@@starlinggibson4117 if you change the hall angle setting, the blinky mode turns off. Better say, it does not show on the screen “Blinky” anymore, therefore is not allowed to be used in stock racing.
@mikestewart475213 күн бұрын
👍👍 NOT made in China! ❤️🙏
@timothypence119518 күн бұрын
What is the motor limit?
@martinbollenbacher306620 күн бұрын
Awesome Video but a few days late😄. Unboxed mine on Wednesday and used it first time on Friday. Easy to use and reliable Speedo. At the moment it is installed in my Stock 2wd Buggy with a 13.5t Motor. Testing on Friday and a Race on Sunday without any issues. 👍 I am looking forward to see more content about this controller.
@floridalife7877Ай бұрын
Is there a toe chart for the 1 degree block like there is for the 3 degree block in the manual?
@maxgotzlrc2266Ай бұрын
Hello, I don’t think so, altough the toe chart can aply to the 1° block, just subtract 2
@peterpirolt6997Ай бұрын
Don't have a question about the Arms but why do you run the shock on the shocktower on the lower holes ?
@maxgotzlrc2266Ай бұрын
Hey, sorry if I haven’t answered your question also last week in France, but I use the lower holes to make the car more stable.
@bonxiegizmo2 ай бұрын
Just wondering why I have no reading of motor temperature. All is connected, including sensor wire.
@maxgotzlrc2266Ай бұрын
Hello, could you give me more info about what motor are you using? It is possible your type does not have a temp sensor and therefore does not support temp monitoring.
@bonxiegizmoАй бұрын
ZTW , Ruddog and Fantom. All 6.5 and 7.5
@mateematee72472 ай бұрын
Hezka jizda💪👏👍gopro?
@gmourt2 ай бұрын
Hi, at the 1st example, you select boost 1 = 10 and boost 2=15. On the diagram I can understand that the boost 2 value is "absolute", means counting from zero, thus the total boost is 15 (not 10+15=25). But, at the 2nd example, boost 1 (10) and boost 2 (10) values are cumulative according to the diagram (10+10 = total 20). I wonder why this difference.
@maxgotzlrc22662 ай бұрын
Hello, thank you for the question. I have made a mistake on the setting and that’s why I corrected my talk with a little note in the video saying “*Double value”. What I meant to show was Boost1 at 10 and Boost2 at 20.
@drewhamilton69063 ай бұрын
Very helpful information, thank you
@tek007328823 ай бұрын
How about the 2,0mm chassis? It's just too expensive to buy and try out..
@bertrandferrere19944 ай бұрын
Thanks a lot : very clear and informative vidéo ! I'm currently waiting for my Elceram Esc and my new car also : checkin tracking every hour 🙂
@stackitwithbricks71034 ай бұрын
Love your vids keep going mate 🎉
@macmondo744 ай бұрын
Thanks Max these videos are gold. Very good information.🙏👍
@Slatanicmushroom4 ай бұрын
Very well explained, thank you!
@eddiejones23284 ай бұрын
You mentioned that you cannot use the kit pills with the 1degree block which ones can you use then?
@maxgotzlrc22664 ай бұрын
You cannot use the same settings, because the D block is narrower compare to the kit one. If you used the same inserts as on the kit one (lets say outside on the C block and inside on the D block), you would actually get toe-out on the rear suspension, which is not desired.
@eddiejones23284 ай бұрын
Oh okay I thought you meant eh pills them self were different
@extec1014 ай бұрын
could you recomend the short chassi option for a xb2-22 im using the kit one right now but got an idea to use the short chassie to move the gearbox forward and move rear hubs back in the arms to keep the overal wheelbase the same as kit version but the weight of motor and gearbox more forward in the car to make it rotate more free in the back as the car is used for carpet and high traction astro.
@maxgotzlrc22664 ай бұрын
yes, this can be a good option if you run on high grip. Keep in mind, that the 2024 car has different chassis compare to the the '22
@extec1014 ай бұрын
need to get that carbon motor mount it looks sweet. what might the weight savin be in grams compared to the alu ones?
@timothypence11954 ай бұрын
Need to improve volume in future videos, please.
@user-tf4sx5oq6d4 ай бұрын
Can you do a video on the 1deg D block,what it does and when to use it.thank you
@Aftehours070835 ай бұрын
Thanks, it can be hard for people new to setup to understand the difference between high and low and how these changes affect roll center.
@wimdehertogh2289 Жыл бұрын
What setupboard is this?
@maxgotzlrc22664 ай бұрын
I use the HUDY setup boards for all of my classes.
@jb-elektronik Жыл бұрын
New nitride brushless regulator made in Elceram: kzread.info/dash/bejne/dK2Fscyqc82veMo.html
@christianryser34202 жыл бұрын
Und benötigt man Haftmittel?
@christianryser34202 жыл бұрын
Wo kann man diese Räder kaufen?
@kinovara78812 жыл бұрын
Hi, thats nice driving. Please, what pinion/gear and motor are installed?.
@maxgotzl43492 жыл бұрын
Hi, I am still using 23t/78t (pinion/spur gear) with a 6,5T motor, that seems to be the optimal setup for most carpet tracks for me. ;)
@avgguyfixingstuff49392 жыл бұрын
Excellent driving, would you share any of your setup specs? caster camber etc f/r
@shanepond64332 жыл бұрын
Do these need a sauce to work?
@extec1014 ай бұрын
no no sauce needed.
@shanepond64332 жыл бұрын
Do these need a sauce compound to work properly
@extec1014 ай бұрын
no they work great just as is and most of the time got a longer runntime then regular rubber tires like cactus. just that the pinion sometimes need to be changed a tooth up or down to keep the rollout as tires get worn out.
@danielgro49663 жыл бұрын
I just got my self a set of buggy foam tires. I am currently trying to figure out if the tire in the front needs to be wide ore narrow. How are you running it? I am not able to figure it out from the video.
@extec1014 ай бұрын
in front use wide rims for the foams and for me i prefere to grind down the inner ribbs on the rim both front and back as well as the innerside shoulder of the rim (leave the outside edge to protect tires from hitting track markers) to max out the wideness of the tire and make the inside part of the tire to be more in contact with the ground rather then during heavy loading tuck he tires and start to ride on the edge of the rim.
@mrtgeary82683 жыл бұрын
👍🏻
@stanislavkozak28063 жыл бұрын
Najs!!!!
@kvidoklikar56683 жыл бұрын
First!!!!
@tomassochurek89593 жыл бұрын
Mega dobrý 🤟
@stanislavkozak28063 жыл бұрын
Nádhera! Dávám odběr.
@karelnovotny23873 жыл бұрын
How fast does it go?
@maxgotzlrc22663 жыл бұрын
It goes very very very fast. It could hurt if it hits you 😵
Пікірлер
Slicks ?
Are the Hall settings locked in blinky mode
@@starlinggibson4117 if you change the hall angle setting, the blinky mode turns off. Better say, it does not show on the screen “Blinky” anymore, therefore is not allowed to be used in stock racing.
👍👍 NOT made in China! ❤️🙏
What is the motor limit?
Awesome Video but a few days late😄. Unboxed mine on Wednesday and used it first time on Friday. Easy to use and reliable Speedo. At the moment it is installed in my Stock 2wd Buggy with a 13.5t Motor. Testing on Friday and a Race on Sunday without any issues. 👍 I am looking forward to see more content about this controller.
Is there a toe chart for the 1 degree block like there is for the 3 degree block in the manual?
Hello, I don’t think so, altough the toe chart can aply to the 1° block, just subtract 2
Don't have a question about the Arms but why do you run the shock on the shocktower on the lower holes ?
Hey, sorry if I haven’t answered your question also last week in France, but I use the lower holes to make the car more stable.
Just wondering why I have no reading of motor temperature. All is connected, including sensor wire.
Hello, could you give me more info about what motor are you using? It is possible your type does not have a temp sensor and therefore does not support temp monitoring.
ZTW , Ruddog and Fantom. All 6.5 and 7.5
Hezka jizda💪👏👍gopro?
Hi, at the 1st example, you select boost 1 = 10 and boost 2=15. On the diagram I can understand that the boost 2 value is "absolute", means counting from zero, thus the total boost is 15 (not 10+15=25). But, at the 2nd example, boost 1 (10) and boost 2 (10) values are cumulative according to the diagram (10+10 = total 20). I wonder why this difference.
Hello, thank you for the question. I have made a mistake on the setting and that’s why I corrected my talk with a little note in the video saying “*Double value”. What I meant to show was Boost1 at 10 and Boost2 at 20.
Very helpful information, thank you
How about the 2,0mm chassis? It's just too expensive to buy and try out..
Thanks a lot : very clear and informative vidéo ! I'm currently waiting for my Elceram Esc and my new car also : checkin tracking every hour 🙂
Love your vids keep going mate 🎉
Thanks Max these videos are gold. Very good information.🙏👍
Very well explained, thank you!
You mentioned that you cannot use the kit pills with the 1degree block which ones can you use then?
You cannot use the same settings, because the D block is narrower compare to the kit one. If you used the same inserts as on the kit one (lets say outside on the C block and inside on the D block), you would actually get toe-out on the rear suspension, which is not desired.
Oh okay I thought you meant eh pills them self were different
could you recomend the short chassi option for a xb2-22 im using the kit one right now but got an idea to use the short chassie to move the gearbox forward and move rear hubs back in the arms to keep the overal wheelbase the same as kit version but the weight of motor and gearbox more forward in the car to make it rotate more free in the back as the car is used for carpet and high traction astro.
yes, this can be a good option if you run on high grip. Keep in mind, that the 2024 car has different chassis compare to the the '22
need to get that carbon motor mount it looks sweet. what might the weight savin be in grams compared to the alu ones?
Need to improve volume in future videos, please.
Can you do a video on the 1deg D block,what it does and when to use it.thank you
Thanks, it can be hard for people new to setup to understand the difference between high and low and how these changes affect roll center.
What setupboard is this?
I use the HUDY setup boards for all of my classes.
New nitride brushless regulator made in Elceram: kzread.info/dash/bejne/dK2Fscyqc82veMo.html
Und benötigt man Haftmittel?
Wo kann man diese Räder kaufen?
Hi, thats nice driving. Please, what pinion/gear and motor are installed?.
Hi, I am still using 23t/78t (pinion/spur gear) with a 6,5T motor, that seems to be the optimal setup for most carpet tracks for me. ;)
Excellent driving, would you share any of your setup specs? caster camber etc f/r
Do these need a sauce to work?
no no sauce needed.
Do these need a sauce compound to work properly
no they work great just as is and most of the time got a longer runntime then regular rubber tires like cactus. just that the pinion sometimes need to be changed a tooth up or down to keep the rollout as tires get worn out.
I just got my self a set of buggy foam tires. I am currently trying to figure out if the tire in the front needs to be wide ore narrow. How are you running it? I am not able to figure it out from the video.
in front use wide rims for the foams and for me i prefere to grind down the inner ribbs on the rim both front and back as well as the innerside shoulder of the rim (leave the outside edge to protect tires from hitting track markers) to max out the wideness of the tire and make the inside part of the tire to be more in contact with the ground rather then during heavy loading tuck he tires and start to ride on the edge of the rim.
👍🏻
Najs!!!!
First!!!!
Mega dobrý 🤟
Nádhera! Dávám odběr.
How fast does it go?
It goes very very very fast. It could hurt if it hits you 😵
Wow, awesome! We want more