Пікірлер

• 
  @satanicdemon66939 ай бұрын

  How do you empty the oil ?

• 
  @ByCrail Жыл бұрын

  Gas came out of my intake after installing it

• 
  @raymondalvarez9925 Жыл бұрын

  Ordered one of these a couple of weeks ago. Love it. Didn’t need to remove windshield washer reservoir, just relocated it a tad further back

• 
  @tristanboucher5938 Жыл бұрын

  Does it fit on a Mazda 3 2.5l ?

• 
  @timocruze9421 Жыл бұрын

  can i monitor the gages and run the accessport without tuning it? or adding an ots tune

• 
  @DakovP Жыл бұрын

  thanks

• 
  @destinedpure012 жыл бұрын

  Idk if this fits with my aftermarket downpipe that’s what sucks

• 
  @benjamin_photography2 жыл бұрын

  i gave up on the install as soon as you said i need a 10mm socket

• 
  @asheredwards95062 жыл бұрын

  hey so 2:38 do you leave the car dead, or do you press the power button again and turn it off?

• 
  @WraithDeath2 жыл бұрын

  Only downside going FMIC is that absolute cluster mess of loom that's now exposed when you remove the TMIC. Must be a way to de loom all that surely

• 
  @7redstripes2 жыл бұрын

  why did it cause my Intake to start overheating? Smoke was coming out from it smelt burnt

• 
  @RandyAugustus2 жыл бұрын

  All that and no sound clip?

• 
  @richardzarate2822 жыл бұрын

  but its not a motor its an engine man.

• 
  @gnosticone2 жыл бұрын

  Twist and Maneuver the Downpipe out…. But you don’t show us how you did it. Thanks for nothing

• 
  @lalocura18282 жыл бұрын

  Amazing Video

• 
  @adodi_20733 жыл бұрын

  if i’m not gonna do anything to my speed3 gen 2. do i still install a hpfp?

• 
  @derrickheisler57813 жыл бұрын

  How did you compress the housing enough to get the threads started when re installing? Mine is super hard and won’t compress far enough

• 
  @LiLJJ212LP3 жыл бұрын

  Mine is doing the same

• 
  @asurimramirez12497 ай бұрын

  X3, did you guys solved the issue ?

• 
  @derrickheisler57817 ай бұрын

  @@asurimramirez1249 I had to take the whole fuel pump that houses the internals apart to get it to work

• 
  @asurimramirez12497 ай бұрын

  @@derrickheisler5781 :( It would take me more time then, thanks for the tip friend!

• 
  @michaelarroyo84043 жыл бұрын

  the two vaccum hoses: one that goes to cilanoid is attached..furthest from cilanoid... closer one broke apon removing... so inlet doesnt have any hoses going to it ..plugged... is this ok or will i need to repair the houseing that hold oem fitting tips.....thanks

• 
  @singerfpv90443 жыл бұрын

  whats up evan , I know your watching this video lol

• 
  @corie_10323 жыл бұрын

  Is there supposed to be a gas smell after installing? Had mine on for a month and at idle the vents just push in air from the engine bay and it smells and gives me a headache

• 
  @colerobinson36243 жыл бұрын

  if it's catless it will smell.

• 
  @jackrios40403 жыл бұрын

  Thank you for this video. Definitely made it so much easier to replace a bad O2 sensor 🙂

• 
  @LordAdro3 жыл бұрын

  very well done vid

• 
  @bigjohntheboss3 жыл бұрын

  Is this the same Process for generation one 07-09

• 
  @ramiroruizdecastilla30853 жыл бұрын

  Did this mod made your car run rich in fuel? What was the short and long term fuel trim after that?

• 
  @jimmy.t5850 Жыл бұрын

  I would have thought you would need a tune afterwards ? My exact thoughts

• 
  @jimmy.t5850 Жыл бұрын

  Unless the hpfp internals only "allows" for more fuel to pumped through . But the ecu still squirts the same amount of fuel out of the injectors because of the same tune . Possibly answered my own question ??

• 
  @2be3793 жыл бұрын

  this suit fit an speed6 right?

• 
  @crazyfireboy1233 жыл бұрын

  Mine has the ticking idling and barley giving it gas you can hear like a weird noise like I can’t explain it but giving it a lil more throttle it goes away, but I also have a new fuel pump because I stripped my bolt from my old one.. so I don’t know if that’s the reason

• 
  @jimmy.t5850 Жыл бұрын

  My engine ticks at idle . But I know it's the EGR Valve opening and closing constantly

• 
  @stormb3948 Жыл бұрын

  Hey my car is doing the exact same thing with the noise going away at higher rpm. What did the issue end up being?

• 
  @crazyfireboy1233 жыл бұрын

  Hey where can I get a oem fuel pump? I stripped my bolt tryna get my hpfpi in

• 
  @crazyfireboy1233 жыл бұрын

  Where can I get an oem fuel pump??

• 
  @ravenjco3 жыл бұрын

  I would like to know if anyone had tried unscrewing/screwing back the nut w/o a work table. Is it difficult to do with no bench vise?

• 
  @robbutters67343 жыл бұрын

  Yes

• 
  @bluesclue36673 жыл бұрын

  i cant even get the fucking fuse out? they are all stuck in except the small ones. the fuck?

• 
  @jimmy.t5850 Жыл бұрын

  I used a hammer to get mine out

• 
  @mzr35533 жыл бұрын

  Any performance gain fitting this xle valve?

• 
  @creegannn3 жыл бұрын

  I just updated my access port, and cannot change my launch control. Can you help?

• 
  @SrsLe333 жыл бұрын

  Same here it was working before

• 
  @shanemouton76063 жыл бұрын

  about to do this a second time on a second car and here i am watching again... great video man! Thank you so much!!!

• 
  @Dyl_Cam3 жыл бұрын

  Does this work on a 2013 skyactiv? It says its for the speed on the site.

• 
  @jonah91653 жыл бұрын

  I've never used a torque wrench but will be renting one for this job. How do you torque the e8 bolts to spec if you need to continuously switch after every little turn ?

• 
  @kunalpatel42023 жыл бұрын

  you only really need it at the very last turn, when it gets really tight. you can use a normal socket until you start to need a lot of force

• 
  @ulrichmachinerie98274 жыл бұрын

  please can i have parts number of sensor , i m find it

• 
  @topperharlee7184 жыл бұрын

  Very detailed video. You did an awesome job!

• 
  @jozh0074 жыл бұрын

  Thanks for the vídeo

• 
  @michael34084 жыл бұрын

  So I pulled out the Circuit fuse on my 2013 Speed 3 and the car wont die....what could be the reason?

• 
  @GCFIRE3284 жыл бұрын

  I'm having the same issue...

• 
  @michael34084 жыл бұрын

  GCFIRE328 I figured it out, in the video the car shut down right away but in my car it took around 10 minutes of running before it lost fuel. Just leave the car on for awhile then it will shut down

• 
  @OGtrushalpatel4 жыл бұрын

  How could you not show us how it sounds?!

• 
  @jays_rallyspeed34 жыл бұрын

  Excellent video. Thank you! I followed the video literally step by step. I would add one big caution... Recommend using a face shield or be prepared to potentially be sprayed in the face from fuel when disconnecting the full lines. I ran the car out of fuel just like the video shows but had quite alot of residual pressure. Shot a geyser of fuel straight up into my face and had to flush my eyes. Other than that.. everything went great!

• 
  @travisjohnston57782 жыл бұрын

  Should of released fuel cap would of help release some excess pressure

• 
  @jays_rallyspeed32 жыл бұрын

  @@travisjohnston5778 you should share the procedural details to help other's

• 
  @cayzerjin1284 жыл бұрын

  Is the gen 1 Accessport v3 gonna fit on Gen 2?

• 
  @mzr35534 жыл бұрын

  any massive performance increase when installing this?

• 
  @jb65744 жыл бұрын

  You don't have to remove the turbo inlet hose or the battery to do this job

• 
  @rgprgp34544 жыл бұрын

  Dors the mazdaspeed gen 1 and gen 2 use same cobb drop in airfilter

• 
  @richardmondragon4414 жыл бұрын

  Would you rather go for this or a short ram air intake?

• 
  @duey10834 жыл бұрын

  A lot of write-ups mention removing three heat shields. Looks like you only had to remove two? I'm assuming the third heat to remove would be the one on the underside of the exhaust manifold.

• 
  @jb65745 ай бұрын

  Only had to remove two

• 
  @s1d3k1ckRO4 жыл бұрын

  Where do I find the damn bush on the transmission bracket?

• 
  @davidj32884 жыл бұрын

  Does this 3 inch down pipe plug right into my stock exhaust

• 
  @RaulRodriguez-dl8hd4 жыл бұрын

  I'm new to the tunning world , what number should my accesspot should be reading to be sure im not running lean? Thanks guys

• 
  @abdielperez48694 жыл бұрын

  did you ever happen to find out cause i want to eventually tune my car as well.

• 
  @tylerperkins43514 жыл бұрын

  Anything above 10 or -10 is running super lean/rich. At WOT you should be at 0 LTFT. However, most turners like Freektune, and PurpleDrank will work on your LTFT. When I first started my tune, my car was roughly 12 LTFT, but after a few map revisions with Freektune, my car sits at roughly -3, and at WOT it's 0.