you bought the wrong kit not saying it wont work but yesterdays tractor has the correct sleeve and seal kit part Item #: 173253 $52 plus shipping no jacking around and works. I own 3 2000 and 2 3000 series have used this on 4 of them. Hope this help every one
@Infiniteatrophy8 ай бұрын
4 years later, still no part numbers
@mikedarrow3809 Жыл бұрын
I have a Ford 4500 backhoe similar to this. Cool old tractors.
@Louisthebird Жыл бұрын
Part numbers?
@roberttischer3056 Жыл бұрын
Parts # where' ?
@silverdragontaylir82522 жыл бұрын
Genius
@stevenjordan63892 жыл бұрын
before you pull steering wheel remove the nut then spray brake cleaner on rag wrap around the shaft cover that with a spray can cap add brake cleaner several times.Should be able to woble the wheel by hand.
@willhorting53172 жыл бұрын
👍👍 My parents post digger didn't have a hole in the case casting like your's. So my dad welded a short piece of heavy wall 1-1/4" pipe to the side (where you put the horseshoe, above the auger). Then we would stick an old railroad spike bar in the pipe. Dad would remain on the tractor, to operate the up/down action to clean out the loose dirt, while I would pull down on the bar. Always had to be super careful, so I wouldn't get caught by the auger!!! If we hit a rock, or if it hadn't rained for a while and the ground was quite hard, then Dad would get off the tractor and help me. (This was half-century ago.)
@bp-eu6sh2 жыл бұрын
hmm manuel is his name...
@N3ttwerk2 жыл бұрын
Nice tractor, I have the same one handed down from my father. Where did you get that red foot step from? I need that.
@bobqwhite12672 жыл бұрын
I'm 57 soon to be 58 God's will easy trick put diesel around the rim and tire 😀😀😀😀😀😀👍 😳 OMG one or two walks with the hammer done. Putting the tire back on even easier 🙏
@jesusgonzalez84372 жыл бұрын
Does the Ford 3400 has the same system?
@davidlarson48672 жыл бұрын
So disappointing when anything goes wrong, so many people just take God’s name in vain
@matg9 Жыл бұрын
Truly sad
@Jcreek20110 ай бұрын
Goddamnit Bobby
@steveenloe26282 жыл бұрын
Exact same tractor thank you much !
@alexcampbell53712 жыл бұрын
Very nice
@Buckinghamrabbit2 жыл бұрын
just checkin but, did you back your truck into it *before* you jacked the tractor up?
@craigkennedy4813 жыл бұрын
That was the bushing that fits inside if the rubber bushing directly under the steering wheel
@ryderdintwa54583 жыл бұрын
How do you bleed 7840 tractor hydraulic steering wheels system
@danieltravis28504 жыл бұрын
That was not a Speedi Sleeve, Speedi Sleeves are not split. That looked more like the sleeve driver. Speedi Sleeves actually work really well when installed properly. Also, there is another seal at the top of the steering shaft that helps keep water out of the tube.
@billclifton84003 жыл бұрын
Exactly, in fact it looks like a speedy sleeve is on the shaft but down too far.
@mongomay14 жыл бұрын
The bottom o-ring was replaced how?
@mongomay13 жыл бұрын
Watched again, now I got it.
@tonygthelegend36214 жыл бұрын
Thanks for an awesome video ! Do you know the part numbers for everything you need to do this job?
@JasperMogie4 жыл бұрын
How did you get the shaft seal out of the column?
@corbinsherrell9404 жыл бұрын
A long pipe or socket extension run through it. I just flipped it and slammed it on the counter
@dennisvanhoozer38494 жыл бұрын
When replacing the seal which direction does it go? Does the spring side go toward the fluid?
@corbinsherrell9404 жыл бұрын
The lip faces fluid. If you think of a side cutaway view, the pressure will build on one side of it because it wedges itself tighter. If you were to put pressure or fluid on the other side it would just kind of open and push fluid out. This is a good mechanical rule to think about anytime a seal is involved. Some don't matter. Some do. This analysis will always remember assure you. I've put things together "as it came apart" but the older stuff the last guy could have put in wrong. On a hydraulic piston there are lipped seals, several facing both ways because fluid on both sides. To answer your question: down. This particular seal and set up the fluid is below the seal. Thus the top side (smooth and flat side of seal) is up. That side should stay dry
Пікірлер
you bought the wrong kit not saying it wont work but yesterdays tractor has the correct sleeve and seal kit part Item #: 173253 $52 plus shipping no jacking around and works. I own 3 2000 and 2 3000 series have used this on 4 of them. Hope this help every one
4 years later, still no part numbers
I have a Ford 4500 backhoe similar to this. Cool old tractors.
Part numbers?
Parts # where' ?
Genius
before you pull steering wheel remove the nut then spray brake cleaner on rag wrap around the shaft cover that with a spray can cap add brake cleaner several times.Should be able to woble the wheel by hand.
👍👍 My parents post digger didn't have a hole in the case casting like your's. So my dad welded a short piece of heavy wall 1-1/4" pipe to the side (where you put the horseshoe, above the auger). Then we would stick an old railroad spike bar in the pipe. Dad would remain on the tractor, to operate the up/down action to clean out the loose dirt, while I would pull down on the bar. Always had to be super careful, so I wouldn't get caught by the auger!!! If we hit a rock, or if it hadn't rained for a while and the ground was quite hard, then Dad would get off the tractor and help me. (This was half-century ago.)
hmm manuel is his name...
Nice tractor, I have the same one handed down from my father. Where did you get that red foot step from? I need that.
I'm 57 soon to be 58 God's will easy trick put diesel around the rim and tire 😀😀😀😀😀😀👍 😳 OMG one or two walks with the hammer done. Putting the tire back on even easier 🙏
Does the Ford 3400 has the same system?
So disappointing when anything goes wrong, so many people just take God’s name in vain
Truly sad
Goddamnit Bobby
Exact same tractor thank you much !
Very nice
just checkin but, did you back your truck into it *before* you jacked the tractor up?
That was the bushing that fits inside if the rubber bushing directly under the steering wheel
How do you bleed 7840 tractor hydraulic steering wheels system
That was not a Speedi Sleeve, Speedi Sleeves are not split. That looked more like the sleeve driver. Speedi Sleeves actually work really well when installed properly. Also, there is another seal at the top of the steering shaft that helps keep water out of the tube.
Exactly, in fact it looks like a speedy sleeve is on the shaft but down too far.
The bottom o-ring was replaced how?
Watched again, now I got it.
Thanks for an awesome video ! Do you know the part numbers for everything you need to do this job?
How did you get the shaft seal out of the column?
A long pipe or socket extension run through it. I just flipped it and slammed it on the counter
When replacing the seal which direction does it go? Does the spring side go toward the fluid?
The lip faces fluid. If you think of a side cutaway view, the pressure will build on one side of it because it wedges itself tighter. If you were to put pressure or fluid on the other side it would just kind of open and push fluid out. This is a good mechanical rule to think about anytime a seal is involved. Some don't matter. Some do. This analysis will always remember assure you. I've put things together "as it came apart" but the older stuff the last guy could have put in wrong. On a hydraulic piston there are lipped seals, several facing both ways because fluid on both sides. To answer your question: down. This particular seal and set up the fluid is below the seal. Thus the top side (smooth and flat side of seal) is up. That side should stay dry
The spring side is always the "wet" side