Пікірлер

• 
  @jaxondakota70803 күн бұрын

  Hey nice video! Couple questions tho, would it be better to clean off built up oil on the valve cover after you take off ignition coil bracket? Also can you do this job without using trans assembly, what if you have nothing, just the gasket, would that be ok?

• 
  @donaldcoffer95584 күн бұрын

  Thank you for that video, he helped me a lot, fixed my problem AC and tach working now

• 
  @PaulD.Harvey4 күн бұрын

  You are right! What a mess. I had to rebuild my 350 and after having some trouble trying to get the engine to turn, I decided to find a demonstration about re-installing the rod caps. Thanks for the information. I bought my truck for a guy and 18 mons. earlier if was bought from a car dealer. Best guess the character at the car dealer rebuilt the engine. trying to make a buck, right? probably didn't match up everything as he should have done. He was in a hurry!

• 
  @Twin_Lakay5 күн бұрын

  Hi,is that a quick struts..thank you

• 
  @lucasornelas61136 күн бұрын

  thank you for the video i am having the same issue took it to a machine shop and guy told me caps are all mixed up

• 
  @brendacronk97468 күн бұрын

  Where to buy these wheels?

• 
  @mjmcomputers8 күн бұрын

  amzn.to/45WJm9r

• 
  @hale1j8 күн бұрын

  This video made my job easy. The extra tps you throw in make it easier for sure. Thanks dude

• 
  @hale1j8 күн бұрын

  Hardest part for me was putting the door panel back on and getting everything to line up correctly

• 
  @lg.10339 күн бұрын

  My question is ...the hoes adapters that conect to the low side and the hight side are they the same or do they change co.pared to the modern ones?

• 
  @vintage76vipergreenBeetle10 күн бұрын

  Looks good.

• 
  @CORVAIRWILD10 күн бұрын

  1st view

• 
  @bigizzysworld425311 күн бұрын

  If you take the wipers and top trim piece off, you don’t have to remove the intake or anything

• 
  @GDSFlyboy12 күн бұрын

  Good tips! Thanks

• 
  @eddieromero722215 күн бұрын

  I have a 4.3 V6 2000 gmc sierra , will this work?

• 
  @mjmcomputers8 күн бұрын

  No it won’t.

• 
  @eddieromero72228 күн бұрын

  @@mjmcomputers Okay thank you

• 
  @dpeck504915 күн бұрын

  Worked great Thanks!

• 
  @johnnyt287616 күн бұрын

  Can't see! Your hand is in the way. 🤦🏽‍♂️

• 
  @OsmanMahack-sb9er19 күн бұрын

  شكرأ من سوريا حلب اعمل في نظام سسبنشل سيرفيس بمرسيدس 34 سنه لماذا لم تغير جزء اخطر يوجد سيال تفرون ابيض صغار 2 داخل حلازون نصف

• 
  @heyhey571223 күн бұрын

  A very well put together and helpful video. The information on the shim was gold. Thank you 🙏

• 
  @wandajames623425 күн бұрын

  ouch- low volume on voice- high on music..... like the content tho.

• 
  @nlg06270126 күн бұрын

  How much more lift can I get by running the Comp cams 26918 springs and Comp cams 787-16 retainers? I have stock Vortec heads with a Comp Cams CL-262-4 Cam with 0.464/0.470 lift. What clearance can I get with out needing to machine the valve seats?

• 
  @jackhutchins827227 күн бұрын

  Wrong drain plug Dude, check your manual. The right drain plug is a lot easier to get to and it's metal!

• 
  @briankordas186127 күн бұрын

  DIDNT FIX IT ON MY 2011 Sienna 3.5L Still blinking light clutch doesn’t engage

• 
  @XerxesX.12 күн бұрын

  electrical

• 
  @nakedmongoose12328 күн бұрын

  🙏 thank you for your help

• 
  @pimpdaddysatan29 күн бұрын

  If the connector cant squeeze in to remove the old fuel filter.. grab a small hacksaw and cut the fuel filter off at the nipple/connector.. now with the fuel filter out of the way, those little tools will fit around the nipple and easily pop it out!! 👍💯

• 
  @wuudw2hollotyps703Ай бұрын

  Great video! Mair difference!

• 
  @Ziade_GarageАй бұрын

  This is a terrible video. Showed nothhing

• 
  @dennisperkins2686Ай бұрын

  you did not do your homework on the Equinox. 1. you can cancel the auto stop start problem by putting the gear shift in low and use the plus on top of the shifter to go through the six gears & leave it at 6th gear you can see the gear changes on the dashboard. you need to do this every time you start the car, put in low and use the plus on top of the knob take it up to 6th gear. THE CAR WILL SHIFT NORMALLY ONCE YOU SEE THE NUMBER 6 2. You need to use the info. screen to add more displays. I found it and added battery volts, coolant temp & oil pressure. City driving with pot holes it can be a little rough. She handles really well on the highways. My Equinox is a little over four years old now. mileage is 71,000. My service guys at the dealership say I take really good care of the Equinox. I have heated seats, wish I would have ordered the heated steering wheel. Living in the northeast can be pretty cold

• 
  @artemshkundin9647Ай бұрын

  If you don't mind could you give a link to the bushing tool you used on an upper arm?

• 
  @markb.1259Ай бұрын

  8:50- The washer that goes over that tensioner pulley mounting bolt is not flat. Wish you'd of covered that in a bit more detail. My guess is that the indented side of that washer should be installed with the indented side AWAY from the bolt head. Do you agree? Thank you.

• 
  @a_life_painted_with_colorАй бұрын

  I really appreciate your videos, I wish there was a video of these vacuum "solenoids" getting bench tested so I can see what you're doing with maybe an external power supply energizing them.

• 
  @mgj996999Ай бұрын

  Curious, what happens if you put a magnet on the sensor and don’t take it off all summer? Then when it gets cold out, remover the magnet and the heat works fine. Thoughts?

• 
  @mgj996999Ай бұрын

  Has anyone tried this?

• 
  @edtam268Ай бұрын

  Happen on 2013 Highlander after 10 yrs it gone bad (but also after sitting a lot during Covid) going to try small magnets on top of the original (hopefully no need to epoxy too

• 
  @LamentHatesYouАй бұрын

  Thank you worked perfectly and I had no idea what I was doing 🎉

• 
  @yohanathandowns9057Ай бұрын

  Fixed my issue. Just replaced AC compressor and other accesories, afyer vacuum and recharge i noticed the compressor made a grinding noise when i turned AC off. Added a shim and got it to spec, now quiet as a mouse. The installation instructions didnt say anything about shimming and the shims the compressor came with were the wrong size. Used a shim from the old one. Thanks a lot 🙏

• 
  @achap3604Ай бұрын

  Do u need to remove Freon?

• 
  @davechartmathАй бұрын

  Good job you have a lot of patience you explain everything very good thank you

• 
  @robertsprafke9376Ай бұрын

  Thanks!

• 
  @markb.1259Ай бұрын

  Where's your radiator fan? I have the 6.0L engine (Yukon) with a mechanical fan. Do you have an electric fan? THANK YOU for your video!!

• 
  @mjmcomputersАй бұрын

  I converted to electric fans.

• 
  @TheRealMyrmidonАй бұрын

  Thank you

• 
  @samb316Ай бұрын

  Thank you very much for posting. I have to make this repair on my own golden eagle!!

• 
  @shutupimcooking120Ай бұрын

  I performed the magnet test. It turned on but did not get cool

• 
  @renosgarage7451Ай бұрын

  My primer pump didn’t work so I just used starting fluid to make the motor run and pull a prime

• 
  @anthonynicholich9654Ай бұрын

  or 240D or 220 and 200 in Europe. Also 230E and 280.

• 
  @midlander3760Ай бұрын

  Thanks for the video. The Kawasaki FH601v on my Scag Tiger Cub started surging the last time I used it. I replaced the fuel filter and filling the hose from the pump to the carb with carb cleaner and ran that through the engine which didn't fix the issue (it's never that easy). I took my carb off and cleaned it after watching your vidwo as mine looked the same as yours on the outside and turned out to be the same on the inside as well. Only difference I noticed was it looks like your needle is metal whereas mine is plastic with a rubber tip. It was very helpful to see what to expect before tearing into it. I was able to reuse everything and I think the issue was something in one of the tiny holes on the carb as it initially had some resistance when trying to run a tiny piece of wire through it. I ran the wire through all holes followed by carb cleaner, put it back together, and it is running smoothly now. I think I could have ordered the same kit you did, if needed, based on what I saw in your video, or my nearby Scag dealer said the various o-rings were available individually just not as a kit (at least not for my exact engine). I before pulling the carb, I also tried starting the engine with the hose from the fuel pump to the carb off to verify the pump was working. I was surprised to see some debris in the fuel from the pump. I let the pump run a little to clear off of that out (this was after I replaced the fuel filter). I cut open the old filter since I couldn't see inside of it well, and found the side of the element going to the carb loose. I may have broke it loose cutting it apart but seeing the debris that that came out of the pump makes me think it was loose inside and maybe what cause my issue to start with by letting something get inside of the carb. Anyway, thanks again for the video.

• 
  @glenngrabs4310Ай бұрын

  This is about the worst filming. The camera was on the system in the motor bay for about 3 seconds. I saw more of the truck grill than anything else

• 
  @bassNvocalsАй бұрын

  Please don't fault me for this, but I kinda like seeing you struggle, fail, adjust your approach, try again, and eventually succeed. It's very similar to just about all my DIY projects, and I find it strangely encouraging, super informative, and even entertaining. I don't even care about the length of the video. You can always watch it in segments or repeat. Yeah, good stuff! Thanks!

• 
  @ericacruz1495Ай бұрын

  How long does this normally take?

• 
  @NUTTYEV08Ай бұрын

  So like I know this is 4 years later but I need help my quad the two lights on the right red and yellow don’t turn on at all but the batter is nothing wrong with it I I need help pls

• 
  @michaelgrijalva8479Ай бұрын

  You make this sh... Look easy,

• 
  @johnloutzenhiser7032Ай бұрын

  Nice workes well thank u.

• 
  @ek6667Ай бұрын

  Hi I have 93 s600 with 722.3, it dose flares when shifting I believe 3-4 thanks for your help in advance, I have changed the oil twice and filter