Hi Jason QUEBEDEAUX I have the same problem l would to get a plate with you.
@Outside_TheboxАй бұрын
How to you get the pvc to smoke
@JoseTrejo1Ай бұрын
What you see smoking is primarily the parking lot, It had just been refinished.
@joewinsor90122 ай бұрын
Mine has a shift problem that just started. It's 6 years old and just started. Reverse works fine. In drive it goes, but will buck and grind a little, like something is slipping a little. Any thoughts that this could be related to your shift issues?
@JoseTrejo12 ай бұрын
Yes. The gears are pretty solid for the unit design. Typically it’s just not engaging all the way like it should. You likely rounded the gear out where it was making contact. How many miles or hours on the unit? Doing the rebuild isn’t that difficult if you have a little know how and willingness to dive into it, it’s just a little time consuming. Please send me a email (see video description) and we can discuss it further if you would like.
@spike27943 ай бұрын
Chinese junk.
@scubasteve79463 ай бұрын
Brilliant
@nestorespinoza32354 ай бұрын
Yes please how can I get this I have a Colman ut400 with the same issue
@JoseTrejo14 ай бұрын
Contact info located in video description
@JeffKnoxAZ5 ай бұрын
Thanks. Good to know. I'm about to try adjusting the cable, as mine doesn't engage Forward immediately -- slips, then clacks, then pops in. Now to figure out why it's not shifting out of 4WD...?
@JoseTrejo15 ай бұрын
It could very well be the switch. As a heads up, While I was servicing the Coleman 400utv I found various connections not fully connected where the retention clip was not even engaged over the locking tab on the receiving connector. I was blown away at the lack of execution taken on this machine. Go over your connections and make sure everything is properly seated and secure. You can likely check continuity of the 4wd switch if you have a meter.
@JeffKnoxAZ5 ай бұрын
Thanks a lot for the response. I think it probably is the switch, either a bad contact or other bad connection. Tomorrow. Thanks again.
@daltonpingleton79826 ай бұрын
What throttle cable are you using?
@JoseTrejo16 ай бұрын
Custom made throttle cable. I cut the conduit to length. Cut the cable to length on the carburetor side if it doesn’t have correct barrel end needed. Then using a block of wood I drilled the diameter and depth needed for a new barrel end that would fit into the carburetor slide. Put the cut cable end into the hole you drilled and solder it up. Once it’s cooled off, pull it out of the wood and file it down to fit. You may have to do this a couple times so practice on the scrap cable. I also sometimes frey the end of cable for better grip to the solder with less chance of pulling off. Hope this helps.
@simongarcia27636 ай бұрын
How much does the sleeves last?
@dxcenataker6 ай бұрын
Needs a blow off valve
@garymattison95198 ай бұрын
I need to get one of these brackets! Could you pass me the info that I would need to get one?
@JoseTrejo18 ай бұрын
Please email me directly at [email protected] I will have the machine shop get a few made up this week and ship when I get back from vacation
@chimonoki28689 ай бұрын
Now do it without pvc pipe
@Ez_Di3cast Жыл бұрын
This is one of the coolest things I've ever seen
@rusty1253 Жыл бұрын
The engine sounds good tbh
@n8dagr881 Жыл бұрын
Pbc pipe for the skids
@JoseTrejo1 Жыл бұрын
Yes sir
@GONECHECK Жыл бұрын
Ничего себе 😮 у меня так не дымятся сколько не крути 👺🔥
@westtexasworkshop26283 жыл бұрын
So this is what bear grills does in his free time
@southcentraloutdoorliving74215 жыл бұрын
nice track bro, I subbed. check out my bike track I just started my utube
@rdrc35155 жыл бұрын
This is awesome! Are these the karts you've been building yourself?
@JoseTrejo15 жыл бұрын
These are purchased karts. Too cheap to pass up. Almost done with the first home built kart.
@callummurry72187 жыл бұрын
I am making one at the moment and i have a few questions, can you please answer them 1) how many teeth are on the sprocket 2) how did you do the throttle (like how did you connect did you use a brake for it or did you use a spring
@JoseTrejo17 жыл бұрын
Woodie Films the tooth count on the sprocket is upto you, you can buy a sprocket hub and a just get the split sprockets(55-65tooth), if you find it a little hard to spin the tires then swap in a smaller sprocket. The throttle is specifically for the carburetor, it has a small bullet end on the carb side and a regular brake bullet on the brake lever end. You can buy an actual thumb or twist grip if you prefer that better. Twist grip makes a little harder to hold when turning left so i chose a regular brake lever over a short thumb lever. If you need a video of the parts specifically on how it was setup, let me know and i can do that this sunday. Thanks, happy drifting
@callummurry72187 жыл бұрын
Can you please do a Vedio on your parts Thanks Woodie Films
@redorrick4276 жыл бұрын
its a mikuni carb. it has its own throttle
@dillonharrison36657 жыл бұрын
My motor idles too high when I start it with the choke on but if I turn down the idle it dies with the choke off did you have this problem at all?
@JoseTrejo17 жыл бұрын
Dillon Harrison you need to set your idle with the choke off only. Do not set your idle with the choke on. It is perfectly normal for it to idle high with choke on. Hope this helps
@Marc-sv1gt7 жыл бұрын
6,5 hp? 212 cc?
@JoseTrejo17 жыл бұрын
Marc Roig Prunell it is a modified 6.5hp predator
@Marc-sv1gt6 жыл бұрын
Witch parts? Exhaust, filter , jet? And Anything more? Thanks.
@JoseTrejo16 жыл бұрын
Marc Roig Prunell kzread.info/dash/bejne/loaA2ZV8pci6d9o.html
@beatrizcamargo28217 жыл бұрын
video maneiro
@ppplild7 жыл бұрын
how many pvc sleeves have you split on that road?
@JoseTrejo17 жыл бұрын
Lil Dee none yet
@mikemk26817 жыл бұрын
Top speed?
@JoseTrejo17 жыл бұрын
Calculated speed based on wheel size, sprocket size and top engine speed puts it at about 65mph
@BygRed8 жыл бұрын
is this a hf 6.5?
@JoseTrejo18 жыл бұрын
Yes sir, build info is below the video title
@BygRed8 жыл бұрын
+Blown84Turismo wow you did some serious work to that, any idea on hp now?
@JoseTrejo18 жыл бұрын
Not sure on the hp, the key components were the connecting rod and flywheel along with the governor delete so i could achieve higher speeds.
@finestpker9 жыл бұрын
Awesome man, is it allowed to drive on public roads though?
@JoseTrejo18 жыл бұрын
No comment
@dogy2399 жыл бұрын
potentially stupid question but was the gauge for miles per hour or kilometers per hour?
@JoseTrejo19 жыл бұрын
Sloan Rich Its in MPH
@gearheadgriffin9 жыл бұрын
Too cool Jose, it's hilarious watching the rear end try to get away from you. Nice work brother, have fun be safe.
@Outsidealot11 жыл бұрын
whatcha got for motors and esc in it?
@MyPuppers13 жыл бұрын
sorry to hear about the boats. hope the super one comes out fine. now the trick is to fix er up, but not add to much weight in the process. take er easy and good luck!
@JoseTrejo113 жыл бұрын
@MyPuppers Thank you.. she was quick.. she needs hull repairing now. Thank my wife's crazy driving. she went head on with my miss elam by time i let of the throttle miss elam and super hawaii were upside down. miss elam was total'd and the super hawaii hull split. i got a new hull for miss elam so now it's just gutting out super hawaii and figuring out how i want to repair it. i have room to play with for battery power. just need to strengthen up the hull. it's in the works when i have time.
Пікірлер
Hi Jason QUEBEDEAUX I have the same problem l would to get a plate with you.
How to you get the pvc to smoke
What you see smoking is primarily the parking lot, It had just been refinished.
Mine has a shift problem that just started. It's 6 years old and just started. Reverse works fine. In drive it goes, but will buck and grind a little, like something is slipping a little. Any thoughts that this could be related to your shift issues?
Yes. The gears are pretty solid for the unit design. Typically it’s just not engaging all the way like it should. You likely rounded the gear out where it was making contact. How many miles or hours on the unit? Doing the rebuild isn’t that difficult if you have a little know how and willingness to dive into it, it’s just a little time consuming. Please send me a email (see video description) and we can discuss it further if you would like.
Chinese junk.
Brilliant
Yes please how can I get this I have a Colman ut400 with the same issue
Contact info located in video description
Thanks. Good to know. I'm about to try adjusting the cable, as mine doesn't engage Forward immediately -- slips, then clacks, then pops in. Now to figure out why it's not shifting out of 4WD...?
It could very well be the switch. As a heads up, While I was servicing the Coleman 400utv I found various connections not fully connected where the retention clip was not even engaged over the locking tab on the receiving connector. I was blown away at the lack of execution taken on this machine. Go over your connections and make sure everything is properly seated and secure. You can likely check continuity of the 4wd switch if you have a meter.
Thanks a lot for the response. I think it probably is the switch, either a bad contact or other bad connection. Tomorrow. Thanks again.
What throttle cable are you using?
Custom made throttle cable. I cut the conduit to length. Cut the cable to length on the carburetor side if it doesn’t have correct barrel end needed. Then using a block of wood I drilled the diameter and depth needed for a new barrel end that would fit into the carburetor slide. Put the cut cable end into the hole you drilled and solder it up. Once it’s cooled off, pull it out of the wood and file it down to fit. You may have to do this a couple times so practice on the scrap cable. I also sometimes frey the end of cable for better grip to the solder with less chance of pulling off. Hope this helps.
How much does the sleeves last?
Needs a blow off valve
I need to get one of these brackets! Could you pass me the info that I would need to get one?
Please email me directly at [email protected] I will have the machine shop get a few made up this week and ship when I get back from vacation
Now do it without pvc pipe
This is one of the coolest things I've ever seen
The engine sounds good tbh
Pbc pipe for the skids
Yes sir
Ничего себе 😮 у меня так не дымятся сколько не крути 👺🔥
So this is what bear grills does in his free time
nice track bro, I subbed. check out my bike track I just started my utube
This is awesome! Are these the karts you've been building yourself?
These are purchased karts. Too cheap to pass up. Almost done with the first home built kart.
I am making one at the moment and i have a few questions, can you please answer them 1) how many teeth are on the sprocket 2) how did you do the throttle (like how did you connect did you use a brake for it or did you use a spring
Woodie Films the tooth count on the sprocket is upto you, you can buy a sprocket hub and a just get the split sprockets(55-65tooth), if you find it a little hard to spin the tires then swap in a smaller sprocket. The throttle is specifically for the carburetor, it has a small bullet end on the carb side and a regular brake bullet on the brake lever end. You can buy an actual thumb or twist grip if you prefer that better. Twist grip makes a little harder to hold when turning left so i chose a regular brake lever over a short thumb lever. If you need a video of the parts specifically on how it was setup, let me know and i can do that this sunday. Thanks, happy drifting
Can you please do a Vedio on your parts Thanks Woodie Films
its a mikuni carb. it has its own throttle
My motor idles too high when I start it with the choke on but if I turn down the idle it dies with the choke off did you have this problem at all?
Dillon Harrison you need to set your idle with the choke off only. Do not set your idle with the choke on. It is perfectly normal for it to idle high with choke on. Hope this helps
6,5 hp? 212 cc?
Marc Roig Prunell it is a modified 6.5hp predator
Witch parts? Exhaust, filter , jet? And Anything more? Thanks.
Marc Roig Prunell kzread.info/dash/bejne/loaA2ZV8pci6d9o.html
video maneiro
how many pvc sleeves have you split on that road?
Lil Dee none yet
Top speed?
Calculated speed based on wheel size, sprocket size and top engine speed puts it at about 65mph
is this a hf 6.5?
Yes sir, build info is below the video title
+Blown84Turismo wow you did some serious work to that, any idea on hp now?
Not sure on the hp, the key components were the connecting rod and flywheel along with the governor delete so i could achieve higher speeds.
Awesome man, is it allowed to drive on public roads though?
No comment
potentially stupid question but was the gauge for miles per hour or kilometers per hour?
Sloan Rich Its in MPH
Too cool Jose, it's hilarious watching the rear end try to get away from you. Nice work brother, have fun be safe.
whatcha got for motors and esc in it?
sorry to hear about the boats. hope the super one comes out fine. now the trick is to fix er up, but not add to much weight in the process. take er easy and good luck!
@MyPuppers Thank you.. she was quick.. she needs hull repairing now. Thank my wife's crazy driving. she went head on with my miss elam by time i let of the throttle miss elam and super hawaii were upside down. miss elam was total'd and the super hawaii hull split. i got a new hull for miss elam so now it's just gutting out super hawaii and figuring out how i want to repair it. i have room to play with for battery power. just need to strengthen up the hull. it's in the works when i have time.
holy crap dude!! she is quick! nice vid.