This is a very good video in regard to actually showing the steps you took. And how you actually put the wires back together.
@SimmyBowman2 ай бұрын
Great video. 🫵😎🫵 Really appreciate it !!! Thx
@AntonRu2 ай бұрын
my motor cable is stuck due to some white silicon and out ng es no getting it out without a BIG fight
@01JetMan3 ай бұрын
Thank you. So one of my hub motor wires got cut and I have no throttle response. I don't know if running the bike previously with wire cut destroyed the controller or just hub motor.
@user-rc2mq6uf1b7 ай бұрын
Informative vid thank you. What type of cable did you use as a replacement, what gauge was it?
@picwick57 Жыл бұрын
I took my wheel apart to do the same repair. I had no power to my blue phase wire using power tester same motor as what you worked on. now it's apart & i have continuity on all the wires so it could be in the rotor winding??
@MakerPR Жыл бұрын
Hi - Do you have a link for the "tree clamp"? Did I spell it correctly? Thanks!
@mateuszkubala1800 Жыл бұрын
I might need to do this soon. My wires are on the end of their life. The part of my bike frame which holds the wheel axle, got so bent open, this twisted the wires almost enough to rip them out. Bad design of the bike frame, not designed to be modded into an ebike.
@sigma_799 Жыл бұрын
I didn’t get any punctures on my fat bike. maybe my tyres are thick too
@danbrikco143 Жыл бұрын
I’ve been looking at all videos about rewiring e-bike hub motors & can’t find 1 which shows exactly where each phase wire attaches inside the hub. Obviously like for like reattachment as per hall sensor wiring but my problem is that i had an axle spinout on my Dapu M155, after which the motor has not worked. the yellow phase wire is not attached....display shows o.o speed and PAS 0. the lights also won’t switch on; after 10mins the display shows 33 the switches off...any ideas appreciated category: dapu m155 rear disk brake gearbox: planetary gearbox with freewheel type: bldc motor (brushless direct current) power: nominal 250 w (maximal 400 w for rotation sensor, 500 w for torque sensor) used bb set: ncte sbbrf - rotation sensor ncte sbbrt - torque-rotation sensor
@user-gx4mz9so3g Жыл бұрын
Are all motors cables 9 pins and what the 7 pins functions beside the vdc+ and GND, I need to remove my disc break and there no way without cutting the motor cable a otherwise I need to remove the battery case. How it should be done? Should I cut it and reconnect it?
@robertmotion Жыл бұрын
Great video. Question. My ebike works fine, but when I do the motor phase wire test and turn wheel (backwards) for resistance I don't get any but motor works fine and hall sensors work fine. This is not normal but it hasn't caused problems. And ideas why? /bklyn 👑
@trevorjames5493 Жыл бұрын
I just needed to see how to remove the wires from the inside the axel but you completely skipped that part so maybe I'll just pull on it harder lol thanks
@wallstbets48652 жыл бұрын
i dont think we going to get any answers this guy is gone.
@d.powers58272 жыл бұрын
Can you show me how to fix mine for my electric pride fat tire e bike....got few rips in my wire
@Keeganismyfirstname2 жыл бұрын
Hey does anyone know what those wires are called? My wires got stripped near the axle and i can't buy the wire without the motor..I know its the phase wire but I can't find any online for a brushless motor..
@joeaverager2 жыл бұрын
Where can I source the wire?
@robertnitschke892 жыл бұрын
Where did you get the wire? You can't repair these motors because no one knows where to get the wire?
@francescocaravella45562 жыл бұрын
I'd suggest use a waterproof cable you can buy an extension and cut off what you need
@lukedodson34412 жыл бұрын
Where can I get one of those clamps?
@jakeb17782 жыл бұрын
Where can I buy replacement cable?
@mikekirtley48222 жыл бұрын
Excellent video very well explained,thank you .
@BillFromHalifax3 жыл бұрын
Nice video man! 👍🏻 I wonder if Daymak hub motors are this easy!
@joehozzy26163 жыл бұрын
Great video. Have you ever rewired a geared hub motor? Thanks
@milestone_achiever46343 жыл бұрын
Hi. Are you based in the U.S.? Do you have a bike shop? I have the same problem. My hub motor cables are ruined primarily because I have been riding without a torque arm. The rear hub motor twisted sometimes while I was riding and ruined the hub motor wires I had a very hard time finding a torque arm in bike stores
@rjbikes12372 жыл бұрын
Yeah same it happens to me I only have 2 wires connected now very sketchy but now I’m gonna open it and connected it back
@shaochen19803 жыл бұрын
Which brand and model of tire?
@bobjerome53903 жыл бұрын
hi worked on brother ebikes so many time the cable is the main thing on ebikes that goes bad tip you will need to save up for cells over time s the life of them goes down over time
@esoteric_Derek3 жыл бұрын
Thank you. I hope my repair goes as smooth as yours seemed to.
@rogerbarnett85713 жыл бұрын
Thanks , just what I needed !
@SALEH_4K_POV3 жыл бұрын
Hi where do you buy the replacement wire and what is the replacement wire called also the connectors to the replacement wire?
@chiwahliu74473 жыл бұрын
It all depends on your motor. In my case, I just cut it down so I didn't but new wire
@thomashamilton45793 жыл бұрын
what wire did you replace that with?
@electricbikediy77603 жыл бұрын
I'm not clear. Replace what?
@thomashamilton45793 жыл бұрын
the replacement Gage wire
@electricbikediy77603 жыл бұрын
I used 12awg wire
@johjohjones82493 жыл бұрын
I have blow my controller an the bk wheel gone lumpy an will not spin on its own
@BooYaa699 жыл бұрын
Im thinking of getting this bike too! Yes anything over 15mph is illegal as you would need MOT, license and insurance. Just get a Dahon p8 and motorize it using the magic pie 3 kits and convert it yourself. That's what im gona do!
@Martins20129 жыл бұрын
BooYaa69 I have the same project as you. Dahon jetstream 8 and magic pie 3 or bafang 8 mid drive! what do you think of bafang mid drive?? its lighter then magic pie thou...
@peschanyj9 жыл бұрын
There are so few full suspension folding bikes on the market! But it's necessary for high speeds that electrodrive provides. So Dahon's bike is one of a few to choose from. Good-looking one). Btw, do you remove batteries when fold the bike? If yes, is it fast and easy?
@gulibuf10 жыл бұрын
hey, thats cool! did you convert the bike? isnt it ileagal in UK more than 250W?lol
Пікірлер
This helps thanks
This is a very good video in regard to actually showing the steps you took. And how you actually put the wires back together.
Great video. 🫵😎🫵 Really appreciate it !!! Thx
my motor cable is stuck due to some white silicon and out ng es no getting it out without a BIG fight
Thank you. So one of my hub motor wires got cut and I have no throttle response. I don't know if running the bike previously with wire cut destroyed the controller or just hub motor.
Informative vid thank you. What type of cable did you use as a replacement, what gauge was it?
I took my wheel apart to do the same repair. I had no power to my blue phase wire using power tester same motor as what you worked on. now it's apart & i have continuity on all the wires so it could be in the rotor winding??
Hi - Do you have a link for the "tree clamp"? Did I spell it correctly? Thanks!
I might need to do this soon. My wires are on the end of their life. The part of my bike frame which holds the wheel axle, got so bent open, this twisted the wires almost enough to rip them out. Bad design of the bike frame, not designed to be modded into an ebike.
I didn’t get any punctures on my fat bike. maybe my tyres are thick too
I’ve been looking at all videos about rewiring e-bike hub motors & can’t find 1 which shows exactly where each phase wire attaches inside the hub. Obviously like for like reattachment as per hall sensor wiring but my problem is that i had an axle spinout on my Dapu M155, after which the motor has not worked. the yellow phase wire is not attached....display shows o.o speed and PAS 0. the lights also won’t switch on; after 10mins the display shows 33 the switches off...any ideas appreciated category: dapu m155 rear disk brake gearbox: planetary gearbox with freewheel type: bldc motor (brushless direct current) power: nominal 250 w (maximal 400 w for rotation sensor, 500 w for torque sensor) used bb set: ncte sbbrf - rotation sensor ncte sbbrt - torque-rotation sensor
Are all motors cables 9 pins and what the 7 pins functions beside the vdc+ and GND, I need to remove my disc break and there no way without cutting the motor cable a otherwise I need to remove the battery case. How it should be done? Should I cut it and reconnect it?
Great video. Question. My ebike works fine, but when I do the motor phase wire test and turn wheel (backwards) for resistance I don't get any but motor works fine and hall sensors work fine. This is not normal but it hasn't caused problems. And ideas why? /bklyn 👑
I just needed to see how to remove the wires from the inside the axel but you completely skipped that part so maybe I'll just pull on it harder lol thanks
i dont think we going to get any answers this guy is gone.
Can you show me how to fix mine for my electric pride fat tire e bike....got few rips in my wire
Hey does anyone know what those wires are called? My wires got stripped near the axle and i can't buy the wire without the motor..I know its the phase wire but I can't find any online for a brushless motor..
Where can I source the wire?
Where did you get the wire? You can't repair these motors because no one knows where to get the wire?
I'd suggest use a waterproof cable you can buy an extension and cut off what you need
Where can I get one of those clamps?
Where can I buy replacement cable?
Excellent video very well explained,thank you .
Nice video man! 👍🏻 I wonder if Daymak hub motors are this easy!
Great video. Have you ever rewired a geared hub motor? Thanks
Hi. Are you based in the U.S.? Do you have a bike shop? I have the same problem. My hub motor cables are ruined primarily because I have been riding without a torque arm. The rear hub motor twisted sometimes while I was riding and ruined the hub motor wires I had a very hard time finding a torque arm in bike stores
Yeah same it happens to me I only have 2 wires connected now very sketchy but now I’m gonna open it and connected it back
Which brand and model of tire?
hi worked on brother ebikes so many time the cable is the main thing on ebikes that goes bad tip you will need to save up for cells over time s the life of them goes down over time
Thank you. I hope my repair goes as smooth as yours seemed to.
Thanks , just what I needed !
Hi where do you buy the replacement wire and what is the replacement wire called also the connectors to the replacement wire?
It all depends on your motor. In my case, I just cut it down so I didn't but new wire
what wire did you replace that with?
I'm not clear. Replace what?
the replacement Gage wire
I used 12awg wire
I have blow my controller an the bk wheel gone lumpy an will not spin on its own
Im thinking of getting this bike too! Yes anything over 15mph is illegal as you would need MOT, license and insurance. Just get a Dahon p8 and motorize it using the magic pie 3 kits and convert it yourself. That's what im gona do!
BooYaa69 I have the same project as you. Dahon jetstream 8 and magic pie 3 or bafang 8 mid drive! what do you think of bafang mid drive?? its lighter then magic pie thou...
There are so few full suspension folding bikes on the market! But it's necessary for high speeds that electrodrive provides. So Dahon's bike is one of a few to choose from. Good-looking one). Btw, do you remove batteries when fold the bike? If yes, is it fast and easy?
hey, thats cool! did you convert the bike? isnt it ileagal in UK more than 250W?lol