Пікірлер

• 
  @Kc8qdq13 күн бұрын

  Do you have to buy the controller when you buy the inverter

• 
  @solarpowerelectricityandel291513 күн бұрын

  yes

• 
  @mrhbwoodrose.265020 күн бұрын

  I have the later model wish i could buy one this size mine is 5 -6ft tall this means i have to unbolt it from my boat to get under bridges

• 
  @solarpowerelectricityandel291520 күн бұрын

  Build a swing joint to fold it!!!

• 
  @roberthorton-hk2rrАй бұрын

  About 7 years ago “GreatNorthWoodsHillbilly” wrote you about using solar air panels to heat air that would be used to dry clothes in a 240v electric dryer adapted to run on 120v. Well I’m there right now. I have the solar panels built and ducted up to a dryer that’s modified to receive the solar-heated air. But I cannot install a 120v power cord into the back of the dryer, the way you demonstrated, without blowing the gfci when I plug it in. Following your lead I retired the red hot lead. Then I jumpered between the empty hot red terminal and the neutral terminal. Finally connected black lead to remaining terminal. Ground went to chassis. The only thing I did that you didn’t mention was disconnecting the heater assembly. All wire ends are taped and safe. Maybe a circuit was broken by the disconnect. What do you think? If I can get this running, then I’ll send you pics and plans. Panels currently produce150F with fan blowing air through collector ducting. I really want this to work. I hope you can help me. Robert Horton

• 
  @solarpowerelectricityandel2915Ай бұрын

  I can help you with this please email me and I will try to help [email protected]

• 
  @BigEightiesNewWaveАй бұрын

  Line-interactive is best trade-off, they call it pure sine wave it is NOT. But way better than junky ones. Online, double conversion are THE BEST.

• 
  @1brasov2 ай бұрын

  So well done!!!!!! Thank you!

• 
  @arlanhenderson64722 ай бұрын

  Thank You! Subscribed! Hope you have a great day!

• 
  @OverUnity77342 ай бұрын

  Didn't I hear, about a year ago, the Federal gov passed a law making animal cruelty a crime in all 50 states? I think your local ASPCA, or even better, your local animal rescue association, could do something with this info.

• 
  @solarpowerelectricityandel29152 ай бұрын

  Tomorrow I make contact them.

• 
  @solarpowerelectricityandel29152 ай бұрын

  10010010111001# passcode

• 
  @fonimer2 ай бұрын

  Why wouldn't you reassemble them BEFORE filling with electrolyte?

• 
  @solarpowerelectricityandel29152 ай бұрын

  cadmium reacts with air, but it’s not super fast at room temp. It forms a thin layer of cadmium oxide on the surface, which actually protects it from more oxidation. If you heat it up, it reacts more. And if there's moisture, it can corrode quicker. Hope that helps!

• 
  @LeslieBryant-bg7zq2 ай бұрын

  11:48

• 
  @LeslieBryant-bg7zq2 ай бұрын

  I h ave a whirlpool dryer now the white wire is hooked up to ground only has 3 wires B, W, R ,is white my nuteral?

• 
  @solarpowerelectricityandel29152 ай бұрын

  it's important to consult a licensed electrician when dealing with electrical issues in your home. It's not recommended to attempt to diagnose or fix electrical problems yourself if you're not qualified to do so.

• 
  @wazza33racer2 ай бұрын

  completely different product from the chinese versions.......which are utter rubbish. With the chinese version, the reactants dissolve into the electrolyte and cause the cell to stop accepting charge because its essentially shorting itself out.

• 
  @solarpowerelectricityandel29152 ай бұрын

  USA batteries are indeed known for their high-quality products compared to some Chinese versions. However, it's important to note that all batteries can have issues regardless of their origin. It might be helpful to consider factors such as the specific model, usage, and maintenance when evaluating battery performance.

• 
  @VarnHomestead2 ай бұрын

  I am careful when dealing with guitar center.

• 
  @solarpowerelectricityandel29152 ай бұрын

  you need to be

• 
  @cockasorrus74753 ай бұрын

  As close to the red green show as I’ve seen. 🤟🏻

• 
  @mykeyehandy-gn2jn3 ай бұрын

  I think. Decreasing the area Heating the plates smashing clothing heating directly on. On the material and vacuum. Can dry your draws in one min. At 500 quarters a drawer. Not a load. But your drawers

• 
  @christopheron49313 ай бұрын

  That has always be earth symbol

• 
  @heathcwalker3 ай бұрын

  I thought black was neutral and white was the positive leg? A different guy jumped leg two to neutral and had black on neutral and white on leg one.

• 
  @solarpowerelectricityandel29153 ай бұрын

  🤣

• 
  @TomGuo10393 ай бұрын

  The Micron gauge function only work with the vacuum sensor？

• 
  @solarpowerelectricityandel29153 ай бұрын

  yes

• 
  @donnellperkins30413 ай бұрын

  Show what you did by doing it on camera. You’re not helping by simply talking about it. People learn from seeing you do the work.

• 
  @rayscruggs79594 ай бұрын

  A few weeks ago in March 2024, my 2018 SR dash display worked, but at 13,000 miles, lost all other 12V Lights, Signals, Horn, and Accessory. Fuses were all good. Took to Zero dealer. dealer hooked up with Zero factory application for remote diagnostics. Zero factory diagnostics said that dash was cutting out (although I never saw display loss or throttle control of the motor). Dealer replaced dash ($200, plus $150 labor) for $350 total. Now all the 12V lights, etc work. I guess the 12V runs through the dash somehow.

• 
  @rayscruggs79594 ай бұрын

  My 2018 SR dash display worked, but at 13,000 miles, lost all other 12V Lights, Signals, Horn, and Accessory. Fuses were all good. Took to Zero dealer. dealer hooked up with Zero factory application for remote diagnostics. Zero factory diagnostics said that dash was cutting out (although I never saw display loss or throttle control of the motor). Dealer replaced dash ($200, plus $150 labor) for $350 total. Now all the 12V lights, etc work. I guess the 12V runs through the dash somehow.

• 
  @losofosokrovakjirka52474 ай бұрын

  Have a nice day . I have the same problem with zero fxs 2016, I don't have a warranty, can you tell me what it is??? thank you very much. It does exactly what it does to me.

• 
  @solarpowerelectricityandel29154 ай бұрын

  12 volt power supply or wiring

• 
  @kellyr90534 ай бұрын

  'Promo sm'

• 
  @parminderdhingra95394 ай бұрын

  How to connect this device to your smart phone?Thanks

• 
  @marioshadjikyriacou33814 ай бұрын

  Is it possible to make an "ac coubling" with a grid tie inverter for off grid use?

• 
  @solarpowerelectricityandel29154 ай бұрын

  You must study the equipment you are using.

• 
  @ruslanruban14815 ай бұрын

  Мог сделать этот обзор с примерами применения

• 
  @cliveramsbotty60775 ай бұрын

  hi philip 20, are you related to 15 peter 20?

• 
  @solarpowerelectricityandel29155 ай бұрын

  No but thanks for asking

• 
  @piggyfan295 ай бұрын

  the compressor is so loud you can hear it all the way around the unit with the even with the door closed

• 
  @solarpowerelectricityandel29155 ай бұрын

  That's just the way the modulation work on the system

• 
  @InertialStasis5 ай бұрын

  Most of the folks here sound like they'd root for the villain... These guitars should have never passed QA. In any country, anywhere.

• 
  @solarpowerelectricityandel29155 ай бұрын

  Good chance, they work for the villain.

• 
  @mts9825 ай бұрын

  cant you adjust the string height? unscrew the tuner and straighten it. Step 1: Unscrew the bridge plate covers (if any) and remove them. Step 2: Make quarter turn adjustments to the saddle height. If the strings are higher, you'll need to push the saddles down, and if the string height is too less, you'll have to bring the saddles up.

• 
  @solarpowerelectricityandel29155 ай бұрын

  Unfortunately, the neck is twisted, so it's a ruin guitar. If I reduce the height, you can't even play 3 notes. Frit 1 D and G-string also fret 7 G string

• 
  @Sinfuldeathband5 ай бұрын

  That’s why I don’t shop at guitar center, along with not having one

• 
  @solarpowerelectricityandel29155 ай бұрын

  I have washed my hands too with guitar center after this Incident

• 
  @thisguy44905 ай бұрын

  yeah there the gamestop of the guitar world.

• 
  @solarpowerelectricityandel29155 ай бұрын

  I can't agree more

• 
  @InertialStasis5 ай бұрын

  Truer words have yet to be spoken.

• 
  @ace95660615 ай бұрын

  I dont like Guitar Center but this is a Jackson QC issue not a GC issue. The crooked tuners are inecusable from jackson, even on a "budget model" but the action being high... it just needs to be setup. Every guitar I own I have had to do a fukll setup on them when i got them. I always go through and install a Tusq nut, polish and level the frets, restring, set the action, neck releif, and intonation. I have to do this on every guitar I own, from my cheap starter Yahmaha (First guitar) to my Gibson Customshop R9 and everything inbetween.

• 
  @solarpowerelectricityandel29155 ай бұрын

  This was a used guitar from guitar center

• 
  @nrich51275 ай бұрын

  Send em back ... they are defective out of the box.

• 
  @solarpowerelectricityandel29155 ай бұрын

  One guitar neck is twisted the other. He can't tune the guitars are useless.

• 
  @InertialStasis5 ай бұрын

  That part

• 
  @solarpowerelectricityandel29155 ай бұрын

  @@InertialStasis Man it's crazy ain't it

• 
  @joshcoughx5 ай бұрын

  Dude, just take it back... wtf.

• 
  @solarpowerelectricityandel29155 ай бұрын

  How did it take you back?

• 
  @jerrymander14925 ай бұрын

  Take Effen thing back! How stupid are you?

• 
  @michaelpreston23925 ай бұрын

  Shouldn’t your jumper wire be going between the two hot wires instead of from a neutral to a hot because now you’re feeding neutral into what used to be a hot wire

• 
  @solarpowerelectricityandel29155 ай бұрын

  If you're not familiar with electricity, you shouldn't work on it. It's incredibly dangerous.

• 
  @bradleyclosson50425 ай бұрын

  It's crazy how some of these import guitars will have a perfect finish and great fretwork yet the pegs will be cock eyed with crooked and screwed strippers. I meant stripped and crooked screws. 😬 Thank God there's no F hole in the way. Gotta love those neon green G strings though.

• 
  @solarpowerelectricityandel29155 ай бұрын

  They must have been hung over when they made this guitar.

• 
  @bradleyclosson50425 ай бұрын

  @@solarpowerelectricityandel2915 🤯

• 
  @ephraimtheendtimessojourner5 ай бұрын

  What you’ve got there is a Friday guitar. It was made on a Friday… 😅

• 
  @solarpowerelectricityandel29155 ай бұрын

  Yeah or a hungover monday

• 
  @InertialStasis5 ай бұрын

  they can be both if friday doesnt stop until monday.... @@solarpowerelectricityandel2915

• 
  @Moby6045 ай бұрын

  You sure it's a real floyd rose?might be a special series 🤣🤣 Never like jackson their too over price their soloist 3 sell for 2400 came up with a floyd 1500 series not the original, basically your telling me you just bought the guitar without checking it🤣🤣🤣🤣🤣🤣

• 
  @solarpowerelectricityandel29155 ай бұрын

  Yo know what I don't know any thing

• 
  @flip4995 ай бұрын

  Ok, this is clearly a factory defect on the misaligned tuner peg. I understand you needed to order it, so its not the actual guitar center that handled the instrument, just write to jackson and they will hook you up with a solution. Or if you dont want to wait for a replacement just fix it yourself, get a drill, make a new hole for the screw to make the angle on the key right. And please, dont order wooden instruments directly to your door, make it ship to the store, have it checked, then leave with it. Otherwise you are going to have to deal with Jackson directly for a replacement

• 
  @solarpowerelectricityandel29155 ай бұрын

  This was not a new guitar was used. Guitar r. I ordered it through guitar centers online service.

• 
  @LucasJRice5 ай бұрын

  It’s not because you wrapped the string around the post like your were spooling a garden hose? That’s too many wraps sir.

• 
  @leviathan_is_me5 ай бұрын

  Wow. I had to go check that again...holy crap.

• 
  @solarpowerelectricityandel29155 ай бұрын

  That is interesting. Guess guitar center put those strings on you guys I didn't

• 
  @solarpowerelectricityandel29155 ай бұрын

  There is many more problems with this guitar that I didn't state in the video.

• 
  @LucasJRice5 ай бұрын

  Did you buy this used? If not it feels like a return and that would make me bloomin angry. Had to return a “great” condition Gibson Les Paul dc because someone tried to glue the whole neck back into the body with super glue, not cool guitar center.

• 
  @solarpowerelectricityandel29155 ай бұрын

  @LucasJRice I did buy both of these used off of the internet

• 
  @6fejmk5 ай бұрын

  adjust it urself lol

• 
  @solarpowerelectricityandel29155 ай бұрын

  The neck on one was twisted it's not fixable

• 
  @Viseo3dp5 ай бұрын

  Jackson basses have always been shit unless you buy there really expensive models and still are not that great.

• 
  @solarpowerelectricityandel29155 ай бұрын

  That is good to know

• 
  @jletsfsu5 ай бұрын

  You usually get what you pay for in the instrument world

• 
  @solarpowerelectricityandel29155 ай бұрын

  I paid for a guitar that works but was sent used turds

• 
  @InertialStasis5 ай бұрын

  You're kind of right however, these two specific guitars should probably never have left the manufacturer. Zero QA done.

• 
  @solarpowerelectricityandel29155 ай бұрын

  It's been an nightmare but i'm getting a refund on both of them

• 
  @snakub4u5 ай бұрын

  I wish he would explain what he is doing in each step.

• 
  @solarpowerelectricityandel29155 ай бұрын

  So the black Mat is fiberglass. Matt, and I'm cleaning the plates off. And you have to keep to plates wet. You can't let them dry and then you replace. The liquid was potassium hydroxide.

• 
  @snakub4u5 ай бұрын

  @@solarpowerelectricityandel2915 So How difficult would it be to replicate those plates for a diy battery?

• 
  @solarpowerelectricityandel29155 ай бұрын

  @@snakub4u i would not do that

• 
  @snakub4u5 ай бұрын

  @@solarpowerelectricityandel2915 Looks simple enough aren't the plates just basically alternating iron and nickel sheet metal.

• 
  @taz36725 ай бұрын

  Didn't you play it and run it through the motions before you bought it and took it home?

• 
  @solarpowerelectricityandel29155 ай бұрын

  They didn't have this in stock, had to order it.

• 
  @taz36725 ай бұрын

  Anything I order, I have shipped to my local GC store and I try it out. I have had some guitars where I told them I did not want.@@solarpowerelectricityandel2915

• 
  @Sequisha5 ай бұрын

  I'm fairly certain Guitar Centers and all the big chains buy botched and lemon guitars at a discount and mark up the price; I will NEVER buy another one from a big chain dealers. Literally asking for a twisted neck or some major quality issue.

• 
  @solarpowerelectricityandel29155 ай бұрын

  I get it man

• 
  @matthewearl98245 ай бұрын

  ALL instruments you buy whether $150 or $5000 bucks needs to be set up properly when you get them. It is common knowledge that instruments will be mostly unplayable or have slight issues until this is done. Also the crooked tuner is a Jackson issue not GC. I own over 7 Jacksons and none of them are under $1500 in price and don't usually have these QC issues.

• 
  @solarpowerelectricityandel29155 ай бұрын

  The neck on one was twisted. There's no fixing it.

• 
  @riverrail5 ай бұрын

  I bought a Jackson Bass for my son for Christmas three years ago from Amazon. I pulled out of the box to see if everything is alright. Had the same thing with the G tuner. Crooked and would interfere with the D tuner. set it back and got another one and was perfect. It's a Jackson issue.

• 
  @solarpowerelectricityandel29155 ай бұрын

  It's the new manufacturers not the ones