Пікірлер

• 
  @mattdouglas6630Сағат бұрын

  Did you ever get to the bottom of the Range rover starting problem Edd?. We have the same problem with ours and have spent nearly £4k with landrover so far and they still haven't fixed the fault.

• 
  @DeborahBurnage2 сағат бұрын

  It does not help that Mike is a car dealer in my opinion pratt

• 
  @garynoble54644 сағат бұрын

  Nothing worse than a 'dirty ring'😢 😂😂

• 
  @carlosmcmahon6235 сағат бұрын

  Edd that is sad to hear as I used to watch this show because of you and your car fir the cars you worked on.

• 
  @IamKlaus00710 сағат бұрын

  When Brewer went to Overhaulin and met Chip Foose, Chips assessment of Brewer was dead accurate.

• 
  @marksaunders448717 сағат бұрын

  Why so fast

• 
  @malverned38218 сағат бұрын

  I would say (as a coded welder / been in the car trade since 1982 as a fabricator welder) that brazing at 450c is the lowest end of the spectrum, bronze welding / silver solder (non cad) or "silver brazing" use temps from 750 to near 1000 degrees C and the "not as strong" thing is entirely dependant on joint design / prep and the skill of the operator. Mig is particularly easy to get horribly wrong in many ways as you know / probably have seen yourself in your job. There is a reason say alloy steels (T45 etc.) are brazed / bronze welded in both cycle and especially motor cycle frames to as give a different effect when subjected to stress and accidents. Since the 90's for example I have TIG welded F1 suspension from 4130, it is then heat treated and double tempered, but in a shunt will shear wheras brazed structures often distort badly but stay in one piece. Loved the shows Ed and enjoyed loads of your hand work (Saab was good) and this is generally a good vid that is clear for folks, trust me there are horrors out there, and everyone and his dog are doing videos of all sorts, some very iffy. As someone who's job for decades was fixing the carnage, even on stuff like original genuine Cobras and Astons / all sorts I do tend to be wary when folks say "I can weld"

• 
  @marvingross815122 сағат бұрын

  Way cheaper to send to the crusher

• 
  @andreasdendrinos9404Күн бұрын

  I guess that this show will have the future of TOP GEAR.....

• 
  @dannork1240Күн бұрын

  Ospho works too So does “Klean Strip brand Concrete metal Prep” for less than half the cost Regular vinegar will work too but take a lot longer but be WAY cheaper

• 
  @forceone3242Күн бұрын

  Because you're boring 🤣

• 
  @jimbranch6115Күн бұрын

  I don't want to even count how many people have said this but ied was the only reason I watched Wheeler dealers and I never watched it after he left😮

• 
  @Gennettor-nc8kx2 күн бұрын

  Edd has not only, alas, left Wheeler Dealers but he also seems to have left the earth.....

• 
  @Alan-mi1lp2 күн бұрын

  Edd fixes were the reason I kept watching the show. I always thought Mike came across as a wrong un. 😂

• 
  @Chigleybus2 күн бұрын

  Brewer's still a good watch to be fair. He's got the charisma whatever you say about him. So I think the show still worked reasonably well without EC because of Brewer's personality. Unlike Top Gear, which was dead in the water once they ditched Clarkson, especially when May and Hammond followed him up the Amazon.

• 
  @dragon2knight2 күн бұрын

  It's like Top Gear all over again....some folks can't be replaced. Good luck to you on your new endeavors, I'll happily come along for the ride!

• 
  @user-zd8ec2ou9y2 күн бұрын

  I applaud you, cutting corners is not option, don't lower your standards for the bean counters

• 
  @karstenandersen32692 күн бұрын

  Greetings from a fan in denmark! Edd you where absolutly epic in the show! 😊😊😊 Helping us non mecanics to get a better understanding! Your calm approach and great knowledge! Will always have a true fanbase! Thank you so much for your big effort! And all the best on your future projects! I will tag along! ❤💪👍

• 
  @sianwarwick6332 күн бұрын

  Looking forward to those videos

• 
  @nsk143mКүн бұрын

  Better have a pair of binoculars or better yet a telescope ready as you need to look very far.

• 
  @mattiastark18462 күн бұрын

  🎉🎉🎉🎉 ahahahah incredibile,multi Edd scintillante ...👍👍👍👍

• 
  @stephenbull89623 күн бұрын

  The sad thing is that they now concentrate on the technical repair side of the show. Best of luck Edd.

• 
  @brentjarrett68293 күн бұрын

  Don’t watch the show when Levi’s is in it or American cars

• 
  @johnparr58793 күн бұрын

  What happens to the...... RUST...... on the internal, sections of the chassis.........???

• 
  @figjam51813 күн бұрын

  Typical Americans. Buy a good business and think they can do it better and cheaper.

• 
  @lepezz3 күн бұрын

  Hi Edd, so sad …😢

• 
  @philipgrice10263 күн бұрын

  Damn. Now I want a Scotch Egg, or two or three, for dinner. Along with some baked beans and chips (French Fries to the uneducated) of course. And a pint of Theakstons Old Peculiar. Oh, to be in England now my tummy's rumbling.

• 
  @mattiastark18463 күн бұрын

  Fantastic Edd and the Lost rust range Rover , incredibile ...it's start ... It's a miracle🎉🎉🎉... Wow this video with 4x4 Is fantastic Edd N1

• 
  @OnurTosun3 күн бұрын

• 
  @pjv767b53 күн бұрын

  I hope Englands remanufactured parts are better than ours in the USA. We have a 50/50 chance of the reman part working after a few days of the install.

• 
  @peterafoxy59053 күн бұрын

  First class, excellent video. Well done.

• 
  @kevinmott62053 күн бұрын

  I wont be watching it . The Yanks will £@ck it up 😢

• 
  @Buzdu224 күн бұрын

  Acid dip then send it to be galvanized, job done

• 
  @johncrawford69924 күн бұрын

  I missed this the first time ,Thank You for the video like them

• 
  @boots29264 күн бұрын

  quit watching when Ed quit. Not same show.

• 
  @mauricelevy90274 күн бұрын

  Surely some of the answer lies with "VELOCITY" who wanted to Americanise the programme. Just like the media mobs who are now running F1 and Motogp

• 
  @emirsandkc81934 күн бұрын

  Kanalı yeni keşfettim dmaxden geliyorum baya güzel kanal. Ayrıca altyazıyı kim yapıyor garip duruyor yanlışlık var gibi düzeltilirse hoş olur.

• 
  @deangaryjames4 күн бұрын

  Hope you are going to pump it full of cavity wax when its done?

• 
  @MB-wl2bm5 күн бұрын

  Edd is KING

• 
  @hittrewweuy75955 күн бұрын

  After Edd left I pretty much stopped watching that show , he was the only reason one watched that show

• 
  @petergiourelas37535 күн бұрын

  Because mike's a flog

• 
  @Nicholas-ok9no5 күн бұрын

  Shame the other bloke was ever involved!

• 
  @Coyote_be5 күн бұрын

  Jamais regardé un seul épisode. 😮

• 
  @dynamicsolutions9855 күн бұрын

  Hi Edd, having the same issues. Do you have a part number for those cables and control dial module for the T5. Thank you

• 
  @noeaguinaga40185 күн бұрын

  Why not drop cinderblocks in to add weight so that the liquid rises over top of chasis, or weights or other car parts that you need derusted.?

• 
  @projector71415 күн бұрын

  This is interesting.

• 
  @charleswelch2495 күн бұрын

  I'm glad you used the coper lines. That's a permanent fix because the car will rust away long before the line breaks again. Glad you didn't stop after Wheeler Dealers days. Wold be awesome for the old crew to get back together and make a car running again for fun. You are a great mechanic Edd

• 
  @oddities-whatnot5 күн бұрын

  Is this important ? Do I need to know ? Does it affect my life ? No.

• 
  @peterppoulsen63085 күн бұрын

  Great having You back, Edd!

• 
  @katrinusdevries68695 күн бұрын

  Never watched it anymore since Edd left

• 
  @Nefelisdiardi5 күн бұрын

  What would you expect the mastermind behind the world's fastest toilet would use to illustrate rust removal? Well, croissants and scotch eggs, of course, what else ?😁😁