Saving and sharing this video 4 sure. Thank you, sir.
@douglasdinh6807Ай бұрын
This is basic ass math
@matthewd6306Ай бұрын
Thats a solid quick way to get your OD Radius to make your cut. But it doesn't get your the Center to End dimension. If you use the formula in the Blue Book you can get the Exact Outside and Inside radius cut marks. We laid out a flanged Elbow that had a leak in it. It was originally a field fit with slip ons and a mitered 60° Ell. We measured the existing piece, Angle(60°), C to Face of Each flange, and the flange rolls. Did the math in the office and came up with your Mitered cut dimensions and new Center to End dimensions. It also had a 10° flange roll on the bottom(vertical run) flange that was tricky to get the angle on. We ended up needing to take 1/4" off 1 flange and 1/2" off the other. Fit it up, welded it out and it fit perfeclty. No field fit Slip Ons required. Not sure how many Pipefitters would have been able to figure that out, sketch it, fab it and make it fit first try. Only been a fitter for 4yrs but learned from some Layout guys that are absolute Wizards. Rolling offsets? no problem. Mitered Ells? No problem? Rolled Flanges on a vertical run? np. Rolled Lateral Tees? Tricky as Fuck but made it fit first try. Couldnt be more grateful to John and Jim the Pipefitter/Layout Wizards.
@stn71722 ай бұрын
What all size pipe you can use on that?
@benni854 ай бұрын
Is there another way to make sure the fitting is properly squared? With out an angle finder? My boss asked me to use a square to check my bevel on some 45s i made and i drew blanks.
@kochese755 ай бұрын
We’re installing this stuff now. Was recommended from a friend in the field. Well it sucks, I hate it. Done floors with cheaper crap that worked much better. Thanks for video.
@leonelgonzalez12656 ай бұрын
are you sure this is rigth buddy what your saying
@offthehookdesignandfabdotc25826 ай бұрын
Should be but you need to subtract the takeoffs for the elbows. This is 2 ways to double check so double check.
@MarineScoutSniper6 ай бұрын
You are putting it in backwards. Just saying
@offthehookdesignandfabdotc25826 ай бұрын
I know. I had to in this room. Wife wanted the living room done first. Certain places you have to go backwards like closets ect.
@MarineScoutSniper6 ай бұрын
@@offthehookdesignandfabdotc2582 I understand. No worries
@sanannnan6 ай бұрын
Thx for sharing. I used baby powder to get tiles to slide more easily.
@user-eo9jc6bn1d6 ай бұрын
I feel sorry for this guy
@RichGT350r6 ай бұрын
I have a quick question. Do you have any formal pipefitting training? Why do I ask.. I’m actually a teacher at our local union. Sometimes pipefitting channels come up on my feed and I have to have a look. Most I laugh at. I did come across a couple “Smart Azz” Guys about 15 years ago. I gave them a problem to work out and they still have yet to give me the correct answer. You have a genuine interest in pipefitting. Keep up the good work!
@offthehookdesignandfabdotc25826 ай бұрын
No formal training in pipe specific type work., just worked in fab for many decades and with some ace hands who I learned a bit from also. Worked with some great guys in precision sheet metal holding very tight tolerances through multiple bends and how to get the correct flat patterns for complex things like rectangle to round offset transitions. Had a little formal training with drawings and math as it applied to precision sheet metal but mostly just doing it a long time and trying to help out the other guys with layout.
@RichGT350r6 ай бұрын
@@offthehookdesignandfabdotc2582 That’s Great! Keep doing what your doing and never be afraid to learn new things! 🤙🤙😎. I spent my whole career as a pipefitter. 25 years in a paper mill and 15 years building engineering spaces in new cargo ships. Big boilers and SuperSized Superchargers. Did you ever see a supercharger with a 72” diameter inlet! 🤣🤣
@RichGT350r6 ай бұрын
You missed the takeout for the elbows.
@offthehookdesignandfabdotc25826 ай бұрын
If you listen to the beginning of the video I said this was for figuring out the center to center distance. The elbow take off will of course have to be subtracted. That is a given.
@RichGT350r6 ай бұрын
@@offthehookdesignandfabdotc2582 I missed that part. Loved the presentation! 👍👍. It was nice to see someone getting off the 45* kick. Pipefitting is not always 45’s, tees and 90’s.
@offthehookdesignandfabdotc25826 ай бұрын
@@RichGT350r true. I made some other videos for figuring out the take off and other things. Tried to keep it simple and separated.
@jeremyescobedo30792 ай бұрын
So would both fittings be a 42 degree?
@RichGT350r2 ай бұрын
Yes
@colejbennett7 ай бұрын
Great way of explaining!!! The box visual is perfect!!
@mopiping7 ай бұрын
FOR TO FIND RADIUS 45° OF 3" BUTTWELD 45° /2=22,5 TANGENT 22,5 =0,4142135424 TANGENT 22,5 X RADIUS 90° OF BUTTWELD OF 3" WHICH IS 114,3 MM 0,4142135424 X114,3 MM =THE RADIUS OF 45° EXACT IS 47,3446101823 FOR 50° _55°_60°........ ALWAYS DIVID IT BY 2 THEN THE TANGENT OF RESULT X 90°RADUIS TO FIND DEGREE TANG -1(OPPOSITE OF ANGELES /ADJUST THE ANGELS)=ANGEL
@dylanhenry88168 ай бұрын
Great explanation and teaching tools! Awesome video all around thank you!
@stuartd699 ай бұрын
Awesome video, thanks mate. The string technique is a brilliant one
@stevenmchenry92769 ай бұрын
Great job budd
@user-hh3df8nk2w10 ай бұрын
Can you please make a video of how to do a Mira join?
@user-hh3df8nk2w10 ай бұрын
Very easy to understand
@maxkonta628411 ай бұрын
The box example is the best way to show it works rooling offset calculation... THANK YOU FOR YOUR THIS GREAT VIDEO!
@dylanb653211 ай бұрын
Couldn’t you just do the same thing you did for the top of the 90 to the bottom and get a mark on the top and the bottom and just connect the two or no?
@offthehookdesignandfabdotc258211 ай бұрын
Yeah that works, but the string wrapped and pulled tight will go to the shortest distance around the elbow which is right where it would be on the bottom and will yield the same result. Not a bad idea to use that to double check it before you cut it. 👍🏻😊
@carlosgrimaldo9622 Жыл бұрын
Amazing knowledge sharing Sr easy, clear and just to the point. Thank you so much
@ascii2795 Жыл бұрын
I know this video is two years old, but you saved my sanity. I'm using wax on EVERY piece and it's working beautifully. Thank you so much!!!
@victorbandibas3404 Жыл бұрын
Who is the autor of pipe fitter book ?
@sanjaysharmagazipuri9251 Жыл бұрын
𝙊𝙛𝙛𝙨𝙚𝙩. 𝙎𝙞𝙩×𝙧𝙪𝙣.𝙠𝙞𝙩𝙣𝙖.𝙝𝙖𝙞.𝙨𝙞𝙧.
@jaymezarbizu6731 Жыл бұрын
If you have a 45 instead of a 90 would you just cross multiple then divide by 45 instead
@robertgalaviz1159 Жыл бұрын
Heck of a video explaining and demoing, what a salesman, heck I bought one and I don't even weld, 😂
@dwightstebner2345 Жыл бұрын
no counter weight?
@offthehookdesignandfabdotc2582 Жыл бұрын
I do have counterweights for sale. I do use them often but in this example it would not be needed.
@gyffjogofl7676 Жыл бұрын
That's a nice setup!
@mikereynolds3294 Жыл бұрын
dang, i was looking at installing the Smart Core Ultra because they had the design and color i like (blue ridge pine) and i can find that design and color in any other plank. Now you got me shied away from it because i have never done plank and don't need an extra hassle. And the stuff is not cheap at $4.00 a sq ft thought it was quality
@okiedoke6373 Жыл бұрын
I don't weld pipe but I like to watch out lay it out it's funny how all that goes back together I took an electrical course in prison of course it had conduit bending in it and that's what this reminds me of conduit bending I was fortunate enough to work as an electrician for 6 years on that unit because I can't get an electrical license I feel back on welding and that's just barely a living for me at least where I'm at they want to get all the Mexicans a chance all the white people get pushed to the bottom of the barrel least that's what it seems like I can't find no work for nothing
@okiedoke6373 Жыл бұрын
Where'd you go bro still out there
@offthehookdesignandfabdotc2582 Жыл бұрын
Yes just busy running a business, behind on orders and stressed out. No time to make videos lately .
@williamhusseyjr1143 Жыл бұрын
lol @Suicide hotline
@markmainse3387 Жыл бұрын
You can also go a²+b²+c²=rolling offset length² if you know all 3 initially
@devindann8627 Жыл бұрын
Thnks 4 the tips!!
@kouadioedgardngoran5256 Жыл бұрын
Bonjour monsieur je voudrais savoir si vous pouvez traduire votre vidéo en français car je m'intéresse à ce que vous faites
@reyfernandez2543 Жыл бұрын
It's good to see people like you who like to share their knowledge ,unlike structural welders who are dopes.
@jlerwin8055 Жыл бұрын
I've used 3 versions of click-lick type flooring, including this specific brand, and they are all a pain to install. The last install was my LAST install!
@milan2k11 Жыл бұрын
I went to Lowe's looking to purchase vinyl tiles... I was sold this stuff, the first cut I did I noticed there's wood (cheap fiber wood) and all the vinyl was is the top wearing course. I installed steinmaster luxury vinyl planks In the bathroom and those were true vinyl throughout. This is not true vinyl throughout. Not happy.
@Justintimemetal Жыл бұрын
Your videos have helped me so much
@stevenarandas7907 Жыл бұрын
How much does this weigh
@KeepitABuck50 Жыл бұрын
Good video. I would explain though that 8" would be your center to center, 4" is your vertical distance between the pipes and 6" is your face to face. Good refresher 👍
@olliecreativethoughts_bird9145 Жыл бұрын
Unleveled floors causing interlocking friction...I had that issue too..
@jamesbarton3165 Жыл бұрын
You need to read the instructions. And use a bridge on every section. It's easier to install the recommend way. Bridge tap .. and so on
@2Smart4Uapes Жыл бұрын
Well thats one way to do it
@Cheto702 Жыл бұрын
I thought the next step after you have the 7.211 was to multiply by 1.414 can help with my question
@offthehookdesignandfabdotc2582 Жыл бұрын
The 1.414 is a shortcut to finding the length of the long leg of a triangle but this short cut of 1.414 only works with right triangles with equal legs and 45 degree corners.
@Cheto702 Жыл бұрын
Thank you very much for answering
@clifflatshaw5105 Жыл бұрын
If you do multiply the 7.211 by 1.414 you will avoid having to use mitered fittings. It will work with 45s no problem. Think about it!
@derekmorgan4895 Жыл бұрын
The best one I've come across yet for cutting down angles cheers mate
@MrTonyPiscatelle Жыл бұрын
The directions that come with this stuff is absolutely no help at all. Your tips were pretty good
@anim8ted923 Жыл бұрын
You seem very frustrated in the video. Now that it's done (I assume) what do you think of your LVP floor?
Пікірлер
Saving and sharing this video 4 sure. Thank you, sir.
This is basic ass math
Thats a solid quick way to get your OD Radius to make your cut. But it doesn't get your the Center to End dimension. If you use the formula in the Blue Book you can get the Exact Outside and Inside radius cut marks. We laid out a flanged Elbow that had a leak in it. It was originally a field fit with slip ons and a mitered 60° Ell. We measured the existing piece, Angle(60°), C to Face of Each flange, and the flange rolls. Did the math in the office and came up with your Mitered cut dimensions and new Center to End dimensions. It also had a 10° flange roll on the bottom(vertical run) flange that was tricky to get the angle on. We ended up needing to take 1/4" off 1 flange and 1/2" off the other. Fit it up, welded it out and it fit perfeclty. No field fit Slip Ons required. Not sure how many Pipefitters would have been able to figure that out, sketch it, fab it and make it fit first try. Only been a fitter for 4yrs but learned from some Layout guys that are absolute Wizards. Rolling offsets? no problem. Mitered Ells? No problem? Rolled Flanges on a vertical run? np. Rolled Lateral Tees? Tricky as Fuck but made it fit first try. Couldnt be more grateful to John and Jim the Pipefitter/Layout Wizards.
What all size pipe you can use on that?
Is there another way to make sure the fitting is properly squared? With out an angle finder? My boss asked me to use a square to check my bevel on some 45s i made and i drew blanks.
We’re installing this stuff now. Was recommended from a friend in the field. Well it sucks, I hate it. Done floors with cheaper crap that worked much better. Thanks for video.
are you sure this is rigth buddy what your saying
Should be but you need to subtract the takeoffs for the elbows. This is 2 ways to double check so double check.
You are putting it in backwards. Just saying
I know. I had to in this room. Wife wanted the living room done first. Certain places you have to go backwards like closets ect.
@@offthehookdesignandfabdotc2582 I understand. No worries
Thx for sharing. I used baby powder to get tiles to slide more easily.
I feel sorry for this guy
I have a quick question. Do you have any formal pipefitting training? Why do I ask.. I’m actually a teacher at our local union. Sometimes pipefitting channels come up on my feed and I have to have a look. Most I laugh at. I did come across a couple “Smart Azz” Guys about 15 years ago. I gave them a problem to work out and they still have yet to give me the correct answer. You have a genuine interest in pipefitting. Keep up the good work!
No formal training in pipe specific type work., just worked in fab for many decades and with some ace hands who I learned a bit from also. Worked with some great guys in precision sheet metal holding very tight tolerances through multiple bends and how to get the correct flat patterns for complex things like rectangle to round offset transitions. Had a little formal training with drawings and math as it applied to precision sheet metal but mostly just doing it a long time and trying to help out the other guys with layout.
@@offthehookdesignandfabdotc2582 That’s Great! Keep doing what your doing and never be afraid to learn new things! 🤙🤙😎. I spent my whole career as a pipefitter. 25 years in a paper mill and 15 years building engineering spaces in new cargo ships. Big boilers and SuperSized Superchargers. Did you ever see a supercharger with a 72” diameter inlet! 🤣🤣
You missed the takeout for the elbows.
If you listen to the beginning of the video I said this was for figuring out the center to center distance. The elbow take off will of course have to be subtracted. That is a given.
@@offthehookdesignandfabdotc2582 I missed that part. Loved the presentation! 👍👍. It was nice to see someone getting off the 45* kick. Pipefitting is not always 45’s, tees and 90’s.
@@RichGT350r true. I made some other videos for figuring out the take off and other things. Tried to keep it simple and separated.
So would both fittings be a 42 degree?
Yes
Great way of explaining!!! The box visual is perfect!!
FOR TO FIND RADIUS 45° OF 3" BUTTWELD 45° /2=22,5 TANGENT 22,5 =0,4142135424 TANGENT 22,5 X RADIUS 90° OF BUTTWELD OF 3" WHICH IS 114,3 MM 0,4142135424 X114,3 MM =THE RADIUS OF 45° EXACT IS 47,3446101823 FOR 50° _55°_60°........ ALWAYS DIVID IT BY 2 THEN THE TANGENT OF RESULT X 90°RADUIS TO FIND DEGREE TANG -1(OPPOSITE OF ANGELES /ADJUST THE ANGELS)=ANGEL
Great explanation and teaching tools! Awesome video all around thank you!
Awesome video, thanks mate. The string technique is a brilliant one
Great job budd
Can you please make a video of how to do a Mira join?
Very easy to understand
The box example is the best way to show it works rooling offset calculation... THANK YOU FOR YOUR THIS GREAT VIDEO!
Couldn’t you just do the same thing you did for the top of the 90 to the bottom and get a mark on the top and the bottom and just connect the two or no?
Yeah that works, but the string wrapped and pulled tight will go to the shortest distance around the elbow which is right where it would be on the bottom and will yield the same result. Not a bad idea to use that to double check it before you cut it. 👍🏻😊
Amazing knowledge sharing Sr easy, clear and just to the point. Thank you so much
I know this video is two years old, but you saved my sanity. I'm using wax on EVERY piece and it's working beautifully. Thank you so much!!!
Who is the autor of pipe fitter book ?
𝙊𝙛𝙛𝙨𝙚𝙩. 𝙎𝙞𝙩×𝙧𝙪𝙣.𝙠𝙞𝙩𝙣𝙖.𝙝𝙖𝙞.𝙨𝙞𝙧.
If you have a 45 instead of a 90 would you just cross multiple then divide by 45 instead
Heck of a video explaining and demoing, what a salesman, heck I bought one and I don't even weld, 😂
no counter weight?
I do have counterweights for sale. I do use them often but in this example it would not be needed.
That's a nice setup!
dang, i was looking at installing the Smart Core Ultra because they had the design and color i like (blue ridge pine) and i can find that design and color in any other plank. Now you got me shied away from it because i have never done plank and don't need an extra hassle. And the stuff is not cheap at $4.00 a sq ft thought it was quality
I don't weld pipe but I like to watch out lay it out it's funny how all that goes back together I took an electrical course in prison of course it had conduit bending in it and that's what this reminds me of conduit bending I was fortunate enough to work as an electrician for 6 years on that unit because I can't get an electrical license I feel back on welding and that's just barely a living for me at least where I'm at they want to get all the Mexicans a chance all the white people get pushed to the bottom of the barrel least that's what it seems like I can't find no work for nothing
Where'd you go bro still out there
Yes just busy running a business, behind on orders and stressed out. No time to make videos lately .
lol @Suicide hotline
You can also go a²+b²+c²=rolling offset length² if you know all 3 initially
Thnks 4 the tips!!
Bonjour monsieur je voudrais savoir si vous pouvez traduire votre vidéo en français car je m'intéresse à ce que vous faites
It's good to see people like you who like to share their knowledge ,unlike structural welders who are dopes.
I've used 3 versions of click-lick type flooring, including this specific brand, and they are all a pain to install. The last install was my LAST install!
I went to Lowe's looking to purchase vinyl tiles... I was sold this stuff, the first cut I did I noticed there's wood (cheap fiber wood) and all the vinyl was is the top wearing course. I installed steinmaster luxury vinyl planks In the bathroom and those were true vinyl throughout. This is not true vinyl throughout. Not happy.
Your videos have helped me so much
How much does this weigh
Good video. I would explain though that 8" would be your center to center, 4" is your vertical distance between the pipes and 6" is your face to face. Good refresher 👍
Unleveled floors causing interlocking friction...I had that issue too..
You need to read the instructions. And use a bridge on every section. It's easier to install the recommend way. Bridge tap .. and so on
Well thats one way to do it
I thought the next step after you have the 7.211 was to multiply by 1.414 can help with my question
The 1.414 is a shortcut to finding the length of the long leg of a triangle but this short cut of 1.414 only works with right triangles with equal legs and 45 degree corners.
Thank you very much for answering
If you do multiply the 7.211 by 1.414 you will avoid having to use mitered fittings. It will work with 45s no problem. Think about it!
The best one I've come across yet for cutting down angles cheers mate
The directions that come with this stuff is absolutely no help at all. Your tips were pretty good
You seem very frustrated in the video. Now that it's done (I assume) what do you think of your LVP floor?
Its ok so far. Will see how long it lasts.
he has a lot to learn on this