Пікірлер

• 
  @wongyeeyong2214Күн бұрын

  Would be great if you could teardown the 7.2V battery pack and review the batteries and the BMS PCB inside.

• 
  @Wishwellpomeyie2 күн бұрын

  Did I hear 66 screws for the keyboard?

• 
  @chunion7453 күн бұрын

  any opinion on the sidebrush with more than three brushes? In your experience does it make any difference?

• 
  @owaisnajam53046 күн бұрын

  Nice tutorial video. I have Hameg 1004-3 oscilloscope and by mistake I shorted DC output wires during reassembling it. Now, oscilloscope turns on and turns off and cycle goes on. Any suggestion will be highly appreciated. Thanks.

• 
  @grahamnichols14167 күн бұрын

  Love the inclusion of the instructions and input voltage specs on the rear of the case really took this project up a notch. NICE.

• 
  @andyvardy89277 күн бұрын

  "Taking a 3" floppy"

• 
  @TomLeg13 күн бұрын

  Should have used right-angle BNC connectors to avoid the cable sticking out so far :-) Love the enclosures

• 
  @thanhnguyen-xi8fq13 күн бұрын

  Each time you change the resistor scale x1 x10 x100 etc... you need to ZERO it first.

• 
  @mr1enrollment18 күн бұрын

  edge connectors best cleaned with a Pink Pearl eraser

• 
  @samuelolanrewaju351018 күн бұрын

  Can you please do a video of the Brother Ptouch D600 printer as I need to fix it

• 
  @hamishdavidson336825 күн бұрын

  Im looking for the original leads being Banana no shroud?

• 
  @adiltheprodigy823526 күн бұрын

  It gives me 2 instead of 8 😢 in the division

• 
  @brouwereric64426 күн бұрын

  I love the enclosures. Nice job.

• 
  @Dark_Jaguar28 күн бұрын

  I wonder how possible it would be to install a digital dial to replace the up/down arrow controls for temp. That's about the only thing I'd want to change on this, since I absolutely love dial controls for sheer speed of altering things like airflow and temp changes.

• 
  @jomimaro1Ай бұрын

  Hi! Really nice video. Do you know if the electronic circuit works at 3 volts or the capacitors work as part of a voltage booster? Thanks :)

• 
  @billcrm003Ай бұрын

  Can you provide a connection diagram of the 6 pin LEMO connector to the output head? I recently get a output head with cable completely cut off and I don't know the connection to rebuild it. Thanks!

• 
  @andrzej3511Ай бұрын

  Why You talk so much about nicotine? (You were probably smoking like a steam locomotive a few years ago and now you pretend to be holier than the Pope...) Is it an anti-smoking ad or a clip about the scope service? Wouldn't it be easier simply to disassemble the casing and external elements, knobs, buttons, etc., throw it all into the dishwasher and after an hour take it out clean, smelling like it came straight from the factory?

• 
  @amtc4ihs2005Ай бұрын

  I know it isn't a toy car, but I may I kindly ask you about a very special and unique toy from my childhood, about mid 2000's?

• 
  @patmx5Ай бұрын

  It’s a shame Tek used ground eggshells (at least it seems that way given their fragility) to make their knobs. These poor 500/5000 units seem to live a rough life. Nice work making up that casting mold!

• 
  @kaja332Ай бұрын

  Koja je baterija

• 
  @kevinsajadi2879Ай бұрын

  Hi There is some videos in youtube showing dell or hp psu hot plugs convert to bench power suply. They could run the psu hot plugs by connecting some pins but they just could run them to take a small curent not the maximum curent. Could you please tell me how to run my "hp 2450w hstns-pr16 platinum hot plug" and "hp 2650w hstns-pr42 platinum hot plug" into a bench power suply to take the maximum curent and power? Kind regards Kevin

• 
  @electrotools8083Ай бұрын

  please make a tutorial that how to connect to serial interface and send serial data to computer . thanks!

• 
  @nodak81Ай бұрын

  Thank you for this video! I needed to know where the IR sensor was located and I couldn't see through the plastic to locate it, not even with a really bright light. I need to block it with tape so it can't receive errant signals from another device's remote.

• 
  @garito175Ай бұрын

  I just wonder where are you located??? To see if could repair my speaker Joel flip 3 asap

• 
  @garito175Ай бұрын

  Yo quiero saber donde puedo comprar esa parte que se dañó al speaker y cómo se llama esa parte que se dañó???

• 
  @ROGUPAАй бұрын

  Mr. I have the HT-R550, its displays turns off after a few minutes. I am not a certified technician, nevertheless I found out when the Cirrus Logic IC CS42518-CQZ got heat the displays fails... Applying circuit board cleaner the propelent cools it down and the display turns back on AGAIN for a moment... At this point I have the circuit diagrams and I already ordered a replacement chip JUST IN CASE the IC is damaged. I suspect it is not and MAYBE a surrounding capacitor is. I'll try to check the capacitors... in the meantime, I'll appreciate any comment regarding this issue. Greetings, from MX Rodrigo

• 
  @gixerags7502 ай бұрын

  That cable stripper looks next level shit !!! Nice.

• 
  @thatampguy2 ай бұрын

  Brilliant use of that flux pen!did any of the silicon grease go over the wiper or track?

• 
  @NearFarMedia2 ай бұрын

  I used a plastic safe white lithium grease and yep, put it thinly on the wiper and track, like the manufacturer did originally. That way the track will be lubricated to reduce wear. As a side note, I don't think it matters for trimpots, but avoid using silicone grease in switches, apparently any arcing in the switch can slowly turn the silicon in the silicone grease into silicon carbide which is an insulator and very(!) hard and abrasive....

• 
  @mikemoran54392 ай бұрын

  I just bought one of these and it works great, but i want to preserve it. Would you happen to have a list of all the caps you replaced (new ones)?

• 
  @mikemoran54392 ай бұрын

  Nevermind! I just read the description! Haha

• 
  @luisguadalupe75552 ай бұрын

  What's grease to you recommend using?

• 
  @NearFarMedia2 ай бұрын

  A plastic safe grease, white lithium grease is good.

• 
  @fivestar22272 ай бұрын

  To open the shell you must remove the 2 rubber wall hang plugs and the 2 raised stand offs (feet) to expose the 4 screws. Use your fingernails to pry open both sides (left & right short ends) then pry the bottom apart (thinner edge opposite of the antennas). If you want to remove the board there are 2 screws (near lights and wan port) and 2 antenna mounts to remove.

• 
  @ismaelmorin82212 ай бұрын

  Hola..desde celaya GTO.. México..es normal que los receivers onkio..se calienten en encendido.. gracias..IMG

• 
  @German_byte2 ай бұрын

  There’s no isolation between input and output is there. Not that there’s a 240 volt input.

• 
  @PlanetRuncorn2 ай бұрын

  when i turn mine on the battery voltage reads 7.1v even though its a new battery . dont know if this makes a difference , and a 470uf cap reads 66470uf ??? any ideas why

• 
  @yakup34292 ай бұрын

  Hello, is it possible to connect this tester to a PC?

• 
  @uglahhmane2 ай бұрын

  Ive juat gotta say I would not ever pump that cleaner that hard. High risk.

• 
  @NearFarMedia2 ай бұрын

  If a bit of string on the end of a bit of plastic can scratch your fiber, you need to purchase better fibers. Nearly 10 years in the game and I have yet to scratch or damage a single fiber.

• 
  @uglahhmane2 ай бұрын

  @NearFarMedia Tell that to Raytheon or Northrop Grumman. Licensed avionics technician. Just giving my 2 cents. QC at any airline would have a heart attack if they saw that. Maybe just ignorance on our end, but we are trained to clean with great delicacy when you're dealing with extremely expensive fiber that cannot be repaired.

• 
  @darukun41792 ай бұрын

  really really nice. next time try to put some reverb on that 'fuull bridge rectifieerr'

• 
  @marcelolopes13472 ай бұрын

  Do you know any replacements for the rotary switches?

• 
  @consultordegenteplinioeng92302 ай бұрын

  Thanks from Brasil!!

• 
  @magatsu822 ай бұрын

  Thank you so much for this!

• 
  @SwitchingPower3 ай бұрын

  I just relapsed the battery in the same machine with "Varta 2/V150H" that is a drop in replacement that is still in stock at RS Components

• 
  @Traumi993 ай бұрын

  i actually have an tds 644b with 684 board(the original board has been take a shower on capsfluid and drop the magic smoke) i change it his board and the caps in new boar, but still not working (only turn on and off every second) maybe need to check power supply too

• 
  @marcelojordao66023 ай бұрын

  ola !! tudo bem? uma pergunta, voce consegue detectar o efeito early? grato um abraço!

• 
  @absurdengineering3 ай бұрын

  Would you be able to share what connectors are you using (mfg/series) and what particular crimper? I’ve been thinking about getting Japanese crimpers for some common contacts.

• 
  @absurdengineering3 ай бұрын

  It is possible to buy bulk white toner and fill up one’s own old cartridge. For front panels I’ve replaced the Y cartridge with white, getting CMWK capability. The cartridges can be reordered to get good coverage of white on black etc. It just needs some small changes to the postscript file sent to the printer. Why postscript? So you can fully control what’s drawn with what color. Otherwise the Adobe+Windows color management messes it up.

• 
  @absurdengineering3 ай бұрын

  Free alternatives: For drawing - Inkscape. For public mechanical cad (2D and 3D) - OnShape.

• 
  @DenKloge13 ай бұрын

  Okay fint nok. Alle kan skille en computer ad og sætte sin finger på hardwaren og sige en hel masse kloge ord om det.

• 
  @rico58703 ай бұрын

  Hi mate! thanks for the video! Just a question, where did you get the PSU schematic? Im struggling for a while to find PSU schematic for TDS380 and 420A. Gday

• 
  @ericpilboue32763 ай бұрын

  J'adore, je suis pas au niveau pour en avoir besoin maintenant. Ce que j'aime le plus c'est la somme de travail et les progrès accessibles aux amateurs, fini les boites en pcb, les circuits en l'air, etc. Very professional work. I have seen many power meter on ebay without sensor, so at this time i play with ad8307 and analog voltmeter. Thank for sharing your knowledge

• 
  @SuperSergio55553 ай бұрын

  hi, can you replace it with a usb-c instead?

• 
  @Willow1w3 ай бұрын

  I took apart mine and looks like now they put in there a controller in a SOP package, SMD leds and passives. No power LED. But solder joints are very bad, there is barely any solder, you can see bare copper pads. Also this thing is USB1.1! Max rate 12 Mbit/s. Shameful!