I thought 30 weight non detergent was better i was told by father inlaw
@mariancrist3 ай бұрын
"Promo sm"
@cody4813 ай бұрын
You have an extremely expensive machine that needs very little work to return to its former glory. Your videos are excellent. Please make more.
@cody4813 ай бұрын
The front plate and mounting pieces stay on the tractor unless you have to remove them for a 3 point or sleeve hitch or front mounted items.
@cody4813 ай бұрын
The front plate and mounting pieces stay on the tractor unless you have to remove them for a 3 point or sleeve hitch or front mounted items.
@cody4813 ай бұрын
The case has a "drive over deck " just back up over it. You might find 2 short 2x4s useful under the tires.
@cody4813 ай бұрын
Not hydrostatic, its a different type of pump. They drive very differently.
@Bigfoot_fixes_all4 ай бұрын
Just gotta pull the brake back might be a little stiff from sitting
@scottfoster24874 ай бұрын
Front handle has been teaked,sittin to far back on the recoil side. A saw scrench fits the fuel and oil caps on these saws. Replace the fuel and impulse lines and spark plug. Good little trim saws for sure.
@billbyrnes95054 ай бұрын
Only one tire was mounted backwards. But, from the looks of things, new back tires would be in order?
@billbyrnes95054 ай бұрын
Steiner, out of Illinois, has most anything you would want. They can tell you what year it is by the serial number. I bought one, 1952, thought it was a 54 for twenty years, went to buy something for it and that told me it was a 52. Thirty plus years later, all I did was update to a twelve volt system, repaired the radiator, out a new fancy, comfortable seat on it, and after twenty five years, give or take a couple, new clutch. The people I bought it from, their dad was redoing it. I have no idea what he had done to it, but oil changes and tune ups is about it. And one muffler. Funny story, after ten, or fifteen years, the thing started act ing up, not idling right, could not figure it out. Went back to basics, started with timing, 180 out. Lets go back to the beginning, the tractor would never idle less than about a thousand RPM's. Always had to throttle up. Now, back to the future, we found out it the distributor was 180 out. Fixed that, checked the plugs, reset the points, and, BOOM. The dang thing would idle at 60 RPM, which is way too low but would idle, anywhere I wanted it to? Go figure. Exhaust pointing down, like any exhaust, looks cool, UNTIL, you get in the dirt. No muffler, sparks may fly in dry grass, hay field, grass fire? So, now as we speak, I have a wheel seal leaking, along with my twenty year old radiator fix is leaking again. If you ever have to split your tractor, mark your throttle, governor, and anything else that may need to be put back in the same spot. Enjoy the tractor, I am still enjoying mine. Oh yea, a solid mount tow bar was added, better than the bar that goes on the hydraulic arms. Located in NE Ohio.
@Mclean_mcnamara4 ай бұрын
That’s awesome. These tractors are beasts. They don’t make them like they used too
@i58985 ай бұрын
Me paso desde hay aprendí a no desmontar la cadena sin quitar el freno
@user-lo6cf3df1x6 ай бұрын
Stay with the kid you're doing a good job
@Toby-ep7pn6 ай бұрын
It is the chain break dummy
@thomasmcquade50977 ай бұрын
Why didn’t you change the oil filter
@Mclean_mcnamara7 ай бұрын
I did I just forgot when I was filming
@barrychambers40478 ай бұрын
It ain't fixed until you get that pine tree down!
@Mclean_mcnamara8 ай бұрын
I’m embarrassed to admit how long I left it for but it was out away from anything it could hurt and it’s down and dealt with now
@barrychambers40478 ай бұрын
That's how I always unlock my brake!🤣
@richsepe4118 ай бұрын
Do it for me today or this weekend in the cold weather .
@richsepe4118 ай бұрын
Can you please do a cold start of your backpack leafblower the hard starting weedwacker and chainsaw for me today McLean.This is a special request video.Inculde all your satisfying pulls as well I love when you pull them !
@richsepe4118 ай бұрын
Today.
@richsepe4118 ай бұрын
Can you please cold start the backpack leafblower weedwacker,chainsaw mantis tiller for me today McLean in the cold.Inculde more satisfying pulls ,nice underwear I’m the last video ! Say common start to when you pull the weedwacker and chainsaw .This is a special request video.
@gudfarfar8 ай бұрын
When nuts are sticking too bad, use heat on them. Get a blowtorch or an induction heater and heat them up. The corrosion holding them will give and you will be able to get them off. Just beware of the hot surface, and use gloves.
@richsepe4118 ай бұрын
Can you please do a cold start of the backpack leaf blowers,weedwackers and chainsaws for me today Inculde all the pulls as well just like the last video and make it satisfying for me!This is a special request video.
@Mclean_mcnamara8 ай бұрын
Yeah I can try to get a video out of all that soon
@richsepe4118 ай бұрын
@@Mclean_mcnamara can you please do a cold start of your backpack leafblower hard starting weedwacker and chainsaw for me today McLean,this is a special request video Inculde all of your satisfying pulls for me to!
@Mclean_mcnamara8 ай бұрын
@@richsepe411 can’t today but I’ll get to it soon as I can
@richsepe4118 ай бұрын
Can you do more satisfying pulls on the weedwacker ,leaflowers
@TF8569 ай бұрын
By the way, I love your tractor.
@Mclean_mcnamara9 ай бұрын
Means a lot!
@TF8569 ай бұрын
Stop trying to break the fittings off. You are supposed to move it off center and pull it off. Don't keep pushing it sideways till it breaks off. I have greased a lot of tractors and never saw one break off. Get a different nozzle for the grease gun that has a level release Called A LockNLube grease gun coupler! But there are other cheaper brands around $10.00. And absolutely get a flexible hose! Never use a solid metal tube.
@douglasjackson70209 ай бұрын
Dude, looking at the smoke billowing out the shredder hopper and the strain to chip those branches, I'd say your chipper blades need to be sharpened!
@adriaenswirt74729 ай бұрын
*promo sm*
@rahmliggett10 ай бұрын
dammit boy they don't make them tillers like they used to
@Mclean_mcnamara10 ай бұрын
Amen to that rahmabawl
@stevem3173 Жыл бұрын
Well that was satisfying, those first dozen pulls had me worried! Now you need to set aside some space so we can put in a forge area! Let's build a lean-to!
@Mclean_mcnamara Жыл бұрын
That would be sweet
@danbentsen Жыл бұрын
Looks like you have a bent PTO Shaft, w/erratic spin
@Mclean_mcnamara Жыл бұрын
It’s definitely not as straight as it should be but the pto has an adapter on it that is very loose and makes the spin look much worse than it really is. I need to just take it off because there is no way it’s safe to use as is haha
@farmtofishing9994 Жыл бұрын
Did you just sell this tractor on Facebook market places
@Mclean_mcnamara Жыл бұрын
Not yet but trying too
@stevem3173 Жыл бұрын
Susan is all about that pineapple life!
@Mclean_mcnamara Жыл бұрын
She’s nonstop
@jeffmurdock2713 Жыл бұрын
You could have drove over it. That might work
@robertbeechy6475 Жыл бұрын
You pull straight out on your gun you have a small screen in the tank unscrew the fitting and clean the screen
@stevem3173 Жыл бұрын
Looks like Susan was waiting for you to fall off that ramp!
@Mclean_mcnamara Жыл бұрын
Probably hoping for me to fall so I can get down and throw her pineapple sooner
@dakota7012 Жыл бұрын
You cut down that whole damn tree with the brake on it looks like 😂 but hey you can’t beat a $50 saw of that brand. I found three for 100 online that I’m interested in buying to make run again
@thomasfrost69936 ай бұрын
To me it sounded like a dry chain, either he forgot to put bar oil in or the pump wasn't working.
@flhusa1 Жыл бұрын
Swap your rear wheels side to side. Tread facing wrong way
@flhusa1 Жыл бұрын
C-clamp at bend and turn pipe 90 Degrees in your vise.
@flhusa1 Жыл бұрын
Oil pours out the container better if you pour with neck at top. Should be a diagram at top. Same for ant I freeze jug.
@Miniscapes515 Жыл бұрын
I found it safer to use a ratchet strap tight around the tire while you pump with air to rest the bead. It works for me evwrytime. All size if tires.
@TF8569 ай бұрын
I have seen some that wrap around the tire and were inflated with air to squeeze the tire.
@buffsheeri Жыл бұрын
drove one of those for years on my uncle's farm.
@adrianstefan23 Жыл бұрын
new subscriber👍👍
@Mclean_mcnamara Жыл бұрын
Means the world 🙏
@NathanBlosser Жыл бұрын
You shouldn't cut down trees the way you did that small pine, notch should be about 1/3 depth of the diameter, and backcut should be even to just slightly above the bottom kerf of your notch and flat, not angled. If you use a humboldt notch then it would even with the top kerf. When bucking up the log cut only about 2/3 of the way through the log and roll it over to finish the cut, even half a second into the dirt will take the edge off the chain. If you can't roll it over cut the remaining bottom part with the bottom tip of the bar watching carefully to keep it out of the dirt. Also one last thing if you are trying to clear out a flooded carb, place the bar on a log, holding the trigger of the chainsaw wide open and pull several times, this will force more air through the venturi and clean out the excess gas.
@Mclean_mcnamara Жыл бұрын
Thanks for the tips, I’ll remember for next time!
@scottlowther7698 Жыл бұрын
Least that's what Buckin Billy Ray says. 😂
@mr.homelite8490 Жыл бұрын
Sounds like it's missing, maybe new plugs,wires & points.
@scottfoster2487 Жыл бұрын
Do not sharpen a chain the way your doing it ,you basicly are dulling the chain and file. File from inside to out is the best method,you want a really sharp chain get a two in one file ,it doeas rakers and tooth in on swipe. Replace the bar and see if that heklps keep the chain on . To properly tension a chain,lift the nose of the bar as your tensioning the chain.
@Mclean_mcnamara Жыл бұрын
Will do thanks
@richardhaughey532 Жыл бұрын
Spray foam does not hold up a tube would be better
@Mclean_mcnamara Жыл бұрын
I concur that it does not hold up indeed haha
@urbanitesgarage32999 ай бұрын
@@Mclean_mcnamaralol yep I learned the hard way even on a tiny little mower tire it lasted like 5 minutes
@malvernmascall-yc6sz Жыл бұрын
I wish you good luck in the future young man I wish I could fix my lawn mower and chains saw and weed whacker I live in Antigua and Barbuda good work
Пікірлер
I thought 30 weight non detergent was better i was told by father inlaw
"Promo sm"
You have an extremely expensive machine that needs very little work to return to its former glory. Your videos are excellent. Please make more.
The front plate and mounting pieces stay on the tractor unless you have to remove them for a 3 point or sleeve hitch or front mounted items.
The front plate and mounting pieces stay on the tractor unless you have to remove them for a 3 point or sleeve hitch or front mounted items.
The case has a "drive over deck " just back up over it. You might find 2 short 2x4s useful under the tires.
Not hydrostatic, its a different type of pump. They drive very differently.
Just gotta pull the brake back might be a little stiff from sitting
Front handle has been teaked,sittin to far back on the recoil side. A saw scrench fits the fuel and oil caps on these saws. Replace the fuel and impulse lines and spark plug. Good little trim saws for sure.
Only one tire was mounted backwards. But, from the looks of things, new back tires would be in order?
Steiner, out of Illinois, has most anything you would want. They can tell you what year it is by the serial number. I bought one, 1952, thought it was a 54 for twenty years, went to buy something for it and that told me it was a 52. Thirty plus years later, all I did was update to a twelve volt system, repaired the radiator, out a new fancy, comfortable seat on it, and after twenty five years, give or take a couple, new clutch. The people I bought it from, their dad was redoing it. I have no idea what he had done to it, but oil changes and tune ups is about it. And one muffler. Funny story, after ten, or fifteen years, the thing started act ing up, not idling right, could not figure it out. Went back to basics, started with timing, 180 out. Lets go back to the beginning, the tractor would never idle less than about a thousand RPM's. Always had to throttle up. Now, back to the future, we found out it the distributor was 180 out. Fixed that, checked the plugs, reset the points, and, BOOM. The dang thing would idle at 60 RPM, which is way too low but would idle, anywhere I wanted it to? Go figure. Exhaust pointing down, like any exhaust, looks cool, UNTIL, you get in the dirt. No muffler, sparks may fly in dry grass, hay field, grass fire? So, now as we speak, I have a wheel seal leaking, along with my twenty year old radiator fix is leaking again. If you ever have to split your tractor, mark your throttle, governor, and anything else that may need to be put back in the same spot. Enjoy the tractor, I am still enjoying mine. Oh yea, a solid mount tow bar was added, better than the bar that goes on the hydraulic arms. Located in NE Ohio.
That’s awesome. These tractors are beasts. They don’t make them like they used too
Me paso desde hay aprendí a no desmontar la cadena sin quitar el freno
Stay with the kid you're doing a good job
It is the chain break dummy
Why didn’t you change the oil filter
I did I just forgot when I was filming
It ain't fixed until you get that pine tree down!
I’m embarrassed to admit how long I left it for but it was out away from anything it could hurt and it’s down and dealt with now
That's how I always unlock my brake!🤣
Do it for me today or this weekend in the cold weather .
Can you please do a cold start of your backpack leafblower the hard starting weedwacker and chainsaw for me today McLean.This is a special request video.Inculde all your satisfying pulls as well I love when you pull them !
Today.
Can you please cold start the backpack leafblower weedwacker,chainsaw mantis tiller for me today McLean in the cold.Inculde more satisfying pulls ,nice underwear I’m the last video ! Say common start to when you pull the weedwacker and chainsaw .This is a special request video.
When nuts are sticking too bad, use heat on them. Get a blowtorch or an induction heater and heat them up. The corrosion holding them will give and you will be able to get them off. Just beware of the hot surface, and use gloves.
Can you please do a cold start of the backpack leaf blowers,weedwackers and chainsaws for me today Inculde all the pulls as well just like the last video and make it satisfying for me!This is a special request video.
Yeah I can try to get a video out of all that soon
@@Mclean_mcnamara can you please do a cold start of your backpack leafblower hard starting weedwacker and chainsaw for me today McLean,this is a special request video Inculde all of your satisfying pulls for me to!
@@richsepe411 can’t today but I’ll get to it soon as I can
Can you do more satisfying pulls on the weedwacker ,leaflowers
By the way, I love your tractor.
Means a lot!
Stop trying to break the fittings off. You are supposed to move it off center and pull it off. Don't keep pushing it sideways till it breaks off. I have greased a lot of tractors and never saw one break off. Get a different nozzle for the grease gun that has a level release Called A LockNLube grease gun coupler! But there are other cheaper brands around $10.00. And absolutely get a flexible hose! Never use a solid metal tube.
Dude, looking at the smoke billowing out the shredder hopper and the strain to chip those branches, I'd say your chipper blades need to be sharpened!
*promo sm*
dammit boy they don't make them tillers like they used to
Amen to that rahmabawl
Well that was satisfying, those first dozen pulls had me worried! Now you need to set aside some space so we can put in a forge area! Let's build a lean-to!
That would be sweet
Looks like you have a bent PTO Shaft, w/erratic spin
It’s definitely not as straight as it should be but the pto has an adapter on it that is very loose and makes the spin look much worse than it really is. I need to just take it off because there is no way it’s safe to use as is haha
Did you just sell this tractor on Facebook market places
Not yet but trying too
Susan is all about that pineapple life!
She’s nonstop
You could have drove over it. That might work
You pull straight out on your gun you have a small screen in the tank unscrew the fitting and clean the screen
Looks like Susan was waiting for you to fall off that ramp!
Probably hoping for me to fall so I can get down and throw her pineapple sooner
You cut down that whole damn tree with the brake on it looks like 😂 but hey you can’t beat a $50 saw of that brand. I found three for 100 online that I’m interested in buying to make run again
To me it sounded like a dry chain, either he forgot to put bar oil in or the pump wasn't working.
Swap your rear wheels side to side. Tread facing wrong way
C-clamp at bend and turn pipe 90 Degrees in your vise.
Oil pours out the container better if you pour with neck at top. Should be a diagram at top. Same for ant I freeze jug.
I found it safer to use a ratchet strap tight around the tire while you pump with air to rest the bead. It works for me evwrytime. All size if tires.
I have seen some that wrap around the tire and were inflated with air to squeeze the tire.
drove one of those for years on my uncle's farm.
new subscriber👍👍
Means the world 🙏
You shouldn't cut down trees the way you did that small pine, notch should be about 1/3 depth of the diameter, and backcut should be even to just slightly above the bottom kerf of your notch and flat, not angled. If you use a humboldt notch then it would even with the top kerf. When bucking up the log cut only about 2/3 of the way through the log and roll it over to finish the cut, even half a second into the dirt will take the edge off the chain. If you can't roll it over cut the remaining bottom part with the bottom tip of the bar watching carefully to keep it out of the dirt. Also one last thing if you are trying to clear out a flooded carb, place the bar on a log, holding the trigger of the chainsaw wide open and pull several times, this will force more air through the venturi and clean out the excess gas.
Thanks for the tips, I’ll remember for next time!
Least that's what Buckin Billy Ray says. 😂
Sounds like it's missing, maybe new plugs,wires & points.
Do not sharpen a chain the way your doing it ,you basicly are dulling the chain and file. File from inside to out is the best method,you want a really sharp chain get a two in one file ,it doeas rakers and tooth in on swipe. Replace the bar and see if that heklps keep the chain on . To properly tension a chain,lift the nose of the bar as your tensioning the chain.
Will do thanks
Spray foam does not hold up a tube would be better
I concur that it does not hold up indeed haha
@@Mclean_mcnamaralol yep I learned the hard way even on a tiny little mower tire it lasted like 5 minutes
I wish you good luck in the future young man I wish I could fix my lawn mower and chains saw and weed whacker I live in Antigua and Barbuda good work
Yesssirr!!! Lookin good!
kzread.info/dash/bejne/aH1ny5Wmcs6WpqQ.html