Пікірлер

• 
  @k6ul2 ай бұрын

  Good video. I’ve done a lot of these over the years. I like your process. I’ve never tried the assembly lube. I agree the grease I’ve tried does tend to dry out (and pick up debris).

• 
  @7-oaksfarm2 ай бұрын

  Thanks, I can't say that is a original idea a equipment dealer told me that was what one of the manufactures was recommending now. So far have had some done for over five years and haven't had to address them yet still working good.

• 
  @mikej8126 ай бұрын

  Have you needed to replace a bearing ?

• 
  @7-oaksfarm6 ай бұрын

  I have never needed to replace a bearing but I did have two that came loose on the swaged in rivet and would spin on the rivet instead of the bearing. I put rivet in press with a punch and flared it a little, then tack welded to the rail and kept it from spinning been working for a couple years like that.

• 
  @k6ul2 ай бұрын

  I’ve got a couple bad bearings. I couldn’t find replacements through Stanley (didn’t exhaust all possibilities). Bearing looks standard was going to just try and find form/fit/function equivalent. Drill out old rivet and replace with a new rivet (gotta find that too).

• 
  @stickermigtigger9 ай бұрын

  I just use my auto floor jack. 🙂

• 
  @7-oaksfarm9 ай бұрын

  That's actually not a bad idea, may see about using one of my rollers on top of jack! Thanks!

• 
  @stickermigtigger9 ай бұрын

  @@7-oaksfarm Works great for really heavy stuff. Too cumbersome for small stuff. Using the floor jack you can do a lot of position changes like alignment by hand or using the saw clamp to force it; tighten the clamp and the jack will roll left or right. What would REALLY be cool would be a Wi-Fi enabled floor jack. 😂😂

• 
  @7-oaksfarm9 ай бұрын

  @@stickermigtigger You got that right a powered floor jack like a plane tug would be slick lol... Will have to ponder on your idea and see what I come up with....

• 
  @homemadetools9 ай бұрын

  Enable embedding on external websites please. We'd like to post this on our homemade tool forum.

• 
  @7-oaksfarm9 ай бұрын

  I'm new to this, I think I got it changed over. Thanks for sharing I will check you guys out as well!!!

• 
  @Ron-FabandBuild9 ай бұрын

  Good job sir, I have more than four in my shop. I find my self using long lengths of material. Thank you for the video

• 
  @7-oaksfarm9 ай бұрын

  Thanks!!! Going to build one more for sure will see after that.

• 
  @Justalittleoutoftown9 ай бұрын

  Looks like it’s going to work good. Nice collection of tools.

• 
  @7-oaksfarm9 ай бұрын

  Thanks that's been my vice in life, pretty much all where bought used though enjoy going to estate sales...

• 
  @dannywilsher41659 ай бұрын

  I used to build jack stands with a 1" all thread in a pipe with two rods welded to the nut on the all thread. This made jacking and leveling simple and easy.

• 
  @7-oaksfarm9 ай бұрын

  @@dannywilsher4165 I seriously considered doing that but was worried about having to hold both sides to keep from rotating while raising lowering vs just cranking a handle, definitely a easy solution though. Thanks for the suggestion!

• 
  @dannywilsher41659 ай бұрын

  My pleasure!@@7-oaksfarm

• 
  @Justalittleoutoftown9 ай бұрын

  That’s a lot of mud to move. At least you have a bigger machine than I used. Hope I don’t ever have to dredge mine.

• 
  @7-oaksfarm9 ай бұрын

  Thanks, I quit counting at dump truck three hundred and something. I'm currently only halfway done hope to throw at least a quarter of it over dam to improve back slope. Hope it speeds up not trucking it then but I've been proved wrong a lot so far. I hope I never have to see this pond dry again as well...

• 
  @jenniferwhite608911 ай бұрын

  i have a working farm shop i have mechanics working for me the pave their personal tools cabinets and i do have for each one a full set of Mac ot snap-on tools them i supply specialized tools too Someone said i had over 200 boxes of tools in different shops to and all are full with tools too talking a long time to design a shop that would work for me too 5 years of planning it not profited at all size of it has out gwon it now

• 
  @7-oaksfarm11 ай бұрын

  Sounds nice and way fancier than what I have, we are just a small family farm. Thanks for watching!

• 
  @joshtonry429111 ай бұрын

  How this is that top? Looks like 2-3" thick

• 
  @7-oaksfarm11 ай бұрын

  The top is 2.5" thick and 6ft x 8ft. It was a old plastic mold injection press backing plate.

• 
  @joshtonry429111 ай бұрын

  Thats wild

• 
  @avinaashashastry391011 ай бұрын

  Very light music.

• 
  @7-oaksfarm11 ай бұрын

  Thanks for the suggestion just my fifth video I've ever made very much still learning.

• 
  @avinaashashastry391011 ай бұрын

  Some music.

• 
  @7-oaksfarm11 ай бұрын

  thanks for the suggestion!

• 
  @davidgroff3355 Жыл бұрын

  How large pond? Is it spreed or drainage

• 
  @7-oaksfarm Жыл бұрын

  I haven't calculated it out but would estimate 1/4 acre not very big. Mainly needed dam to act as a road to access back of property, this is a swampy drain that runs into it.

• 
  @po4RP20361 Жыл бұрын

  Nice job. Hope to see other projects so I subscribed

• 
  @7-oaksfarm Жыл бұрын

  Thanks first video I ever made, working on larger pond on property now hope to have some videos out soon on it....

• 
  @po4RP20361 Жыл бұрын

  @@7-oaksfarm Lookin forward to it, stay safe and have fun

• 
  @jyienger Жыл бұрын

  Nice build. Great job. How did you get water so fast?

• 
  @7-oaksfarm Жыл бұрын

  Thanks was our very first one so a lot of lessons where definitely learned. The reason for us buying the excavator was to dredge the 3 acre pond which is upstream of this one. So we drained water out of large pond, which we are currently working on. Going to do a few videos on it as well but having some computer issues...