Пікірлер

• 
  @aab627Ай бұрын

  the sound 😕

• 
  @user-vj1xd5vz8s9 ай бұрын

  i would like to know, How do you size the piping from the compressor to the equipment and air ports?

• 
  @SorenCicchini11 ай бұрын

  I understand that two air recievers is preferred, but as you said, many organizations only want to pay for one. In this case, should the dryer (assuming they also only will pay for one dryer) be protecting the vessel or downstream of it, protecting the distribution pipework and instruments?

• 
  @coledavidson563011 ай бұрын

  What kind of compressor is good for pressurizing , say, a 2 gallon tank for a small pneumatic cylinder?

• 
  @Victory8Slots Жыл бұрын

  I’ve been watching these videos for the past couple hours. Thank you guys. Hoping to start my own business in a year or two.

• 
  @rizadervisoglu Жыл бұрын

  In our system, we observe pressure fluctuations due to the drying unit (two-stage pressure change style). We use about 6000l/h (max) at 0.62 kPa pressure with a min-max deviation of 0.2kPa. I was planning to install an air tank after the dryer but I was curious about its size and if there is a better solution, maybe a combination of a limiter together with a tank or any other?

• 
  @mercermouth7571 Жыл бұрын

  The information discussed may have been worth hearing so why add a soundtrack on top of low-fidelity audio...?

• 
  @JeremyGaitsch Жыл бұрын

  Nailed it.

• 
  @adolphuszausa9653 Жыл бұрын

  Speed could bee endless

• 
  @adolphuszausa9653 Жыл бұрын

  I would put a small electric motor on the first fan of turbine so when your not using nitros or oxy setaline ethier that's still debatable on which is the better 1 to Use all you do to start it is turn on the air once it's craken at idle air tanks fill instantly so U have instant power on the throttle then I can increase the flow of the first fan of the turbine and fire up some nos to pick up pase the faster it moves the faster the fans turn on there own with out any more spraying or from the electric first fan can switch of so fan free spins

• 
  @adolphuszausa9653 Жыл бұрын

  Put like half dozen spark plugs on the turbine so when you spray oxy setaline or nitrious into turbine and U egnite spark plugs it will flame up and boost like your on a fighter jet but on water

• 
  @adolphuszausa9653 Жыл бұрын

  Then I need to suck hot air from the turbine to air tanks and the air in the tanks will have no moisture

• 
  @adolphuszausa9653 Жыл бұрын

  Hey lying , if I wanted to use air pump to power my jetski ? !!! I would build a fan turbine free spinning blades with compressed air tanks 1 big 1 and couple little tanks , then add a couple oxy setaline tanks small and that's where my boost and after burners come from and a couple small compresors maybe could get some hard core psi coming out of the rear outlet and never need fuel again U can also tap into main turbine to keep air tanks full so free air motor

• 
  @SoftboxLightingKit2 жыл бұрын

  Good sharing. Thank you Sir !

• 
  @BNBFORYOU2 жыл бұрын

  Thank you very much for the wonderful explanation

• 
  @user-zs9dc3cu7d2 жыл бұрын

  Dear Fluid-Aire Dynamics, I have quastion, The distribution piping from Header CDA to POU can install in rain gutter?

• 
  @dancin42 жыл бұрын

  Troubleshooting a system that has failing compressors 4 compressors feeding 8 cigarette machines...3 five HP and one 3 HP....15 cfm on the 5 hp

• 
  @rolandgarcia97422 жыл бұрын

  Thanks 😊

• 
  @commenter54692 жыл бұрын

  VSD thing is not that simple, though! Most of the time when driver is going bad, ( and they do go bad, very often) the price of the replacement offsets the savings, in some cases even surpasses the savings if failed prematurely. Another thing: VFD drivers introduce harmonics to grid, for which power companies penalize end users. Of course there’s line reactors and filters, but that’s another very expensive equipment. I would say better way is to control displacement by mechanical means with something like sliding or plunger valves, or run multiple smaller machines in lead/lag set up fir variable loads - but everybody have jumped on “government stupidity” band wagon, now days!!!

• 
  @rasmysticflame2 жыл бұрын

  I'm here to learn as much as possible!!!

• 
  @adolphuszausa9653 Жыл бұрын

  Could I ask you to read my posts and tell me your thought

• 
  @adolphuszausa9653 Жыл бұрын

  I can me up with that in 7der 10 minutes between typing and designing it in my head as I go

• 
  @adolphuszausa9653 Жыл бұрын

  I think that's free power right besides the nitrous or oxy setaline that would be the only cost

• 
  @adolphuszausa9653 Жыл бұрын

  I say if it was hooked to a generator you would only need to start once

• 
  @jbmoore44362 жыл бұрын

  Is the air required for your system simply the sum of all air needed at each outlet?

• 
  @senthilmsv9222 жыл бұрын

  Very useful

• 
  @ayyappanraj81703 жыл бұрын

  really very usefull your videos

• 
  @seleldjdfmn2214 жыл бұрын

  Thanks for This! whats your favourite song? Enjoy Your day xP

• 
  @mjalals5 жыл бұрын

  Brad: You are exceptionally good in explaining the fact the energy cost is 73% in running the compressors.You impressed upon the viewers that periodically conducting the energy audit is essential in reducing/eliminating the compressed air leakage.A job very well done.Congrats.