Пікірлер

• 
  @car_detailing032710 күн бұрын

  I have an old Ruger 1022, it was pretty neat and the metal was all worn, I cleaned it up good and tried some cold blue, just to try and make it look better, after multiple coats, and light steel wool in between it just wasn’t turning black and just looked bad, no matter what I did, so I decided to do some spray paint, sounds weird but just wanted to know if that’s normal for old guns like that to not accept blue good

• 
  @WildMountainGarage7 күн бұрын

  I'm not an expert on blueing but metal is porous to some degree and perhaps there's decades of oil buildup. Maybe hot bluing would work better. If it's not a super nice gun ain't nothing wrong with a rattle can paint job. If it is nice, maybe cerakote/duracoat will be an option.

• 
  @mediocreman210 күн бұрын

  So you didn't change the timing belt or the valley pan gasket. How old is the timing belt? Or how many miles? If you're planning on changing the timing belt on these, it's probably the easiest V6 timing belt job there is. You literally don't need any special tools. Just pull the crankshaft pulley off instead of taking off the crankshaft pulley bolt. Just be careful not to strip out the hex bolts.You don't even need cam holding tools as long as you mark the position and don't move them. Be sure to slap in a new Audi thermostat and belt tensioner and pulley, and do a quick pressure test to make sure the heater hoses under the cowl aren't leaking. Probably the previous owner saw some coolant needing replacing and decided it was the head gasket without doing any actual tests.

• 
  @WildMountainGarage7 күн бұрын

  Great info. It was low on compression so I just reassembled and sold to an Audi enthusiast who's putting a different engine in. Needed some cash. Sad to see it go.

• 
  @mediocreman210 күн бұрын

  I'm confused why you would pull the engine without checking the valley pan gasket. 99% of the time that's where oil leaks are coming from. I'd recommend getting on the Quattro World forums so you don't have to do so much extra work.

• 
  @mediocreman210 күн бұрын

  The wood is real. The rear antenna is the radio antenna and telephone antenna, not just telephone antenna. Why would you call it a German piece of junk when it has 330,000 miles (Most likely on the original engine and transmission), and is in great shape and is only $600?

• 
  @CoreyWard-y2o21 күн бұрын

  Hey bud, great video! looking for a model number for the RC control arms you put on?? What size lift do you have?

• 
  @WildMountainGarage20 күн бұрын

  Thanks. I don't see the same arms on the rc site anymore, I'm only seeing arms for a 3-4 inch lift. Maybe a distributor still has them. They're for a 2" lift/level, which is what I have with different keys.

• 
  @barrymitchell442422 күн бұрын

  Soft toppers ?

• 
  @WildMountainGarage20 күн бұрын

  Soft topper is the company that makes the canvas top. It's awesome.

• 
  @michaelthompson757029 күн бұрын

  Think the same happened with my 1895 45-70,,,,,,,thanks for the discovery……

• 
  @MrTubeman123456Ай бұрын

  Mine has no buttons on the dash to push

• 
  @MadxGSxАй бұрын

  Hell yeah man. My 2019 l5p is lowered 2 inches with 22x12s. Been nervous as all hell to do a norcal myself, but you convinced me! Badass video man. Thank you.

• 
  @WildMountainGarageАй бұрын

  Lowered! Definitely need the room..with a little more patience than me it'd turn out mint

• 
  @kidburnz4891Ай бұрын

  Mine tends to fall out or become loose when I am shooting, fits snug but the kickback from the Glock g43x tends to make it wiggle out or become loose a little bit Any tips on how to make it stay better ?

• 
  @WildMountainGarageАй бұрын

  Oh man. Mine don't have any issue. Sounds like there are some tolerance issues. Maybe a little hot glue so it stays but isn't permanent but I hate the sound of that. Not much you can do to make it tighter without adding material to the frame or plug

• 
  @kidburnz4891Ай бұрын

  @@WildMountainGarage true thank you

• 
  @svd9299Ай бұрын

  I use a boat hook instead of a broom :)

• 
  @StephenRicketАй бұрын

  All owners with this error need to file a complaint against Chevy for the MANUFACTURERS DEFECT because the defective coolant reservoir tank causes this issue by not permitting the top of the tank to flow down to the bottom of the tank where the sensor is.

• 
  @WildMountainGarageАй бұрын

  100% recall worthy. Took me adding coolant into the return line port to fill it to get the new one to stop complaining.

• 
  @StephenRicketАй бұрын

  @@WildMountainGarage I used a long, thin drill bit to core a hole from the top to the bottom tank. While it now drains from the top to the bottom tank and SHAZAM the coolant flowed from the top to the bottom of the tank where the sensor is. MANUFACTURER DEFECT 100%! Chevy wanted $675 (just for the tank and sensor) to resolve their DEFECTIVE.

• 
  @marsbougie13 күн бұрын

  You didn't even know about filling up the bottom of the tank?

• 
  @StephenRicket13 күн бұрын

  @@marsbougie Even after filling the bottom tank fluid that enters the overflow will NOT return to the lower tank.

• 
  @myopinion4567Ай бұрын

  “Plastic stackable bin” at Lowe’s for $20 each. 2 of them will EXACTLY fit across the back of the bed by the tailgate. Just hook’em together and to the walls…put all your groceries/stuff securely in them. I love mine! You’re welcome!

• 
  @Nobody-cd4oxАй бұрын

  Terrible camera angle. You can't see what he does. Did he even watch this before he posted it? All you see is his hand.

• 
  @donaldminor8207Ай бұрын

  Home Depot sells plastic trays. Talk in the back , short in the front. About 4 yrs ago $15. Two fit almost perfectly in my 2020 F150. I use a cargo ratchet bar to hold them in place.

• 
  @JohnDoe_88Ай бұрын

  Impressive tear down! I still have my 1995 a6 still driving. Family car bought locally in 97. I love this car!

• 
  @SilvgvАй бұрын

  Good review. Thanks for posting. Did you ever wear the boots during 100 F+ weather? If yes, did your feet overheat?

• 
  @WildMountainGarageАй бұрын

  Yes, it gets that hot here in the summer. Yes, my feet got hot working or hiking. Definitely hotter with a lot of footwork. But for boots they seemed great. I wouldn't be surprised if there was a specifically better boot for that kind of heat. Definitely prefer sandals in 100+ lol

• 
  @jamesh96782 ай бұрын

  Thx for not using power tools, need to go replace my sons control arm out in the sticks and I’m an old school air tool guy. Hand tools only, looks like np, hopefully anyway🤣

• 
  @WildMountainGarage2 ай бұрын

  Totally do-able, hopefully he's not in the rust belt lol

• 
  @TylerBaker-su7hn2 ай бұрын

  You find a def fluid relocation let me know. Nobody makes them

• 
  @hansimuller74942 ай бұрын

  Audi never build better cars between the late 80`s and mid90`s. I had a Audi 80 and a 100 during that time. Never had such good and solid cars ever since. The rust prevention is the best, even 25, 30 years or oder older cars are usually almost rostfree if they have been treaten with a minimum of care.

• 
  @deaconpatterson90502 ай бұрын

  The wiring harness that you used to tap into the tail lights, (not the trailer connection) was that provided with the bar or did you purchase separately?

• 
  @WildMountainGarage2 ай бұрын

  The bar has a 4 pin connector

• 
  @WildMountainGarage2 ай бұрын

  *4 pin connector at the end of a few feet of wire

• 
  @MAC-gx3ji2 ай бұрын

  I replaced the cap clamp bolts with eyebolts They came in handy more than once

• 
  @nathanclaytor40832 ай бұрын

  Just came across this post and you have a great truck. I will always have an eight foot bed on my truck. One way to beef up a net is to lace some 3 strand line through it to take up the stretch, do it horizontal and vertical if necessary. An extendable boat hook is also handy for retrieving items in the bed. I remember when trucks came standard with eight foot beds, boy time is flying. Good post.Thanks!👍⚡️

• 
  @sag1122812 ай бұрын

  Thank you so much!!!! Worked like a charm!!!!

• 
  @rolo57822 ай бұрын

  Thanks for telling me how you got it out.... not....

• 
  @arturapozyan482 ай бұрын

  она вся в жиру! кватро, акпп , климат, люк, ещё и 7местная! у меня А6С4 2.8 авант кватро с механикой и климатом

• 
  @rhinomite52032 ай бұрын

  For what the trucks cost should already have imo 😂😂😂

• 
  @LincolnHawk-bk5yr2 ай бұрын

  For what trucks cost today, they should come with someone to load your lumber and groceries and help you with a run to the dump.

• 
  @rhinomite52032 ай бұрын

  1000% 😤😤😤😤

• 
  @Redeemedpooper2 ай бұрын

  You need a flash light your gun isn’t a flash light

• 
  @WildMountainGarageАй бұрын

  I have multiple but keep in the truck and around only in my pockets at night.

• 
  @Sithlord2042 ай бұрын

  Great job……

• 
  @Sithlord2042 ай бұрын

  Things not easygoing…. You did good it might smooth out by it’s self

• 
  @WildMountainGarage2 ай бұрын

  Actually ended up being passable enough until we sold it last year. Definitely could have been better but I basically forgot it was done.

• 
  @MrDoctour2 ай бұрын

  Shoulda got the black one

• 
  @WildMountainGarage2 ай бұрын

  Nah tan looks great and doesn't show dirt

• 
  @nastysoda92123 ай бұрын

  good job, you repalced very high quality american made aprts with bottom of the barrel chinese trash

• 
  @WildMountainGarage2 ай бұрын

  Lol they're fine and still going strong

• 
  @WildMountainGarage3 ай бұрын

  I've had the dreaded "COOLANT LEVEL LOW" message intermittently despite having full coolant. The sensor is molded into the tank so the whole tank must be replaced. Dorman 603-009 Engine Coolant Reservoir amzn.to/4aWvGP8 GM Compatible Orange Coolant amzn.to/4bgp0v4 Battery Terminal Brush amzn.to/3WmxEUv Autel Maxisys Scanners amzn.to/3UkzToK *As an Amazon Associate I earn from qualifying purchases.*

• 
  @stevesmith94033 ай бұрын

  I just used the trusty 2X6 across the back. It was on hand. I added a couple of D rings to it for tie down.

• 
  @f5fstop3 ай бұрын

  Broom is an old item, many use a broom.

• 
  @WildMountainGarage2 ай бұрын

  Been serving society for hundreds of years

• 
  @daviddavis36193 ай бұрын

  Hey great video. How about a update. Did they hold up

• 
  @WildMountainGarage3 ай бұрын

  Thanks! Yes, still going strong

• 
  @daviddavis36193 ай бұрын

  @@WildMountainGarage awesome I just put a set on a 1500 silverado. Thanks man

• 
  @cuocsongkentucky99513 ай бұрын

  Hi there, thank for your video, I have 2006 Cadillac DTS, One sensor left front bad, I bought new one from Autozone, some how they didn’t work, do I have to buy from dealer? Please let me know, thank you

• 
  @WildMountainGarage3 ай бұрын

  I'd buy off of Amazon or ebay or rock auto. Autozone will overcharge you. Dealer will rip you off. If still doesn't work try a local shop that won't rip you off.

• 
  @mr.sept.57903 ай бұрын

  Is anti cease on threads ok?

• 
  @WildMountainGarage3 ай бұрын

  Never had an issue. May affect torque values but being from the northeast originally everything rusted so if you wanted to get it apart antiseize was a must. Up to you though.

• 
  @patrickmaheux88073 ай бұрын

  When installed and rolling on dirt road, do they protect the paint well? 4:53

• 
  @WildMountainGarage3 ай бұрын

  I've noticed a lot less being kicked up on the sides of the van so I'd say they're working. Nothing will stop everything though.

• 
  @everesth27513 ай бұрын

  I want to get my center console out of my 2021 rebel 1500 and replace it with a jump seat as well is does this video apply.for those models

• 
  @WildMountainGarage3 ай бұрын

  Vehicles change over time but usually a lot less than you'd think. I don't think it'll be exact, but most of the concepts should be similar. You'll want to watch out for any modern electronics that may make it more involved.

• 
  @Catholic13914 ай бұрын

  I programmed two more of mine over a year ago and it works fine, then put it away, today I tried them, none of them work? I dropped the original one and lost the battery, so I took the battery off the one I programmed a year ago to my old remote just to lock my vehicle. So why did the memory program one forget its memory?

• 
  @WildMountainGarage3 ай бұрын

  Odd. Not sure. Sounds like you'll have to program again.

• 
  @Gsantos224 ай бұрын

  Am I tripping or were your tie rod ends installed upside down on the knuckle ??

• 
  @WildMountainGarage3 ай бұрын

  I put them on the same way the OEM ones were installed. It appears to be for clearance for the sway bar.

• 
  @TrueStrongNorth4 ай бұрын

  That's one of my favorite dashes of any car.

• 
  @bookish54344 ай бұрын

  I bought a 95 for $100 finishing touches are tires and struts all the way around and seal the top. 123k miles runs and drives.

• 
  @Division264 ай бұрын

  Did you bake it like the instructions call for?

• 
  @WildMountainGarage3 ай бұрын

  The barrel getting hot should suffice. Haven't had any issues since. But it doesn't have anything touching it so it hasn't scratched off.

• 
  @andyk20504 ай бұрын

  Fronts need triangular shaped extensions to atrach to doors. Will show in next few days when i make it.

• 
  @nancy49804 ай бұрын

  Thank you sir! I am trying this to reprogram the new fobs.

• 
  @temegsd73214 ай бұрын

  i have the same car for over 3 years now it was pain in the a at first i had a problem with the cylinder block that was cracked mixing water and oil it was hard fixing it but now its perfect oww btw u always have to bleed out air when adding new coolant

• 
  @chaddenton65394 ай бұрын

  Hi, how was it towing without side windows on the topper, visibility wise?

• 
  @WildMountainGarage4 ай бұрын

  It's fine. I've towed back and forth across the county and it didn't affect me. Tow mirrors are all I ever look at and side windows on the topper wouldn't add much, if any, visibility out the rear window. Plus, extra space to haul in the bed. Your rear view mirror visibility will be lesser as the rear zip in the window can get dirty and hard to see through, but again, tow mirrors are more than enough.

• 
  @chaddenton65394 ай бұрын

  @@WildMountainGarage Thanks for the feed back, super helpful!!

• 
  @caldwell50784 ай бұрын

  Grandpa beard guy says, Grandpa Topper hahahahaha

• 
  @johnnybravo29854 ай бұрын

  You didnt have to use the sleeves that comes with those RC a-arms?

• 
  @WildMountainGarage4 ай бұрын

  Arms just bolted in, there was nothing additional.