Пікірлер

• 
  @paddiman77224 күн бұрын

  Sehr Gut!

• 
  @dariushmilani676026 күн бұрын

  Enjoyed the making of the solid tool post. Liked and Subscribed.👍👍

• 
  @Pawcu4ever28 күн бұрын

  Hello, thank you for this really informative 😊 just for my knowledge, instead of welding it, couldn't you just heat it up using the tig torch and let it cool down? That way you won't have to turn the weld down everytime. Thanks 😊

• 
  @Pawcu4ever28 күн бұрын

  Just read the other comments and realised that someone else suggested something similar 😅 thanks anyways for your videos!

• 
  @bartharkemametalworks229927 күн бұрын

  @Pawcu4ever Yes you could heat it up but the effect of welding is more, and personally I have a bit more control in small areas. This shaft was short and needed a tight bend. If it was longer, bigger or less bend than I would only heat it up. The effect is also relative the diameter of the shaft. Small shaft like this has little effect on heating up with a torch. You heat up almost the entire shaft (unless you have a very powerful and small torch) and ten there is little cold steel to keep it in place, so that the heated area can pull it straight when it cools down. When the whole shaft is heated and cooled it just expand and shrink but no straightening.

• 
  @Pawcu4ever27 күн бұрын

  I see ok that makes sense. Thanks for this! Thank you for your videos and for your feedback!

• 
  @abetterday6987Ай бұрын

  beautyfull

• 
  @RustyInventions-wz6irАй бұрын

  Very nice machine.

• 
  @mrpurple20222Ай бұрын

  Hi Bart, I have the same machine here in Australia that I’m currently restoring. Mine is missing the cross slide and compound slide lock levers. I see you play with it quickly in your video but I’m unsure of how they’re meant to function. If you can help me describe them and the function or pull one out and send me some photos please reach out!

• 
  @bartharkemametalworks2299Ай бұрын

  Sure, send me a mail to bartharkema at g mail dot com. Or Instagram private message.

• 
  @howardtoobАй бұрын

  Any idea how to decode the serial number?

• 
  @bartharkemametalworks229928 күн бұрын

  Yes! Its a Japanese calendar thing. Take the first two numbers of the serial number tag and add 25. This was the year the machine was made. The second set is the month. The last 4 numbers are the serial nr.

• 
  @jmol2049Ай бұрын

  Hi Bart, heb je normale euro95 gebruikt?

• 
  @bartharkemametalworks2299Ай бұрын

  Nee petroleum voor schoonmaken

• 
  @vandalsgarageАй бұрын

  My Cincinnati lathe has the same convention regarding the sliding and facing power feeds. I can change direction of the leadscrew without stopping the spindle (at reasonably slow speeds) via a dog clutch on the threading gear box.

• 
  @witoldkrawczyk3445Ай бұрын

  I would place the tube between the flat bars and press with a press. Good work.

• 
  @PavelKraus_webdesign2 ай бұрын

  Small suggestions: Please move the welder away from the iron dust next to the grinder. Thank you very much for the inspiration with the height-adjustable table.

• 
  @mudnducs2 ай бұрын

  It’s good to see you back!!! Ooops, didn’t realize this was an old video. 😮

• 
  @rascalwind2 ай бұрын

  What color was that dark blue/Gray you used?

• 
  @YooProjects2 ай бұрын

  Great idea! Fantastic job

• 
  @jantoreaga59202 ай бұрын

  Awsome job!

• 
  @jefflewis58522 ай бұрын

  wow, what a job, just looking to buy a bead roller and some of your ideas are going to get put into my project BR, cheers for the Fab video.

• 
  @MechYashesh2 ай бұрын

  I need a mannual for Jones and Shipman 1011 machine can anyone have it?

• 
  @petermetaxas96962 ай бұрын

  I'm going to take apart the tool post on my LS again and check the multi-positional function gears. I know I get the 90deg positions plus some others but not as it appears in Bart's video. I'm so enjoying this 'lathe porn' as my wife calls it.

• 
  @petermetaxas96962 ай бұрын

  My LS tool post [original] can be set at angles others than the four 90's . Where is the carriage lock? can't find it on my LS !!

• 
  @petermetaxas96962 ай бұрын

  Great lathes. The gear is a sacrificial gear, I think the original is made of a fiber as I recall. I made a new one because on my LS one of the teeth had a chip. I made a few extras, if you need one look me up on the internet just type in my name. Prince Edward Island Canada.

• 
  @cuarlosabatcardonagarro89513 ай бұрын

  Buenas donde se puede comprar esa maquina

• 
  @mgbrv83 ай бұрын

  Would love to see more on Bugatti itself

• 
  @mudnducs3 ай бұрын

  What was that second belt you used to put the chamfers on the mounting bar? You started out with a red sanding belt then switched to a shiny silver colored belt.

• 
  @mudnducs3 ай бұрын

  Great eye!!!

• 
  @mudnducs3 ай бұрын

  Nice job Paul!!

• 
  @mosfet5003 ай бұрын

  Thank you for your video. With due respect I disagree with Robin somewhat on these solid tool posts. This is a tool room lathe, it is designed to work within specific parameters and Schaublin knows very well how to design lathes. When we change out the standard compound tool post for the solid tool post we limit the versatility of the lathe. Let's understand tool room lathes are not CNC lathes, CNC lathes do work better with solid tool posts because they have different parameters and they are controlled by computers that enable them to machine any angle required. Are we saying that the original tool post can't make as quality a cut as the solid tool post? I think we can make equal cuts with either and I'm sure Schaublin would never let a lathe leave its factory that made inferior cuts. I will say that I have personally made a solid tool post and I do use it but I still use my standard tool post for certain machining operations, especially tapers which do not work well with solid tool posts. Older lathes do not work as well with modern carbide and ceramic tooling because they involve higher tool pressures and speeds. Also, it is not always possible to take finer cuts with modern tooling without having several different carbides for different cut depths and materials which small shops aren't always capable of affording. With that said older lathes work very well with tangential cutters because they require less pressure, in fact older lathes work better with HSS cutters overall. With carbides there is a benefit to the solid tool post but the benefit is from speed not overall cut quality. The other problem is the material the solid tool post is made from. Steel has a tendency to add resonance to cutting. I did verify this making both a steel and cast iron tool post. On heavy cuts the steel gave out a high pitch whine. If someone is hitting the tail stock with the compound then they are not using the lathe correctly.

• 
  @Keith_the_knife_freak3 ай бұрын

  That is great work.. thanks for sharing

• 
  @sergeirahklei34644 ай бұрын

  Красавчик

• 
  @JonDingle4 ай бұрын

  I like that, well done young man!

• 
  @bartharkemametalworks22994 ай бұрын

  Thank you 👍

• 
  @jameshaliday19294 ай бұрын

  nice job but base ,angle brackets 2 times the size you have ,and how about using old riding mower axles and steering with solid steel /rubber wjeel,woiuld be dope.

• 
  @bartharkemametalworks22994 ай бұрын

  Thanks. I didn't want bigger brackets or steering because it was designed to be small and easy to transport on a trailer when I pick up machines. It's not ment to move around under load. And I can support the structure with straps if I need too. But if it was not designed for small transport I would have definitely made it bigger 👍

• 
  @richarddawson9844 ай бұрын

  I like that baler on the shelf

• 
  @wyliemacbean11574 ай бұрын

  I know I am a little late to this video but ABSOLUTELY FANTASTIC job. Very, very impressed. Thank you for posting.

• 
  @bartharkemametalworks22994 ай бұрын

  Never too late 😉. Thanks

• 
  @Cpoole424 ай бұрын

  I just got my own Okuma LS home to the shop and set up. A big thank you for this series, has helped alot in sorting through the ins and outs. That brake addition is interesting on your lathe, do you have any further information on it? Mine has some remnants of a manual type brake but not electrically driven. Thanks again!

• 
  @Dancing_Alone_wRentals4 ай бұрын

  I never knew welding could look so nice. tHanks for the video

• 
  @melkalyetv77514 ай бұрын

  You have amazing tools to modify a piece of equipment

• 
  @user-wy8tt8cs6v4 ай бұрын

  Лучше бы припаял латунью.После сварки без проковки зерно крупное и металл хрупкий.

• 
  @shrikantauti85784 ай бұрын

  very nice explanation friend, Great job.

• 
  @fearlyenrage5 ай бұрын

  Nice vieo thy. Would you buy the 102VM again?

• 
  @Jan_Raap5 ай бұрын

  Great work! Thank you for filming and sharing. Looking forward to seeing a few bits you grind with your surface grinder.

• 
  @a.bakker645 ай бұрын

  Leuk weer eens wat van jou te zien Bart! Heb eens voor een eindproject van MTS Wtb een langsgeleiding gemaakt voor de Pullmax. Dit was met 2 haaks op elkaar staande zwaluwstaarten. De ene was voor de hoogte verstelling van de langsgeleiding en de andere was voor de onderste geleiding van de Pullmax. Zo kon je een volle plaat op maat knabbelen.

• 
  @tharaniengineering63575 ай бұрын

  Let me know about head stock lubrication pump and oil filling areas.

• 
  @slicktires20115 ай бұрын

  Great work! I've never seen this type of QCTP before, with a round side and splines. Is that system better than the common dovetail type?

• 
  @bartharkemametalworks22995 ай бұрын

  It's common, especialy in Europe. Its called Multifix. The benefit is that you can fix the tool at different angles on the spline.

• 
  @Ibonneau5 ай бұрын

  Great work. Love your videos. I own a 102vm myself and would love to make a solid tool post for it. Any chance you have a drawing or cad file i can use as reference?

• 
  @Anatheme-5 ай бұрын

  look at Multifix size As it has a better fit on the 102.

• 
  @a.bakker645 ай бұрын

  Hé Bart, lang niet gezien. Mooi draaibankje.

• 
  @briansmart20455 ай бұрын

  Very nice and thoughtful of you to refurbish your Grandfathers work , am sure your family is grateful . Thank you for filming it for all to see . Kind regards Brian

• 
  @mudnducs5 ай бұрын

  Excellent!!!

• 
  @bobweiram63215 ай бұрын

  Your gift to Mark was a super kind and thoughtful gesture not only to him, but to all of his subscribers. Thanks to you his content won't be delayed on account of broken end mill.

• 
  @paulsmith29606 ай бұрын

  Enjoyable video Bart and inspiring too. I have the same bead roller. Nice touch with the split screen shots. 👍

• 
  @bartharkemametalworks22996 ай бұрын

  Thanks!

• 
  @movax20h6 ай бұрын

  Looks amazing. Thanks for the video.

• 
  @bartharkemametalworks22996 ай бұрын

  Thanks