I have the same problem Basically CHINA has screwed us all.
@arieldearmas5913 Жыл бұрын
Saludos. Me ha parecido interesante su video pués mi TC-2 presenta la misma falla. Ha podido reparar la falla?
@MrJuvepentium9 ай бұрын
en mi caso el chip principal se fue a corto, compre otro equipo misma generacion (yellow) igual se daño, y compre un tercero el azul,
@didierrfabianmathewsgomez2886 Жыл бұрын
Me too, the same problem, fnirsi told me the problem was in the mm32 and ch32, i bought it from fnirsi (U$ 8) too, to fix the problem, so I replaced them, it works sometimes, sometimes does not, must be reset several times to make it work, i think there is a regulator or oscillator broken, not the mm32/ch32, so i still looking for the issue.
@BB-vq2zv Жыл бұрын
A gomolya sajtnak nincs párja. csak tippelek szerintem a felvétel Erdelyben készült.
@risingsunflagsamemeaningas7472 Жыл бұрын
I am using DSO-TC2 all buttons other than the power button did not work. Regarding button input... from M32F103 microprocessor chip..... If the key is pressed at 5V, it changes to 0V It is estimated that there is no change in the screen It is expected that there will be an internal problem of M32F103. pin no / button not pressing voltage / button pressinf action vaoltage 34 power / 5v /0v 35 ok (left) / 5v /0v 36 menu / 5v /0v 39 up / 5v /0v 40 down / 5v /0v 42 test(right) / 5v /0v
@MrJuvepentium Жыл бұрын
El mismo problema, no enciende, Cambie el V05 y no funcionó, revisión completa de todo el equipo, lo abrí y un LED rojo prende al pisar ON, cuando dejas de presionar ON el LED interno se apaga Off, al tratar de prender solo logro ver el LED interno en rojo y conseguí medir en el MM32F104 los pines 18 VSS y PIN 19 VCC estaba en corto el VSS con el VCC TENIA UN VALOR DE 1 OHMIO
@user-ky7gq8xg3g9 ай бұрын
After the palace, did the device work?
@MrJuvepentium9 ай бұрын
@@user-ky7gq8xg3g In my case the main chip went short, I bought another device yellow and it was damaged, and I bought a third one, the blue one.
@user-pn5um6nk1b Жыл бұрын
Перестал включаться после месяца использования. Включается, выключается, завис на выборе режимов тестера и осциллографа. На остальные кнопки не реагируют. официалы (фнирси) не знают решение такой проблемы. Так вот может кому будет полезно если включить прибор и удерживать кнопку вниз то прибор включиться и внизу будет надпись mm boot, какое то загрузочное меню и в нем кнопки все работают, так как слышно звуковое подтверждение. Проблему с запуском это не решает, пишу просто может кому пригодится, лайкните что заменили.
@AmudeshP Жыл бұрын
I have the same problem any one can help me?
@semorgh28548 ай бұрын
If you can sell the battery and Display. it is a peace of junk.
@muratmert7990 Жыл бұрын
I have the same problem but i got a refund. 👏👏👏 AliExpress I have the device😊
@Cyster123 Жыл бұрын
I have the same problem!!!
@bikerikintolz Жыл бұрын
i have to the same problem what to do??
@Cyster123 Жыл бұрын
I've contacted the company that makes these oscilloscopes. They didn't seem to know what the issue was.
@jorgespina5513 Жыл бұрын
I´ve the same problem. if anyone has the solution please share it
@Kris0725PL Жыл бұрын
Did you try reset device with button inside?
@risingsunflagsamemeaningas7472 Жыл бұрын
@@Kris0725PL i have tried but it doesn't work
@Kris0725PL Жыл бұрын
@@risingsunflagsamemeaningas7472 hardware fail..
@MrJuvepentium9 ай бұрын
In my case the main chip went short, I bought another device and it was damaged, and I bought a third one, the blue one.
@luizrobertomartins-myperso9723 Жыл бұрын
I have the same problem. I opened the package today. This is new. I was testing an electronic gate capacitor. The capacitor charged a little during the test. When I moved the capacitor around to test in another slot, I saw a small spark. Later I pressed the power button and it just flashed the screen and didn't turn on anymore.
@MuhammedAli-by9lx Жыл бұрын
did you figure. out what part it burned inside?
@Kris0725PL Жыл бұрын
@@MuhammedAli-by9lx in my fault ARM big...array diode , 86262i and s8vi. On my channel i have video about this device. Broken with capacitor not discharge ;)
@ainsworthlynch11 ай бұрын
The manual warns not to test capacitor with any charge in it.
@stephenklu3689 Жыл бұрын
I have the same problem how do you fix it?
@laszlokratochwill9962 Жыл бұрын
I don't know the solution, fortunately I was within 15 days. The seller will send a new one. How long did it take for it to go bad?
@stephenklu3689 Жыл бұрын
@@laszlokratochwill9962 the same day I got it and I test a capacitor and it went off on its own I thought the battery went low. After fully charging it never turn on. The screen flick in a split second and off
@VoeViking Жыл бұрын
@@stephenklu3689 Capacitors will kill this with ease. Will try to find a way to fix it.
@MuhammedAli-by9lx Жыл бұрын
@@VoeViking do you know what it hits first on board?
@Kris0725PL Жыл бұрын
@@MuhammedAli-by9lx array diode....protection. if fails ARM !)
Пікірлер
Köszi .
Ez az élet
I have the same problem Basically CHINA has screwed us all.
Saludos. Me ha parecido interesante su video pués mi TC-2 presenta la misma falla. Ha podido reparar la falla?
en mi caso el chip principal se fue a corto, compre otro equipo misma generacion (yellow) igual se daño, y compre un tercero el azul,
Me too, the same problem, fnirsi told me the problem was in the mm32 and ch32, i bought it from fnirsi (U$ 8) too, to fix the problem, so I replaced them, it works sometimes, sometimes does not, must be reset several times to make it work, i think there is a regulator or oscillator broken, not the mm32/ch32, so i still looking for the issue.
A gomolya sajtnak nincs párja. csak tippelek szerintem a felvétel Erdelyben készült.
I am using DSO-TC2 all buttons other than the power button did not work. Regarding button input... from M32F103 microprocessor chip..... If the key is pressed at 5V, it changes to 0V It is estimated that there is no change in the screen It is expected that there will be an internal problem of M32F103. pin no / button not pressing voltage / button pressinf action vaoltage 34 power / 5v /0v 35 ok (left) / 5v /0v 36 menu / 5v /0v 39 up / 5v /0v 40 down / 5v /0v 42 test(right) / 5v /0v
El mismo problema, no enciende, Cambie el V05 y no funcionó, revisión completa de todo el equipo, lo abrí y un LED rojo prende al pisar ON, cuando dejas de presionar ON el LED interno se apaga Off, al tratar de prender solo logro ver el LED interno en rojo y conseguí medir en el MM32F104 los pines 18 VSS y PIN 19 VCC estaba en corto el VSS con el VCC TENIA UN VALOR DE 1 OHMIO
After the palace, did the device work?
@@user-ky7gq8xg3g In my case the main chip went short, I bought another device yellow and it was damaged, and I bought a third one, the blue one.
Перестал включаться после месяца использования. Включается, выключается, завис на выборе режимов тестера и осциллографа. На остальные кнопки не реагируют. официалы (фнирси) не знают решение такой проблемы. Так вот может кому будет полезно если включить прибор и удерживать кнопку вниз то прибор включиться и внизу будет надпись mm boot, какое то загрузочное меню и в нем кнопки все работают, так как слышно звуковое подтверждение. Проблему с запуском это не решает, пишу просто может кому пригодится, лайкните что заменили.
I have the same problem any one can help me?
If you can sell the battery and Display. it is a peace of junk.
I have the same problem but i got a refund. 👏👏👏 AliExpress I have the device😊
I have the same problem!!!
i have to the same problem what to do??
I've contacted the company that makes these oscilloscopes. They didn't seem to know what the issue was.
I´ve the same problem. if anyone has the solution please share it
Did you try reset device with button inside?
@@Kris0725PL i have tried but it doesn't work
@@risingsunflagsamemeaningas7472 hardware fail..
In my case the main chip went short, I bought another device and it was damaged, and I bought a third one, the blue one.
I have the same problem. I opened the package today. This is new. I was testing an electronic gate capacitor. The capacitor charged a little during the test. When I moved the capacitor around to test in another slot, I saw a small spark. Later I pressed the power button and it just flashed the screen and didn't turn on anymore.
did you figure. out what part it burned inside?
@@MuhammedAli-by9lx in my fault ARM big...array diode , 86262i and s8vi. On my channel i have video about this device. Broken with capacitor not discharge ;)
The manual warns not to test capacitor with any charge in it.
I have the same problem how do you fix it?
I don't know the solution, fortunately I was within 15 days. The seller will send a new one. How long did it take for it to go bad?
@@laszlokratochwill9962 the same day I got it and I test a capacitor and it went off on its own I thought the battery went low. After fully charging it never turn on. The screen flick in a split second and off
@@stephenklu3689 Capacitors will kill this with ease. Will try to find a way to fix it.
@@VoeViking do you know what it hits first on board?
@@MuhammedAli-by9lx array diode....protection. if fails ARM !)
Igual mio se malogro solo
Mukemmel