Пікірлер

• 
  @RationallySkeptical4 күн бұрын

  It would have been better if you had included showing how the device will actually give the watt rating of the cable [PD 100W, for example] as well. Knowing whether a cable is rated for 140W or 100W is arguably more important than just knowing if a cable is overly resistive. Also, please make another video where you explain how to accurately measure power bank capacity by using the device, calulating to Wh and compensating from the nominal 3.7V battery to the 5V usb current. There arent any good videos that are solely a tutorial on calculating power bank capacity with the FNIRSI FNB58.

• 
  @tonysfun4 күн бұрын

  I don't know when I'll have time to record another video 4 U. But as the video stated, the 100W cable was the best cable I have. For my needs this FNB58 does exactly what I purchased it for. It does much more, but I move quickly to new ideas and I don't have any cable that is 140W, sorry. Why don't you buy this useful tool and make a video, please send me where the video is, so I can learn something from you. FNB58 is on sale: fnirsistore.com/product/fnirsi-fnb58-usb-tester-voltmeter-ammeter/ Even less here: www.amazon.com/Voltmeter-Ammeter-Protocol-Trigger-Voltage/dp/B0CNXJBLHP/ref=sr_1_7?crid=P2RV9BKFME5P&dib=eyJ2IjoiMSJ9.rqIXBILoZAtkrJ-yUk1UgCgq-wB7vsgGWgrmqbmPpGdRRQ33TqH7CqtlmM4VhF-9JwCW4EltTb6J9_l7Ft119b7w508Lmj8VDx0J5lFQqS6z2_D45ORLGjxv0CuNl7AH0352FFlvsqaSoNGe53hCgQfIQaHQyFZBCe-uzrxvAGfdGbpNtUO5QCoIkWFoy6yh.F9fKxDPHwn6Qfcd3InzELeYono85nIi7Fe7IW8XMwKo&dib_tag=se&keywords=FNIRSI+FNB58+USB&qid=1719327635&sprefix=fnirsi+fnb58+usb%2Caps%2C251&sr=8-7 You have a great day!

• 
  @abdlaziz_9 күн бұрын

  just in case if anybody sees this comment and might benefit from this i found multiple vidoes about this topic this is for A to type C : kzread.info/dash/bejne/oJ-kj6NxptivaNY.html and there is also a way to check type C to type C cable also : kzread.info/dash/bejne/oop1q9STor2_pZs.html

• 
  @abdlaziz_10 күн бұрын

  great video .. i gotta ask tough .. why is it necessary to put a resistor on the right side ? there has to be a simpler way than this right?

• 
  @tonysfun10 күн бұрын

  My son found this part somewhere on the net and we plaid with the bad "how to" and found that the best calibration was to use a resistor between 25 to 100 Ohms.

• 
  @abdlaziz_9 күн бұрын

  just in case if anybody sees this comment and might benefit from this i found multiple videos about this topic this is for A to type C : kzread.info/dash/bejne/oJ-kj6NxptivaNY.html and there is also a way to check type C to type C cable also : kzread.info/dash/bejne/oop1q9STor2_pZs.html by the way didn't you say it was an 8 ohm resistor the one that you chose in this video ? and what was the gauge of the wire that you soldered to the usb connector? again great video and thank you for the quick reply !!

• 
  @tonysfunАй бұрын

  I'm looking for a working APP for my phone that would operate this robot! I've downloaded many other versions - same looking robots sold under other brand names - but I can't find any apps that work. I get to connect just fine, but none of the buttons do anything! If any of you out there have a solution, please let me know. Thanks!

• 
  @johndevires5911Ай бұрын

  Would have been nice to see the other side of the pcb also.

• 
  @VladimirOpltАй бұрын

  Excellent Tony , I liked really. Show it how runs in the terrain . . .

• 
  @tonyfleming4560Ай бұрын

  I'll try to make a video later on.

• 
  @nikkisixx2878Ай бұрын

  All your videos are bullshit. You don't keep track of focus and blame it on your camera?! Who is the boss in your place?

• 
  @HariWiguna2 ай бұрын

  Great job Tony!

• 
  @paris97862 ай бұрын

  Hello, I have a problem with the LCR T7, when I turn it on, it gives me zenor 13.6v without connecting anything to it.

• 
  @tonysfun2 ай бұрын

  Did you charge the LCR? Also, try to put a 1Kohm resistor before you turn LCR on?

• 
  @paris97862 ай бұрын

  Hello, I have a problem with the T7, when I turn it on, it gives me zenor 13.6v without connecting anything to it.

• 
  @tonysfun2 ай бұрын

  Charge the LCR first and put 1Kohm resistor between pins 1 and 2, than turn the LCR on. And the same after 1Kohm between pins 2 and 3 and also pins 1 and 3.

• 
  @paris97862 ай бұрын

  @@tonysfun Thank you, my friend. I will try tomorrow and update you on everything

• 
  @tonysfun2 ай бұрын

  @@paris9786 Sounds good.

• 
  @paris97862 ай бұрын

  Hello, I tried the experiment and it is as follows. Firstly, 1-2 gave me the resistance value of 1K. Secondly, 2-3 gave me the zener AK. Thirdly, 1-3 gave me the zener AK. How can I solve this problem?

• 
  @tonysfun2 ай бұрын

  @@paris9786 Did you measure something like a capacitor and your problems started right after that? If yes, you forgot to completely discharge the capacitor! For that, you have no fix and just buy a new one. Please also see this video, before you buy something else: kzread.info/dash/bejne/o2iEj6SelMvRqpc.html&ab_channel=TonyFleming

• 
  @LandersWorkshop2 ай бұрын

  I tried releasing the clips which is successful BUT the case won't come apart as there's a black, oval object that is preventing the case from removing completely. It will not pull off either. Very tricky to work out.

• 
  @tonysfun2 ай бұрын

  Try to see all 4 videos. You might find solution there. See my comments below.

• 
  @LandersWorkshop2 ай бұрын

  @@tonysfun Hey, I tried but cannot see in any of your videos how you remove the bottom from the top.

• 
  @tonysfun2 ай бұрын

  @@LandersWorkshop I know that the videos are several years ago, so I don't remember all the details, but there is enough info, so watch them all, because I wasn't at the time very organize in my videos - sorry.

• 
  @LandersWorkshop2 ай бұрын

  @@tonysfun Unfortunately this part that is on mine is not on yours so I think it is a slightly different version.

• 
  @tonysfun2 ай бұрын

  @@LandersWorkshop Sorry, but if I can speculate, look for a screw or one more clip? I remember that sometimes the clips you pushed to open snap back to a locked position!? What is the model number? Is it newer model?

• 
  @argentinomacrifuevidaltamb37723 ай бұрын

  Excelente video. Gracias por compartir.

• 
  @byoung15203 ай бұрын

  Mine turns on when connected to the battery and connect K to the negative but after a few seconds it shuts off

• 
  @tonysfun3 ай бұрын

  You need to put a small pushbutton switch, like in my video, because the "K" on the PCB is looking for 1CLICK or 2 CLICKS! If you wire the K to MINUS it will get confused! Hope that you can make it work!

• 
  @natesgarage3 ай бұрын

  Thanks, Tony! Your creations are always very neat and clean. I'm still wishing for a laser cutter of my own.

• 
  @MAX_Brother3 ай бұрын

  Hi, can you write down resistors value on the board? They all must have the same value.

• 
  @tonysfun3 ай бұрын

  I was looking for the values of the resistors, but my microscope with my eyesight.... I couldn't read the values. I measured several of them and the value is 1Kohm. Hope that this helps.

• 
  @jairtenatrujillo55103 ай бұрын

  hola me podrías ayudar con la resistencia R2, se me ah perdido en una caída y le falta la R2 :(, quisiera saber el código para reemplazarlo. estaría muy agradecido :)

• 
  @tonysfun3 ай бұрын

  Sorry do not know your language. Try to translate to English.

• 
  @jairtenatrujillo55103 ай бұрын

  @@tonysfun Hello, could you help me with the R2 resistor, I lost it in a fall and the R2 is missing :(, I would like to know the code to replace it. I would be very grateful :)

• 
  @tonysfun3 ай бұрын

  The CERAMIC resistor is 10W 8 ohms. I hope that is what you needed. Have a great day.

• 
  @jairtenatrujillo55103 ай бұрын

  @@tonysfun R2 is on the other side, please help me :)

• 
  @tonysfun3 ай бұрын

  On my tester is only one ceramic resistor. On the right bottom corner is a green connector - that is battery input, not a resistor!

• 
  @HE3AMEHIM3 ай бұрын

  Ваш тестер не калибруется перемычкой у вас подделка на чипе М644 . Который дешовая копия не начто неспособна.

• 
  @tonysfun3 ай бұрын

  Sorry, I do not know your language.

• 
  @HE3AMEHIM3 ай бұрын

  @@tonysfun Your tester is not calibrated by a fake jumper on your M644 chip. Which a cheap copy is not capable of doing.

• 
  @victorbarrera-xq4xl4 ай бұрын

  What should a good heating element read and what should a bad one read on a multimeter ?

• 
  @tonysfun4 ай бұрын

  If you use Ohm position on your multimeter you should get some readings and if you don't get any readings than you need to fix or replace the heating element. Did you watch both videos? Also see this video: kzread.info/dash/bejne/n2WNq7mOYNzKYdo.html&ab_channel=TonyFleming

• 
  @GolfBala4 ай бұрын

  I cloned 200 go to 500 go takes 5 mins but from 500 to 1tb take forever Is that normal?

• 
  @tonysfun4 ай бұрын

  Yes, it is a very slow duplicator!

• 
  @DiyintheGhetto4 ай бұрын

  That looks like fun Tony. Now if we can do it in 3D Printing i'll make one.

• 
  @tonysfun4 ай бұрын

  Join a Maker's Club or find a friend with laser cutter and download the files. Or you can design the box in a free version using Fusion 360.

• 
  @alex-pi3vn4 ай бұрын

  disassembled this tester. The microcontroller is a Chinese clone of Atmega 328 / LGT8F328.ESR, it shows sometimes no. And that’s not correct. Schottky diodes are identified as a resistor. Maybe the firmware is normal, but the controller is crap. It needs to be replaced with an Atmega 328

• 
  @tonysfun4 ай бұрын

  I'm using it sometimes and it works well. I compared it to several other LCR testers and found it to be accurate. Did you remove the original Atmega chip and installed the real Amega chip? D you have a video where you did this? Thanks for your comment.

• 
  @alex-pi3vn4 ай бұрын

  @@tonysfun I only found your video on KZread. There are no firmware or circuit diagrams for this tester. I haven’t changed the controller yet. I’m just examining the board Maybe you have an original controller on the board, that’s why it works normally. I don’t have an inscription on the controller, it’s worn out. I'll try to change the controller, maybe I can fix it so it works correctly My translation may not be very good. I’m just from Ukraine

• 
  @tonysfun4 ай бұрын

  I understand your English just fine. I hope your country end the war and Rusha leaves! I do not know if my tester has the original or a copy board, but in China they copy everything including from other China manufactures and just rename it.... I'm not gonna disassemble my tester to find out what board is in mine. What is wrong with your tester?

• 
  @maf2Ай бұрын

  @@tonysfun I bought this. This meter MTT-V1 detects a 3.3V Zener diode as two diodes. It detects an inductor but overestimates the value 2-3 times. This is not an ATMega-based tester,

• 
  @victorbarrera-xq4xl4 ай бұрын

  Do you know where we can purchase this heating element at ? I’ve been trying to find one similar but can’t seem to find any online

• 
  @tonysfun4 ай бұрын

  I do not know where you can buy one, but you can see 2 more videos here: kzread.info?search_query=Plastic+Welder+from+Harbor+Freight+tony+fleming

• 
  @erinnoyd11474 ай бұрын

  4.5 billion years of spinning and they asked why? I love how this all ended. Im glad everyone got to see the true meaning of a Halo 😇 (Solar System).

• 
  @EvgeniX.4 ай бұрын

  just ordered myself one. cheaper and more capable than the "C2C caberQU". thanks!!

• 
  @tonysfun4 ай бұрын

  What tester did you get? Have you seen FNISRI? kzread.info/dash/bejne/nW2Gl6uRZLDRldY.html&ab_channel=TonyFleming

• 
  @EvgeniX.4 ай бұрын

  ​@@tonysfunnah too expensive 4 my needs.. got the treedix one for data pins, also have type-c volt/ampere meter for the charging test. covers most of my use cases. anyway thanks for the heads up

• 
  @alexpol19584 ай бұрын

  Появилась ли новая прошивка? Firmware????

• 
  @tonysfun4 ай бұрын

  Sorry, but I can't read your question. If you are asking how to update the firmware? I do not know how to do that.

• 
  @AndreasSpiess5 ай бұрын

  I did not know you had a channel. Cool video!

• 
  @tonysfun5 ай бұрын

  Noting very important on my channel but thank you !

• 
  @GodriaR5 ай бұрын

  Thank you for the video, Is there a pre-made consists load, I can buy from Aliexpress? Thank you

• 
  @tonysfun5 ай бұрын

  Nothing to buy but a resistor as seen in the video.

• 
  @tonysfun5 ай бұрын

  Here is where the SCHEMA is at: kzread.info/dash/bejne/o5qh2I-reK7Fgrg.html Use ScreenShot or PRT SCN button on your keyboard to copy the screen and paste it into word or other editor, print it and there is your schema.

• 
  @richardchildress90315 ай бұрын

  do you have the circuit for sale

• 
  @tonysfun5 ай бұрын

  I'm sorry, I do not sell anything. But the shema is on the youtube, that is how I made it. Just watch the video and make notes and it is fairly simple schema. I used a PRNSCN button on keyboard to print the schema. You can make one at a time - you need 4 of them and or solder them on one larger PCB. If you do not solder components, ask a friend or try to find someone in your city who can make it for you - like TV repair shop....

• 
  @medeo98135 ай бұрын

  Hello. Could you write me link fo Android and Windows app for this meter? On official website i can't find app. Thanks

• 
  @tonysfun5 ай бұрын

  This is the website: drive.google.com/drive/folders/1hOv76usYlKQwLIst0oDn_zbYuPlt8iEE

• 
  @medeo98135 ай бұрын

  @@tonysfun your Google drive is closed for me

• 
  @tonysfun5 ай бұрын

  @@medeo9813 I have no problem downloading all of the software and the manual.

• 
  @medeo98135 ай бұрын

  @@tonysfun Got it. Appreciate

• 
  @Andyfun20105 ай бұрын

  Kann der FNB58 mit aktueller Firmware nur 120 Watt? In den Spezifikationen steht maximal 120 Watt! Das schwächste PD3.1 Ladegerät kann 140 Watt! PD3.1 selbst geht bis 240 Watt.

• 
  @allcheckout5 ай бұрын

  Teste häufig über 140W mit original FW ohne Probleme

• 
  @JagMan9035 ай бұрын

  I just bought this tester and wanted to test a "26800mah" power bank I bought from Amazon. I don't quite understand how to read the results that's right in front of me. Lol. Is it a 9900mAh or 19600mAH capacity? Screen says the following: Battery CAP Calculation Group: 01 Time: 0 days 14:36:41 CAP: 9.92364 Ah NRG: 80.5495 Wh BAT Vol: 3.7V Conv Eff: 90% Results: 19.5931 Ah Thanks!

• 
  @tonysfun5 ай бұрын

  Good question. I do not know the answer. I tried to recreate what you did, but I'm not getting the same results you have.

• 
  @edgi556 ай бұрын

  Thanks so much Tony for this very helpful video. All the best

• 
  @tonysfun6 ай бұрын

  All the best also for you and your family.

• 
  @derdoktor71236 ай бұрын

  Thanks for your video! I tried it with my electronic load and discovered that it works only with 1 A load current, not with 2A. The current measurement of the FNB58 is precise up to 4 digits!

• 
  @tonysfun6 ай бұрын

  Here is the clock download: github.com/hwiguna/MorphingClock_for_MatrixPortal Thanks to Hari Wiguna who made it possible.

• 
  @martien-io6 ай бұрын

  I have bought the IKEA rechargeable batteries recently, rumor has it (and also several tests show) that those are rebranded Panasonic Eneloop Pro batteries for a fraction of the price, so far I’m very happy with them!

• 
  @tonysfun6 ай бұрын

  I found these: www.ikea.com/us/en/p/ladda-rechargeable-battery-hr06-aa-1.2v-00509814/ on the web, BUT they are ONLY 1.2V, not 1.5V like mine.

• 
  @Badvision6 ай бұрын

  Now that i know the board is moving, i just slammed it once and it works again 😂

• 
  @tonysfun6 ай бұрын

  Great news and you saved some $$$

• 
  @tomnewtnt57186 ай бұрын

  Jak dokonać kalibracji tego testera

• 
  @tonysfun6 ай бұрын

  There is only a SELF TEST AND CALIBRATION during the power up sequence. I tried to run the calibration test, but there isn't any option to do so. Also see my other video kzread.info/dash/bejne/Zndso8OjXcTFptI.html . Have a great day.

• 
  @tonysfun6 ай бұрын

  Here is the sketch: // Define the pin numbers for the relays const int relay1Pin = 2; // Connect the first relay to D2 const int relay2Pin = 3; // Connect the second relay to D3 void setup() { // Set the relay pins as OUTPUT pinMode(relay1Pin, OUTPUT); pinMode(relay2Pin, OUTPUT); // Turn off the relays initially digitalWrite(relay1Pin, HIGH); // HIGH for active LOW relay digitalWrite(relay2Pin, HIGH); } void loop() { // Turn on the first relay (lightbulb 1) for 5 seconds digitalWrite(relay1Pin, LOW); // LOW for active LOW relay delay(1000); // 5 seconds delay digitalWrite(relay1Pin, HIGH); // Wait for 2 seconds delay(1000); // Turn on the second relay (lightbulb 2) for 5 seconds digitalWrite(relay2Pin, LOW); delay(1000); digitalWrite(relay2Pin, HIGH); // Wait for 2 seconds before repeating the loop delay(1000); }

• 
  @chriskwakernaat23287 ай бұрын

  i only wish the thing was in english , lol.

• 
  @tonysfun7 ай бұрын

  But it works and soon you don't need any help to use it. By the same token they could make English version but they are not thinking about you and me, just themselves!

• 
  @georgef77547 ай бұрын

  If only somebody could build a full size version.

• 
  @tonysfun7 ай бұрын

  There are several companies that make these in much larger size! Just search the Internet and find out.

• 
  @tonysfun7 ай бұрын

  Here is the simple code for Arduino IDE: #include <MotorDriver.h> MotorDriver m; void setup() { } void loop() { //labels FORWARD BACKWARD m.motor(1, FORWARD, 75); m.motor(2, FORWARD, 75); m.motor(3, FORWARD, 75); m.motor(4, FORWARD, 75); delay(500); m.motor(1, RELEASE,1); m.motor(4, RELEASE,1); //RELESES THE MOTORS m.motor(2, RELEASE,1); m.motor(3, RELEASE,1); delay(500); m.motor(1, FORWARD, 100); m.motor(2, BACKWARD, 100); m.motor(3, BACKWARD, 100); //TURN LEFT m.motor(4, FORWARD, 100); delay(500); m.motor(1, RELEASE,1); m.motor(4, RELEASE,1); //RELESES THE MOTORS m.motor(2, RELEASE,1); m.motor(3, RELEASE,1); delay(500); m.motor(1, BACKWARD, 100); m.motor(2, FORWARD, 100); m.motor(3, BACKWARD, 100); m.motor(4, FORWARD, 100); delay(500); m.motor(1, RELEASE,1); m.motor(4, RELEASE,1); //RELESES THE MOTORS m.motor(2, RELEASE,1); m.motor(3, RELEASE,1); delay(500); m.motor(1, FORWARD, 100); m.motor(2, BACKWARD, 100); m.motor(3, FORWARD, 100); m.motor(4, BACKWARD, 100); delay(500); m.motor(1, RELEASE,1); m.motor(4, RELEASE,1); //RELESES THE MOTORS m.motor(2, RELEASE,1); m.motor(3, RELEASE,1); delay(500); }

• 
  @rosgr637 ай бұрын

  Thanks for your reply I totally agree with you I ordered the FNB58 so I will see what happens I have seen your other videos and thoroughly enjoyed them Than you for your time and effort

• 
  @tonysfun7 ай бұрын

  Thank you very much!

• 
  @rosgr637 ай бұрын

  Thanks for the great review! Can the FNIRSI FNB58 use, identify and test Thunderbolt 3 and Thunderbolt 4 cables? Thank you!

• 
  @tonysfun7 ай бұрын

  No, it is strictly USB tester only, sorry. I searched Amazon for tester for your cables, but there isn't any tester for your needs. But in very short time, the apple products will have USB-C ports, so you will be able to buy a tester or two like the rest of the world! Personally I think there should be one cable and one charger for customers, so there is less waste and makes the devices compatible, again it is great for customers! Have you seen my other video that also test USB cables? kzread.info/dash/bejne/Zp6ZubaOfKbRiaQ.html&ab_channel=TonyFleming I searched for an a adapter for your cables, but couldn't find any that I can recommend.

• 
  @antonioscarcella47107 ай бұрын

  Grazie per il video, però non hai fatto vedere come si calibra.

• 
  @tonysfun7 ай бұрын

  Please read bellow: I have tested the tester with 3-pin-shorted-out, provided with the kit, but it doesn't do the self-test either. In the SETUP you can turn AUTO-OFF or turn TEST mode at the startup - that's about it. I think it does the calibration internally during the bootup-sequence, so no need to calibrate.

• 
  @akramdogha37787 ай бұрын

  i have enjoyed it thank you for this nice video.

• 
  @tonysfun7 ай бұрын

  That is why I do these videos! Glad to see you enjoying them! have a great day!

• 
  @akramdogha37787 ай бұрын

  @@tonysfun thank you, you too have a good day and keep making videos.

• 
  @moparnut62867 ай бұрын

  Nice!

• 
  @natesgarage7 ай бұрын

  Nice and simple - very cool!

• 
  @SergeKmit7 ай бұрын

  Useless review. No information on components and microcontroller.

• 
  @nikkisixx2878Ай бұрын

  Not only that, but the author also refuses to correct his mistake! This is disrespect for your viewers.

• 
  @user-nj2zm8wc9z7 ай бұрын

  ❤❤❤❤❤👏👏👏👏👏

• 
  @tonysfun7 ай бұрын

  Glad you like it. Did you see the second car that is also voice controlled? BUT it does not need a phone to operate.

• 
  @user-nj2zm8wc9z7 ай бұрын

  @@tonysfun Yes, I watched the video. Great work. We will benefit from it in the robot competition because we are looking for ideas to design our own model. We thank you for your efforts.