Пікірлер

• 
  @supermassiveblckman2 сағат бұрын

  Very useful video (for more reasons) but, since it takes several skills in soldering + perfect soldering iron + perfect tin + perfect soldering iron temperature, tin suction pump (cleaner work) (so, absolutely not base tools as not base skills) to do all this, instead of replacing the potentiometers, I recommend simply using dry cleaner electrical contact spray (perhaps the same one you used to clean the soldering iron) directly on the potentiometers and you will go on for years without replacing the potentiometers... then you will do it with base tools

• 
  @scenicroute69817 күн бұрын

  😊😍😊😍

• 
  @moisesrodriguez90238 күн бұрын

  Man you think you can teach me how to do all the soldering?

• 
  @SaifSKH10 күн бұрын

  Can you install a Hall Effect potentiometer instead of the regular one using this exact method ?? Like would the regular joystick work with a Hall Effect potentiometer or is the hardware different??

• 
  @don.timeless499311 күн бұрын

  methyl alcohol is preferred so it doesnt damage the car paint

• 
  @mohammad.sh11014 күн бұрын

  Good job 👏🏻🫡

• 
  @E.P.114 күн бұрын

  Awesome job! Once you broke out the soldering gun, my confidence dropped 😂. You make it easy.

• 
  @user-ny8nw8yl3u15 күн бұрын

  I have a novel idea,boycott Sony products until they put out a decent product .

• 
  @mohammad.sh11026 күн бұрын

  Good job 👌😀

• 
  @DIYVidss26 күн бұрын

  Thanks 👏🏻🌟

• 
  @philippe539428 күн бұрын

  Blue on blue, black on black. And at the end, it's a bad exemple to plug a power strip withe earth on another one without earth!! The cable clamp clamps the wires, instead of the cable sheath! Etc........

• 
  @DIYVidss28 күн бұрын

  That’s right… thanks for your advice👏🏻👌🏻🌸

• 
  @nonsuch29 күн бұрын

  Why would you reverse the wires? Blue goes to blue, black goes to black. It doesn't get any simpler than that, yet... you did the opposite. Why?

• 
  @DIYVidss29 күн бұрын

  Thanks for your attention… It makes no difference don’t worry😁

• 
  @mddawson125 күн бұрын

  @@DIYVidss It is important as any fused device connected to that power board will be fused across the neutral wire rather than the active wire. If a fuse on the neutral side blows, and the building does not have ground fault protection devices, then current could still flow from the line to the ground. [Of course, if the fuse were on the line side, and it blows, current could flow between neutral and ground, but the voltages are much smaller] So, it would seem that a line side fuse offers more protection than a neutral side fuse.

• 
  @jankas64Ай бұрын

  i would say not to do that . the extened had 1mm2 in it and is only rated for that not for 1.5mm2 so there is a very big risk burning the block itself. not good.

• 
  @lesliegrace8360Ай бұрын

  China. Cheap. Combustible.

• 
  @DIYVidss29 күн бұрын

  Thanks for your advice 👏🏻👍🏻🌸

• 
  @johnranaghan947Ай бұрын

  unconsciously incompetent, a danger to himself and anyone copying him

• 
  @DIYVidssАй бұрын

  Thanks for your attention 👍🏻🌟👏🏻

• 
  @raiders7071Ай бұрын

  FIRE!!!!!!!!!

• 
  @DIYVidssАй бұрын

  👍🏻🌸

• 
  @MrTflarsenАй бұрын

  You are making so many mistakes in this video. Take it down before someone gets hurt!

• 
  @DIYVidssАй бұрын

  Thanks for your advice 👏🏻🌟

• 
  @stevechatzaАй бұрын

  Tampering with electrical equipment like this is unsafe. Consider buying a rewireable extension strip, or an extension strip without the cable so you can use whatever length you like.

• 
  @DIYVidssАй бұрын

  Yes. It’s a better idea… thanks 👏🏻🌸

• 
  @vangoghskyeАй бұрын

  Just take the little round thing out of the green thing and clean both things. Worked for me. I used rubbing alchohol and qtips.

• 
  @vangoghskyeАй бұрын

  And I pried it apart with a guitar pick.

• 
  @DIYVidssАй бұрын

  Yes… sometimes it works… thanks for your advice 👍🏻🌸

• 
  @zanussi_and_aeg_fanАй бұрын

  Better used eco drum clean... Still good job

• 
  @DIYVidssАй бұрын

  Thanks 👍🏻🌸

• 
  @SheZ91Ай бұрын

  It was quicker to buy new one

• 
  @DIYVidssАй бұрын

  Precisely 😁👍🏻

• 
  @DJDIRTYYELLAАй бұрын

  My stick gets physically stuck.. (pause) is this a fix for that?😂 for real tho?

• 
  @patttttttttАй бұрын

  We should never need to fix this. It's Sony that needs to fix it. Few of us aren't tech minded. Need to fork out for at least £35 to get it fix but aren't garrenteed either . I'm n uk

• 
  @DIYVidssАй бұрын

  Thanks for commenting 👍🏻👌🏻

• 
  @mohammad.sh110Ай бұрын

  Perfect 👌

• 
  @DIYVidssАй бұрын

  Thanks for your attention 💫

• 
  @zukesnukem1723Ай бұрын

  Which cable is the one you took out on 2:43? I accidentally ripped that one and need to look for a replacement online

• 
  @DIYVidssАй бұрын

  Two bottom side are two mics cables… both sides are triggers … up side is for touch pad.

• 
  @gaimsharc71762 ай бұрын

  This controller is an over-designed pos... to spend that much money for something so small to go wrong is a terrible customer service issue - the Xbox controller has the same issue, but accessing the components can be done in about 3 steps without the need to put the entire controller at risk

• 
  @DIYVidssАй бұрын

  Thanks for your advice 👍🏻🌸

• 
  @MrLukasbigfoot2 ай бұрын

  Looks like you gotta change the shock absorbers...I think the drum is bouncing a little too much.

• 
  @DIYVidssАй бұрын

  Yeah… I think after 40 years springs are weak.

• 
  @vapenojutsuxllx60872 ай бұрын

  Damn I thought he was a werewolf 😅😅

• 
  @TheDARKNESS80302 ай бұрын

  What temperature did you have it to desolder? I tried today and could not get it it to separate

• 
  @DIYVidss2 ай бұрын

  It’s 60w soldering iron … it doesn’t designate the temperature.

• 
  @josefpreyes2 ай бұрын

  ganda ng video, ganito kelangan natin sa Pinoy KZreadrs or content creators yun may matutunan ka, hindi puro pa cute at pa raffle

• 
  @DIYVidss2 ай бұрын

  ❤️🌸

• 
  @armenia19892 ай бұрын

  pls buy soldering iron and flux paste😂😂

• 
  @DIYVidss2 ай бұрын

  Thanks for your advice 😁🌟

• 
  @tylerbecker41472 ай бұрын

  I don't own a PS5 since I'm a Xbox player but opening a PS5 controller looks way more harder than opening a Xbox controller. This is why I prefer to not have a built in battery pack over either the choice of batteries or a interchangeable battery pack.

• 
  @DIYVidss2 ай бұрын

  Appreciate 🌟👍🏻

• 
  @didiekrudianto86302 ай бұрын

  The analog joystick is still the same as the previous version, it is easily damaged, with a more complicated machine board, it is even more difficult to replace it, for some reason Sony doesn't make the analog one easily removable, even though I hope it is replaced with a socket model

• 
  @DIYVidss2 ай бұрын

  Thanks for your attention 🌟

• 
  @yyyrrrr42212 ай бұрын

  Where I can find like your tools

• 
  @DIYVidss2 ай бұрын

  From amazon or ali express 😀😀

• 
  @onitacular2 ай бұрын

  The no flux is crazy 😳😳

• 
  @DIYVidss2 ай бұрын

  Thanks for attention 🌟🌸

• 
  @luisluciano39272 ай бұрын

  Wow great Video man, keep up the good work!👏🏽

• 
  @DIYVidss2 ай бұрын

  Thanks for your comment ❤️🌸

• 
  @Unsubscribethispls2 ай бұрын

  Damn.. next time I will buy duals. edge... freakin drifts...

• 
  @DIYVidss2 ай бұрын

  Thanks for your attention 👍🏻🌟

• 
  @rival20282 ай бұрын

  Im just gonna buy a new pad. 😅

• 
  @DIYVidss2 ай бұрын

  👍🏻😁

• 
  @lesterbruke81662 ай бұрын

  Use flux and a copper braid to remove any remaining solder from the contacts. Always use flux when soldering, wetting and surface tension. You can also check the resistance of the potentiometers before installation. And please, clean the soldering iron tip.

• 
  @DIYVidss2 ай бұрын

  Thanks for your advice 👍🏻🌸

• 
  @attilatarjanyi54022 ай бұрын

  Legit solution, horrible execution. If you do that you will definitely destroy one of the vias. The correct method would be either leave the green part on and just change the moving parts, or use solder wick or a solder sucker to remove the solder, in that way the pcb will not be damaged.

• 
  @DIYVidss2 ай бұрын

  Yes exactly 👍🏻🌟

• 
  @Chatooly2 ай бұрын

  good video 👍 😁😊 🇩🇴

• 
  @DIYVidss2 ай бұрын

  Thanks for participating ❤️🌸

• 
  @haythamalexander2 ай бұрын

  Good fucking lord the piece is hard to get to… if you don’t have the soldering tool, it is practically cheaper to buy a new controller 🤷🏼🤷🏼🤷🏼

• 
  @DIYVidss2 ай бұрын

  Thanks for your advice 🌟🌸

• 
  @danielm41362 ай бұрын

  I wanna do this but i’m so terrified of soldering. Especially when it comes down to the black and red wires.. the soldering of the pot looks fairly simple though

• 
  @DIYVidss2 ай бұрын

  Yes it could be hard for first time 😁

• 
  @danielm41362 ай бұрын

  @@DIYVidss Do you have instagram by any chance

• 
  @DIYVidss2 ай бұрын

  @@danielm4136 No. I don’t 😁

• 
  @Altnet892 ай бұрын

  I opend it took out both "discs" and replaced them with those from old dualshock 4.

• 
  @DIYVidss2 ай бұрын

  Yea … it works 👍🏻

• 
  @jerryfinger19672 ай бұрын

  Ok so I did all of this and my right analog stick instead of drifting to the left now it just goes straight up and doesn’t stop, I can move sideways but not up and down at all it just goes up 😩😭 someone help me please

• 
  @DIYVidss2 ай бұрын

  Change it again… unfortunately most sticks in shops are not work properly 😕

• 
  @DIYVidss2 ай бұрын

  Change it again… unfortunately most sticks in shops are not work properly 😕

• 
  @Belik0n27 күн бұрын

  Did you ever figure out the problem because I’m currently having this problem as well, and I need a solution

• 
  @mikegyver19673 ай бұрын

  With my friends, 4 controllers, over 1000 hours/years of play, and.....0 drift.

• 
  @DIYVidss2 ай бұрын

  👍🏻😁😁

• 
  @stolentext94363 ай бұрын

  My potentiometer is damaged, i cleaned it and it was a pretty good temporary fix. But i think ill order a solder tool and more potentiometers and joysticks. Soldering seems like a usefull skill to have.

• 
  @DIYVidss2 ай бұрын

  Yes exactly… 👍🏻🌟

• 
  @SETtheTONE.3 ай бұрын

  I replaced the sliders inside for my right joystick & it worked perfectly. This was the first video I watched on the drifting problem so I had to leave a comment.

• 
  @DIYVidss2 ай бұрын

  Thanks for your attention 🌸🌟

• 
  @user-kf9ws3zc9k3 ай бұрын

  ❤❤❤❤❤

• 
  @DIYVidss3 ай бұрын

  Thanks for your attention 🌸🌟❤️

• 
  @ajmj09683 ай бұрын

  The Japanese game controllers fall apart in a couple of months. xbox controllers last from generation to generation

• 
  @DIYVidss3 ай бұрын

  Yes exactly… ps5 controllers broken down after a few months 😕😕 specially their sticks.

• 
  @Badangselatan3 ай бұрын

  This required much patience that i dont have...so nah...if i have my ds5 broken,then i just send it for the guy who know how to fix it or i just buy the new one😂

• 
  @DIYVidss3 ай бұрын

  Thanks for participating 🌟❤️😁

• 
  @dhmhtrhsntekeles36703 ай бұрын

  Hello..You play DMZ call of duty with ps5 controller.. I can’t play the game show me the controller of Xbox buttons to play