Пікірлер

• 
  @Tony-RS315 күн бұрын

  Would lt4 rods and piston work for lt1/l86 without lt4 crank, could the lt4 rotating assembly work in a lt1/l86?

• 
  @jjse7919 күн бұрын

  🤔

• 
  @stevenbean970626 күн бұрын

  i bought some solder sticks use the red one from the pack and solder sticked a 12ga wire to the two broken wires on my post so its now a wire not a small stud to connect ignition wire to

• 
  @stevenbean970626 күн бұрын

  the small post is whats wrong , people over tighten them then you go to take the nut off and it snaps inside nobody ever goes over that small post ! in the past 30-35 years ive had at least 20 or more that are over tight you go to loosen them they snap and spin freely and do zero after ! no power no click no nothing once it snaps its junk and no rebuild kit made fixes em it has to be completely replaced

• 
  @aidenhepworth8283Ай бұрын

  Whats your thoughts on it ? I've just ordered one mate

• 
  @codeyjohnson9896Ай бұрын

  Check my other video, so far everything is great

• 
  @justingrimes8293Ай бұрын

  Where does the fuel rail secure to?

• 
  @sirlayoАй бұрын

  I appreciate it 🫡

• 
  @MalosGarage2 ай бұрын

  The gen 1 rod does have a mark that faces the front.

• 
  @tylersgarage12 ай бұрын

  Great video.

• 
  @jonathangaska22823 ай бұрын

  I had a similiar problem on cylinder 8 with a piston issue so I'm trying to locate one piston for the set. My question is 1) since gen one and gen 2 weight different can I still use only one gen 2 piston or should I just use a gen 2 set (if I can get it) and 2) will gen 2 pistons work in a gen one block as long as orientation is correct? Haven't been able to find out any info on forums...so thanks!

• 
  @codeyjohnson98963 ай бұрын

  Yes bore is the same, this Gen 1 block with g2 pistons and rods on the g1 crank combo now has 1000+ miles on it in a blower car. Get a set of g2 pistons and rods they are stronger

• 
  @Smasher-Devourer2 ай бұрын

  Just replace them all with Gen 2 pistons so the other 7 don't continue being a failure point. Or at least just replace the rods themselves. Sell the old rods to recoup some of the money.

• 
  @gavingibson574625 күн бұрын

  ​@@Smasher-Devourer I thought gen 1 and 2 pistons were the same strength and only the rods were different?

• 
  @oldseavor4 ай бұрын

  I feel like you went too far😮

• 
  @EricRush5 ай бұрын

  What's going on when brakes work fine but pedal does not fully return. Brakes drag and brake lights stay on until I lift the pedal with my toe. If I lift it too hard, it pops the light switch out of its bracket.

• 
  @user-sy4zw7hv8s5 ай бұрын

  Do they make cams to sound like this ?

• 
  @ryanables45395 ай бұрын

  I need you as a mechanic bro

• 
  @kobehargest6 ай бұрын

  Hey man I was trying to reach out go you about the holley intake. I watched your video of you drilling the holes for the injectors. Do you think you could do it on mine? I'll pay of course. I'll have it shipped out to you

• 
  @codeyjohnson98964 ай бұрын

  Oh man it’s been a while since I did that lol

• 
  @codeyjohnson98964 ай бұрын

  Hit me up @jbengines on instagram

• 
  @kobehargest6 ай бұрын

  Hey man, if I sent you my intake would you be able to do the same for me? Will pay of course. Serious Inquiry

• 
  @b.s.mboostedsuspectmotors54416 ай бұрын

  Is this version jb or dbb?

• 
  @martinboland78737 ай бұрын

  That’s the wrong thermostat

• 
  @Megacatares7 ай бұрын

  Rod orientation matters when there is a chamfer on the crank shaft. Have the larger beveled part of the rod face that counterweight chamfer of the crank shaft and the reverse for the other rod on each side. Otherwise the rod will bind. If there is no chamfer on the crank shaft and the rods are not offset it doesn’t matter. I still set mine up that way because it is good practice. Tang orientation doesn’t matter.

• 
  @codeyjohnson98967 ай бұрын

  I always try to match the oem tang orientation

• 
  @automatedshenanigans82307 ай бұрын

  .062 thousandths wall thickness non concentric sleeves yikes

• 
  @howardmcadams38527 ай бұрын

  Thanks for Sharing this Information with us

• 
  @codeyjohnson98967 ай бұрын

  My pleasure

• 
  @sinisterblack99908 ай бұрын

  Hi I've a 2020 ss manual my question is do i have to worry about a check engine light? I think U mention something about that at the beginning of the video but i wanna make sure of it before i do the mod.

• 
  @LTXabdul8 ай бұрын

  I am planning to do the same thing, I was wondering how is your project coming along?

• 
  @codeyjohnson98967 ай бұрын

  Haven’t assembled anything being lazy 😂

• 
  @eltrompudo269 ай бұрын

  How do conect the lock and unlock feature?

• 
  @kole4119 ай бұрын

  Did you hook up the heater wiring and if so how? I have a cm900 unit.

• 
  @unconventionalcrosy5210 ай бұрын

  Mine is smeared with amour all by accident what can I do to get it out?

• 
  @eternalbeing3339 Жыл бұрын

  The old one in mine did not have the other gasket rings. Just the big one and it was stuck to the housing.

• 
  @ruben.espino1180 Жыл бұрын

  did you have an issue bolting up the hot side housing bolts ? mine are hitting

• 
  @theoneofone2992 Жыл бұрын

  Torque with an impact and check it out after that or w.e you wanna do after that??? Are you fkn kidding me retard??? I fkn hate you idiot mfs that do videos like this 🤡🤡🤡🤡🤡🖕🏽

• 
  @dalowks5546 Жыл бұрын

  amazing, muisc to my hears

• 
  @tuffy16 Жыл бұрын

  Maybe I missed it, what about the wait to start light?

• 
  @forrestcary Жыл бұрын

  Very helpful, years later! How’s it holding up? Still functioning?

• 
  @lr0479 Жыл бұрын

  Hey there ! Great video! Any idea what that beige sensor in front of the brake booster is called ? I need to replace mine and cant find it. Thanks

• 
  @lr0479 Жыл бұрын

  It’s visible at :39

• 
  @Wooley689 Жыл бұрын

  Sound waves messing with the camera is wild.

• 
  @falloutnerd4847 Жыл бұрын

  I’m rwd swapping my rsx to but I’m using a 350z transmission or s2000

• 
  @mrhyspeed8769 Жыл бұрын

  Turbo size?

• 
  @kervynwalcott4344 Жыл бұрын

  Im going to do this. Liking this idea. Just to be clear, I do not have to notch the timing cover rite?

• 
  @codeyjohnson98964 күн бұрын

  Nope

• 
  @stevemccullough893 Жыл бұрын

  I'm sure your neighbors hate you

• 
  @TheErms12345 Жыл бұрын

  Damn dude that truck is mint

• 
  @Blakehenry11 Жыл бұрын

  Great video, I did this to mod also. I actually took mine to a muffler shop because I wanted mine welded. Car definitely sounds more throaty, is there a power gain? I think there is some up top but not much. This was more me trying to get rid of something that was bugging me.

• 
  @twiceonsundays Жыл бұрын

  I looked at that and wondered why the pipes were crushed like that near the muffler. That and the useless secondary cats. Seems like GM was trying to keep the sound under a certain decibel or something in the Camaro. These things serve absolutely no purpose other than to restrict sound. The car does sound very loud in bone stock form, but we like it just a tad louder!

• 
  @themechanicman3865 Жыл бұрын

  buy a Cummins do not buy one from the auto parts store they do not come with the rubber or the seal and if you look at the actual Cummins genuine part thermostat it is heavier Duty and the ones you get it O'Reilly's AutoZone Etc stay with the Cummins parts for that Cummins engine

• 
  @mikea1266 Жыл бұрын

  Ordering one of these today. Thanks for the awareness.

• 
  @BRWfilms Жыл бұрын

  You can actually rebuild the starter it's self as well if needed

• 
  @DB22_2SS1LE Жыл бұрын

  I would like to know the same if there was any tone change in the sound?

• 
  @solidsnake6123 Жыл бұрын

  I just did mine last weekend, it increased the sound, and flow. Touring now sounds like Sport, and Sport has more volume. The car does seem a bit quicker, also the install wasn’t too bad.

• 
  @DB22_2SS1LE Жыл бұрын

  @@solidsnake6123 Thanks for the update. I'll be doing it during the off season for me just need to finish getting my truck straight first.

• 
  @DB22_2SS1LE Жыл бұрын

  @@solidsnake6123 1 last question do you still have the factory NPP?

• 
  @solidsnake6123 Жыл бұрын

  @@DB22_2SS1LE, yes, I kept my NPP, still works just fine.

• 
  @DB22_2SS1LE Жыл бұрын

  @@solidsnake6123 cool.......... I drive in touring mostly and sometimes adjust engine sound manually to sport but if I can get touring close to it I'll leave it set on auto adjustments.

• 
  @Bob-gn8ph Жыл бұрын

  Thanks

• 
  @Gmny1MOA2 жыл бұрын

  I had the dual in dual out version w true duals put on my 2019 z71 5.3 and I love it...I had straight cat back before and it sounded like garbage at idle now its deep and sounds incredible at idle...still loud plenty loud enough...just sounds amazing really the way mine is set up

• 
  @mopar2ya1652 жыл бұрын

  I have the same turbo and ifvyou put the gasket on the turbine inlet you'll see the casting needs to be ground/opened up a good bit to match the gasket. I also blended the bolt embossments to blend into the exhast flow better.

• 
  @wickedsatan12 жыл бұрын

  Whats frana?

• 
  @marcoslugo61682 жыл бұрын

  I changed my thermostat still temperature going up I have new water pump new hoses

• 
  @solidsnake61232 жыл бұрын

  Did you notice any sound or power increase?