Robots Automation in the world Embedded system micro controller stm32cubeide
Robotics digitization innovation
hover board motherboard hack
Ultrasonic distance with Arduino
Arduino and Gyroscope GY 521
Ultrasonic Range finder
Servo motor
how to hack hover board motherboard processor speed control
BLDC motor hack
Innovations Use of micro controller processor
Arduino projects
Learn Arduino
STM32 ARM processor and uses in real life and industry
please subscribes
Arduino Industrial Automation
Arduino Sensors
Ultrasonic sensor
Arduino Tutorial
Pajero seat folding
Pajero 2nd row seat folding
Pick and place machine
Montero seat folding
Shogun seat folding
Robot Arm 6 Axes
Robot arm with Arduino
toyota Corolla Pajeero Honda Car self repair in Ghayathi Sanaya
Car Self repair in Ghayathi turn key on engine won't crank Toyota Atlas workshop Sinaya غياثي صناعية
Dining table Robot Maid
Hoverboard shaft repair
Hoverboard broken Excel C clamp Snap ring
Air wheel repair Hack Home made Robot
Пікірлер
I love your vidios❤
Thank you
Would you make an arduino controlled version too please?
Sure soon
Thank you very much, your tutorial helped me a lot 😊
Oxygen saturation (SpO2) is a measurement of how much oxygen your blood is carrying as a percentage of the maximum it could carry. For a healthy individual, the normal SpO2 should be between 96% to 99%
What is the point of the firmware? Why can a receiver just tell the circuit board to go forward and backwards?
Do you think we can use the motor controllers already existing on the hoverboard board? To bypass the hoverboard uC brain? Thanks.
Yes we can check my video hoverboard motherboard fitmware
hi, do you know how does pwm works on this controller? thanks
I will send you link
ZH X11A/B/S drives the motor with a series of On-OFf pulses it adjusts the duty cycle while keeping the frequency constant the speed output varies based on the speed demand input 4 which is speed input voltage 0 to+5 volts
How contact for more enhancement?
Depend upon controller you are using I use esp32 with bldc controller
Very good idea, thany
Mine gets stuck midway after washing process I think.any solution?
Я четыре года не мог сложить спасибо вам большое теперь смог сложить
Ryk mn koi is machine ka mechanic hai?
Kia problem hay jee
2X tilt sensors for each side can be mounted on top of eachother, cables lengthened and can be mounted anywhere on the Trike/Kart on a pivot and angle can be changed via regular throttle cable to tilt forward.... break cable can make tilt backwards for breaking or reverse... then no hacking will be needed to the board.
Have you seen that work well anytime?
That's an interesting idea. Diffently gonna try that :)
Great video. I had no idea until I saw the way you did it. Thanks for taking the time to help all of us 👍
Thanks full , 100% True.
Great video, thanks for sharing
Hey i want to ask you i did with remote but wheels always spinning when i turn on remote control but dont do enything only on what could be the problem? Pss: i have to remove and insert again battery to stop it and turn off remote. Thanks if you could help 😊
Use different hex file from github
@@embeddedmicrocontroller nice thanks but could you help how to turn left or right? back or forword it gose but left and right not😊
Does this work for the pinin 1.8 vivo swb version too?
Try this is general safety system to lock seat avoid folding seat while emergency break there is an other pull lock available for different vehicles
Steel tap can use this machine
سر جی
Hi
For the controller shown here, ZS-X11H 400W PWM 3 phase DC 6-60v, Please also show us the engine braking function, that is, how we can use it. We wish you good health, and we follow you with love. ❤❤❤
Sure
hello bro i need your help on hoverboard can you give me a contact address please
Sure
@@embeddedmicrocontroller I would be very grateful if you give me your contact address.
HI. I have one question. I have 40 volt battery and 400W 6-60V 16A BLDC 3 Phases DC Hall Brushless Motor Driver as you have in video. Can i use switch on battery power. it is not dangerous that i use 40V Battery using Switch? on-off 40v battery using switch it will be dangerous? i think it will be dangerous what you think? it will be more good that battery will be always on and red light on the board will be flashing the whole day? it is not dangerous that battery charging voltage also on the board switch? one time when i try just connect and disconnect 40V battery it had spark.
Use High amp switch
Chacha ji ye kitny ka hy cantrollar
What?
@@embeddedmicrocontroller cantrollar price?
Sir ji urdu min video banao banaoo
Ok
@@embeddedmicrocontroller sir ji ap apna nambar sand karny
Sir ji help me
Sir ji min pakistan sy hun ap ki awaz sy lag raha hy ap pakistani ho help me sir
Yes
@@embeddedmicrocontroller ap ki help chahy
Bhai jan ap pakistani ho
جی جناب
easy food student
kzread.info/dash/bejne/fJptvLVvlsuTetY.html
*PromoSM*
Can I just connect to a joystick?
Nice Display of high tech products..
Nice
Thanks
I have this model mashine his problem E9
Can you show the connections for the remote control to the motor controller?
Please I want to use it with rc remote control
Possible
One of your wires has 5volt on it. Is that coming from a 5 volt source? Like another battery? Or is the board itself suppling the 5 volt to that wire?
On board
How it is possible that a 36 volt 4AH battery, (which is only 144 watts/hr,) easily drives 2×250 watt=500 watts of Hoover board motors ? I need to know the logic,so please do reply,
This controller and bldc from same hover board friend
@@embeddedmicrocontroller that's my question brother, original battery supplies only 144 watts in total to controller, but motor requirements are 250 watt for each motor, for both motors 500 watts needed, then from where the extra watts being supplied to motors,
Motor doesn't sound healthy;/ are you sure those phases are connected correctly?
Inter Change the cables input Hall sensors or supply phases to motor both ways possible (position changing)
Tried everything but it isn’t moving! What should the next step be? Thank you
Move slowly you will hear soung tic/click and move seat downward it will fold
I didn't understand the switing part ?
Id you use one controller for the two motors ?
How you can make the 2 motors turn in same direction?
Possible
When one poteometer in middle both runs same direction
How i can get the inverse direction without using the reverse button ? I have two blcd motor and i want to theme turn in opposite of each other how i can doit?
Change the phase or hall sensors
This saved me tons! Thanks man! 😀
Hi, thank you for this excelente video. This controller have a brake funtion. Is possible use this funtion like regenerative brake system and load battery while wheel are braking??
this motor controler is suitable for e bike projects limit 350w blcd motors !?
Can a hoverboard that was using 14 cell, 24V battery use 20 cell, 36V battery?
Great tip
Glad it was helpful!