл бұрын
I found Dicor roof cleaner helpful in removing lap sealant because unlike silicone, complete removal from the roof is not necessary to create a new seal. Lapse sealant will adhere to itself it just needs to be cleaned well before putting the new layer on.
@johnmclaren7059 Жыл бұрын
My buddy is a red seal rv tech he did my skylight and uses lighter fluid to clean it
@70ixlr8629 күн бұрын
@@terryruggiero1718 Dicor does mention mineral spirits (it works well ) Cracking and brittle Lap sealant should be removed depending on characteristics it is showing, mostly dependent on age and environmental effects. Once it becomes hard, the removal process requires longer chemical (mineral spirit compress) and physical removal. It is a walk in the park to remove before it becomes a cracked skin mess with multiple layers of random sealants.
@0646246503 жыл бұрын
So helpful!
@geraldstubbe58843 жыл бұрын
Hmm do an image search on this seal and it shows the glass going in the wider channel. There are four ways you can put this seal in and three are wrong. There are conflicting images.
@Icondirect3 жыл бұрын
It varies depending on the material thickness. We have actually made a change to this and you are correct. We need to update the video with an annotation once i've confirmed the details.
@aladyontheverge3 ай бұрын
@@Icondirect Did you update the video?
@420broccoli3 жыл бұрын
will these also fit in the ECO royal featherlite? I believe theyre from identical molds...
@infoicon7043 жыл бұрын
Would we be able to start a conversation on our website? Feel free to go onto our website for information as to how to contact us. You can use our texting platform or send us an email. If you could send us pictures of your RV window that you would like to replace, that would be great! Ask for Heidi and I will be happy to assist you! Thank you and I look forward to hearing from you.
@LazjoeS3 жыл бұрын
I guess I missed the step in the video to check if the protective film is wrapped around the bottom side before slapping the skylight down into your nice even bead of sealant. I would suggest you mention that.
@Icondirect3 жыл бұрын
Hi LazjoeS, Thank you for the feedback. I'll see about annotating the video as best we can with that note.
@deborahbates-ec6vq Жыл бұрын
😊
@JBK64710 ай бұрын
No such annotation found. Peeling not pealing.@@Icondirect
@kenyanwashington3 жыл бұрын
Great news
@zach1010103 жыл бұрын
I think you must of skipped the parts where windows pop out and plenty of swearing takes place... great video!
@alex-anneboisjoly59873 жыл бұрын
Is it possible to know where did you get it? The rubber! Please :)
@Icondirect3 жыл бұрын
The gasket is available, along with the window here: www.icondirect.com/boler-window-with-locking-gasket/. We don't recommend the replacement of just the gasket. Usually, if the gasket is in rough shape, the original plastic window is due for an upgrade as well.
@davidcrawford65053 жыл бұрын
I'd like to replace with one that opens. This is a stupid idea from FR.
@SwastikaHinduSansrkit3 жыл бұрын
I agree. The skylight in an RV will just bake the interior further needing to pump your AC unit harder and draining the batteries or peaking the inverter. Its better to have a roof vent. Fun Tastic is a good brand. You get the light needed , yet the fan and manual accessibility to open and close as wish with a crank.
@yankeesusa12 жыл бұрын
Will these end up getting yellow again? Are there some that are stronger than others so i replace it less or it lasts longer?
@terryruggiero1718 Жыл бұрын
@@yankeesusa1 I just bought a replacement skylight from skylight depot and it is thicker than the original thus sturdier.
@JBK64710 ай бұрын
Use a tinted one.@@yankeesusa1
@Chessiegal6 жыл бұрын
I don't see where the SUCTION CUPS are suppose to go? What am I missing?
@Icondirect6 жыл бұрын
Hi Sheri, The Suction cups are below the base; it's what the aeroshield sits on to protect the roof of the truck. You can see them very briefly as the shield is lifted into place at 2:20
@puronica646 жыл бұрын
I need one for my semi truck, do you sell them for semis? or do you know where I can get one?
@Icondirect6 жыл бұрын
Hi Michael, The AeroShield is designed for the RV and Cargo Trailer market - at this time we do not have a design for commercial semi trucks. I'm not certain where I could send you either. I do see them around - so they must be found somewhere. Sorry I can't be of more help! --jordan
@crfendr39077 жыл бұрын
Hi i have a 2016 Chev Equinox will it fit on my SUV
@Icondirect7 жыл бұрын
Please call 1-888-362-4266 to discuss your fitment with a representative.
@TheGbortnick9 жыл бұрын
I have this air deflector and am using it with a 2014 F 150 ford with 6 6 bed with a hard flat cover over the bed. Tried on roof but very noisy . Am trying it now on the hard flat bed cover. Am pulling a tr and it feels like pulling a wall through the air. Got any suggestions for placement of the wing.
@Icondirect9 жыл бұрын
George Bortnick Hi George! Sorry about our delay in seeing this comment! One recommendation that cuts down on air noise while on the roof is to do a full turn on the straps. Typically any noise issues are from those flapping and vibrating in the wind. Having a twist in there alleviates that. Usually you want the deflector as close to the trailer as possible, so I would recommend trying to mount it on the flat cover in some manner.
@joycesrvlegacy-46356 жыл бұрын
I have same Ford...I wondered about whistling from the air gap caused by the strap. How would you go about "twisting"?
@Icondirect6 жыл бұрын
Basically, before hooking the hook into the door area and tightening the straps, flip the hooks over once completely. Then there's a bit of a twhirl in the strap between the hook and the deflector base.
@lordcam111 жыл бұрын
I KNOW THAT GUY!
@chinlbc15 жыл бұрын
im going to install this on my 94 honda civic hatchback
Пікірлер
how do you open the hole for inlet ?
@1:10 watching them delaminate the roof was bad. I thought watching them advocate a razor blade to cut the sealant from the edge was cringy, but oh my.
Waste of time
Can an inlet be mounted on the side of a tank or it always must be on the top? Thx!
Don't waste your money. Several people tested this and say you get worse mpg and a ton of noise. This doesn't make your truck more aerodynamic, you're adding another surface that creates air turbulence and drag, exactly opposite of what you want
Hello how much
Not available! This is a fans decal in support of our racecar driver.
Wow.
This is an add not a instructional video don’t waste your time.
could this work for a Tesla Model Y?
Where is Icon😉very pretty
Im trying to figure out how to remove one, i cant seem to remove it without making cuts on the flat iron but id rather not if i dont have to
The attachment of the tanks vary a bit from the original trailer manufacturers. Often they are slid on and clamped in such a way that they can be removed easily, but sometimes they are put on early in the manufacturing process and stuff gets built around them making it rather difficult. It varies, so I'm sorry I can't give specific advice.
@@Icondirect That's what it seems like here! The technician who was teaching me couldn't figure it out so he had 5 other techs look at it and we all settled on an angle grinder being the solution. We put it back together in a way the next person can easily remove it if they need to
@@teddy5004 Good thing to think forward that way! Happy you got it sorted!
I wonder if i have the wrong router, mine is 15amp but I've used 3" and 4" fittings and it just heats up and sticks and it forces the router to stop, end up with half assed welds with no proper puddles.
We recommend using a router that has 1.5 - 2 horsepower. It should be capable of spinning with 15,000 to 25,000 rpm. For fittings with a larger diameter, you might need to have a stronger router even.
I thought the pull valve was at the end of the pipes
An RV's gate valve location can vary depending on the setup. It can be deceptive, because the handle is also extendable and can be quite accessible, even if the valve is far under the RV. There can also be multiple valves to facilitate the black & grey tanks draining to one point. Sometimes the valve is located closer to the drain end & sometimes there's 2 so you can isolate the drain segment if needed.
Is it possible to spin weld onto a cylinder tank or just flat tanks?
Depending on the degree of the curvature and the skill/experience of the installer - it could be possible. It's always recommended that you have as flat of a surface as possible, however. We install fittings on some curved faces regularly - but with experienced installers. Here is an example: www.icondirect.com/fresh-water-tank-wt3796-118-gal/
Okay but why is this small peace of plastic over 100$
Our aftermarket AC shrouds are made of a High Density poly to provide a long life. This premium material is a consideration made to prevent RV owners having to replace the AC Shroud multiple times with the OEM version due to weather events and UV Damage. This, along with other design factors contributes to it's price.
What size screws should I use?
We recommend this or equivalent: www.icondirect.com/skylight-installation-screws-20-pc/
shes says fuel prices are not getting better ... WOW was she right its 2022 and wow
What is the saying? Something like: "Best time to get an Aeroshield was 10 years ago. The Second best time is now."
@@Icondirect lol I just bought one a few weeks ago, seeing about 1 mpg increase and half as many bugs on rv
Thank you so much for this valuable, helpful information.
Glad it was helpful!
Great VIB BUT ....STOP THAT MUSIC!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
I understand where you are coming from. With the annotated steps, you could mute and follow along!
No. Make the music louder. This is my jam.
Do trailers need this, or can I remove it? I’m permanently connected to city water & I’m remodeling to make the living area larger, & the water storage take is kinda in the way
A fresh water tank can be set up to be bypassed, as well as completely removed.
SO helpful. Been researching for an hour and you just answered all of my questions. Thank you!
Um, you didn't get to the install. Perhaps, rename the video or include the install? Did not subscribe for this reason. Thank you.
Hi Deborah! Installations vary so much, we wanted to focus on explaining best practices in selecting the appropriate tank and touching on installation in a general sense. Starting at 2:22 we discuss and show physically placing and supporting the tank.
@@Icondirect, thank you for your response. As you stated, this is a general information video, not an install. I'm trying to figure out the plumbing aspect (the actual install,) especially when the original tank is no longer being manufactured. Does the same shape and size need to be installed because of weight distribution? What type of fittings/tubing should be used? Type of sealant and where? What if the fittings don't line up? How is that addressed? I'm finding a lot of 'Southern Engineering' videos from other people just trying to get it done, and partial/hollow advice from RV places that don't want people doing their own repairs; this half-a**, good-enough attitude is why these things have to be repaired all the time in the first place. The last time anyone took quality work seriously (as a normal way of doing business,) was 1973, but I can't find a seventy-year-old RV repair technician. I have been taken advantage of by RV shops (almost) every time, so I won't do that anymore. I'll learn how to do it myself, or it won't get done. I'll keep looking; thank you.
Hey Deborah, The factors involved with plumbing in the tank can vary wildly and wasn't the focus of this video because of that. I'll try help with a few of your questions: Does the same shape and size need to be installed because of weight distribution? Typically, No. You can upgrade the tank size to whatever space you have available or downsize. What type of fittings/tubing should be used? Type of sealant and where? Modern fresh water systems is typically done with PEX. 1/2" sized piping is most common, with 3/8" also being acceptable. Type of sealant and where? Typically plumbers tape can be used on threaded fitting locations. Otherwise pipe connections via PEX connections is typical. Sealant isn't often used. What if the fittings don't line up? Fitting locations on the tank can vary. Aftermarket configurations from ICON usually entail a fill and 3 1/2" fittings on the end. One will typically be used to vent the tank, one will supply the pump. The 3rd and 4th can either serve as a drain if desired. Unused fittings can be plugged. As far as lining things up, you'll want to plan out where the pump is and the lengths of pex. Giving slightly additional length with PEX is easy and desirable as you can then easily loop the piping and line them up at each end easily. I hope this helps!
Am building a 'cockpit' for a 'dog-pram' (stroller pram to be used for elderly dog now it is no longer needed for kids) out of ABS sheet (largest thing Ive built from ABS) so this instruction video is well-timed ... Thanks
Love Amber as a driver. Support her by joining our Facebook Fan group/Club Called- Amber Balcaen NASCAR’s Next Generation Fan Club. Come join us now! We are a new group!
I got the replacement shroud that looks like the one you removed - comes in two parts - and am trying to assemble the two parts - any tricks for that ? LOl - I haven't even gotten to installing it on my roof yet. Thank you -
Good morning Debbie, Thank you for contacting us! For the shroud you purchased, it would be a replacement for that two piece option that you currently have. You would need to remove the bottom grey pan and our replacement shroud would replace both pieces. Feel free to let me know if you have further questions! Thank you, Heidi.
Thank you very much. Very generous of you.
Hi, thanks for the video. I am wondering why if you cut off the old sealant, you didn't apply new sealant? Is it not necessary? I am planning to install one myself and I want to do it right. Thank you again.
The Rubber gasket should do all of the sealing required, but it would not hurt to apply some external grade silicone around the edge if you desire.
I didn't see the sealant application in the video. What sealant did you use, and when in the process is it applied? Also, what type of screws are recommended? (Aluminum? Stainless? Thread/size?)
A clear (or appropriately colored) exterior silicone was used here after the installation. Not entirely necessary, but can finish off the look nicely. For screws, we have some offered for this explicit purpose & they are described here: www.icondirect.com/painted-installation-screws-15-pc/
Just a question.. Why would you remove the Insulating inner dome ?? Don't you have a new one available or a way to re-use the old one with your new bezel?? Skylites create a LOT of heat gain, the proof is in the many products just to stop that heat from coming in.. It seems like if you've got a ready made insulator.......
In the video we do show the installation of an inner dome and then also show the installation of just a garnish. The option is available to keep the inner layer for insulation properties, but we showed also the installation of the trimmable garnish for situations where that may be appropriate. Definitely agree with you that the inner dome is preferred most of the time.
@@Icondirect Thanks forthe answer.. I've been camping fortoo many years....
How does the tape provide a cushion? I don't understand the purpose of wrapping tape around the drill bit. Aren't you screwing the new one into the existing holes in the sheet metal?
Hi Steve, It is to provide a cushioned stopping point as you drill new pilot holes into the sheet metal of the RV. The existing holes do not always line up perfectly, as was the case here.
Love these questions you put together for Amber
What size is that mini pry bar?
Hey Jaz, Looks to be 2 or 3" wide pry bar, though that isn't necessary. Later in the video Howard is shown using a little homemade scraper, which is just a piece of plastic with a beveled edge. That also does the trick.
Loved yall having Amber featured in yalls video. And I wish her the best of luck in her racing career as she climbs the racing ladder😊😊
slcfk vum.fyi
Hardest part is removing the sealant it's like gum.. goo gone work?
Hi Scott, Depending on the surface of the roof, chemicals like goo gone can actually do way much more damage than help. We found the best way is to use the way we did it in the video, using a heat gun and a plastic putty knife. You want to be careful not to damage the rubber roof membrane which is on most of the RVs.
I found Dicor roof cleaner helpful in removing lap sealant because unlike silicone, complete removal from the roof is not necessary to create a new seal. Lapse sealant will adhere to itself it just needs to be cleaned well before putting the new layer on.
My buddy is a red seal rv tech he did my skylight and uses lighter fluid to clean it
@@terryruggiero1718 Dicor does mention mineral spirits (it works well ) Cracking and brittle Lap sealant should be removed depending on characteristics it is showing, mostly dependent on age and environmental effects. Once it becomes hard, the removal process requires longer chemical (mineral spirit compress) and physical removal. It is a walk in the park to remove before it becomes a cracked skin mess with multiple layers of random sealants.
So helpful!
Hmm do an image search on this seal and it shows the glass going in the wider channel. There are four ways you can put this seal in and three are wrong. There are conflicting images.
It varies depending on the material thickness. We have actually made a change to this and you are correct. We need to update the video with an annotation once i've confirmed the details.
@@Icondirect Did you update the video?
will these also fit in the ECO royal featherlite? I believe theyre from identical molds...
Would we be able to start a conversation on our website? Feel free to go onto our website for information as to how to contact us. You can use our texting platform or send us an email. If you could send us pictures of your RV window that you would like to replace, that would be great! Ask for Heidi and I will be happy to assist you! Thank you and I look forward to hearing from you.
I guess I missed the step in the video to check if the protective film is wrapped around the bottom side before slapping the skylight down into your nice even bead of sealant. I would suggest you mention that.
Hi LazjoeS, Thank you for the feedback. I'll see about annotating the video as best we can with that note.
😊
No such annotation found. Peeling not pealing.@@Icondirect
Great news
I think you must of skipped the parts where windows pop out and plenty of swearing takes place... great video!
Is it possible to know where did you get it? The rubber! Please :)
The gasket is available, along with the window here: www.icondirect.com/boler-window-with-locking-gasket/. We don't recommend the replacement of just the gasket. Usually, if the gasket is in rough shape, the original plastic window is due for an upgrade as well.
I'd like to replace with one that opens. This is a stupid idea from FR.
I agree. The skylight in an RV will just bake the interior further needing to pump your AC unit harder and draining the batteries or peaking the inverter. Its better to have a roof vent. Fun Tastic is a good brand. You get the light needed , yet the fan and manual accessibility to open and close as wish with a crank.
Will these end up getting yellow again? Are there some that are stronger than others so i replace it less or it lasts longer?
@@yankeesusa1 I just bought a replacement skylight from skylight depot and it is thicker than the original thus sturdier.
Use a tinted one.@@yankeesusa1
I don't see where the SUCTION CUPS are suppose to go? What am I missing?
Hi Sheri, The Suction cups are below the base; it's what the aeroshield sits on to protect the roof of the truck. You can see them very briefly as the shield is lifted into place at 2:20
I need one for my semi truck, do you sell them for semis? or do you know where I can get one?
Hi Michael, The AeroShield is designed for the RV and Cargo Trailer market - at this time we do not have a design for commercial semi trucks. I'm not certain where I could send you either. I do see them around - so they must be found somewhere. Sorry I can't be of more help! --jordan
Hi i have a 2016 Chev Equinox will it fit on my SUV
Please call 1-888-362-4266 to discuss your fitment with a representative.
I have this air deflector and am using it with a 2014 F 150 ford with 6 6 bed with a hard flat cover over the bed. Tried on roof but very noisy . Am trying it now on the hard flat bed cover. Am pulling a tr and it feels like pulling a wall through the air. Got any suggestions for placement of the wing.
George Bortnick Hi George! Sorry about our delay in seeing this comment! One recommendation that cuts down on air noise while on the roof is to do a full turn on the straps. Typically any noise issues are from those flapping and vibrating in the wind. Having a twist in there alleviates that. Usually you want the deflector as close to the trailer as possible, so I would recommend trying to mount it on the flat cover in some manner.
I have same Ford...I wondered about whistling from the air gap caused by the strap. How would you go about "twisting"?
Basically, before hooking the hook into the door area and tightening the straps, flip the hooks over once completely. Then there's a bit of a twhirl in the strap between the hook and the deflector base.
I KNOW THAT GUY!
im going to install this on my 94 honda civic hatchback