Do you like the size of this tractor or do you wish you had gone bigger …… looking to purchase one this summer and not sure if I should go bigger
@CORKO772 ай бұрын
What model and size blower are you running? Great video!
@bernardsimonet94774 ай бұрын
Pourquoi mettre la fraiseuse à l arrière? Mal mis pour travail et conducteur dans 1 position inconfortable! Je ne cautionne pas, je trouve cela idiot. Vive le torticolis.
@toddmathers62247 ай бұрын
What do you have for a blower?
@docjewell46588 ай бұрын
Great for your first time👍
@jeffheath263010 ай бұрын
Just bought a CK3510 and a snowblower attachment, cant wait to mive some snow here in upper NH. where did you find your safety light? Thats one thing I need to add before I start.
@kioti-fred10 ай бұрын
Hello! I bought it on Amazon and wired it through the right wheel well. I made the bracket using a small aluminum L piece.
@maxball6388 Жыл бұрын
Video clarity is great. How is the HST whine in the cab?
@kioti-fred Жыл бұрын
Really not that bad, if you compare with the other brand!
@maxball6388 Жыл бұрын
@@kioti-fred I am comparing as Im quite tired of it…
@kioti-fred Жыл бұрын
I have heard the replacement for LX2610 from Kubota has a new transmission which is supposed to have reduced whine a lot!
@maxball6388 Жыл бұрын
@@kioti-fred new LX20 series. The LX3520SU cab is available to build on their website. No suspension seat, no mid pto- which I dont use anymore… $40,000usd. Saving 8k by ordering a CK2620se cab.
@kioti-fred Жыл бұрын
Yep, you get way more for your money if you go Kioti! I like mine a lot.
@philipsmith881 Жыл бұрын
Any way we can get a detailed video of the tractor and blower? I own the same tractor and have been thinking about a blower for the back. I currently run. A ZMI 920 pusher on the front. Thanks .
@kioti-fred10 ай бұрын
I will try to make a detailing video for next winter. I would love a pusher on the front also...! How you like it? As for the blower, my neck wish its in the front!!
@philipsmith88110 ай бұрын
Pusher works pretty good. Need to weigh a little more but I can stack snow as high as the loader lifts. Thanks 👍
@rwb409 Жыл бұрын
Why do you shut the pto off everytime you drive ahead ? Nice set up.
@kioti-fred Жыл бұрын
Thanks! Because it prevents unnecessary wear on the pto shaft, running it at an angle like that is very bad.
@Smittyschannel Жыл бұрын
Why do people not start in the middle & work outwards? Every pass you make gets blowing runoff from the chute right onto the previous pass where you just removed snow. Or if you're only blowing towards the house, start on the far left & make passes towards the right as you go
@kioti-fred10 ай бұрын
You are probably right! I am still quite new at this, only 60 hours on my first tractor and the fact is that the longer it takes, the better! haha :)
@thegreatnorthwoodswithbb2863 Жыл бұрын
Nice setup
@kioti-fred Жыл бұрын
Thanks sir!
@kindagitnrdoneinvermont6057 Жыл бұрын
Nice job. It looks like the tractor handles that snowblower pretty well 💪
@kioti-fred Жыл бұрын
Yes it does! Thanks! 👍
@wireedm1 Жыл бұрын
Great video! You've got to love those R14 tires in the snow!
@kioti-fred Жыл бұрын
Yes! They weren't my first choice but I am glad I went with them.
@youtubecreators284tanoskitchen Жыл бұрын
Wow So Amazing Video 👍🌹👌🌹
@kioti-fred Жыл бұрын
Thanks for watching! 😎
@swamprat69er Жыл бұрын
Gotta love it, blowing snow in your shirt sleeves in the middle of winter. Heated cabs are the BEST! I have the necessary 'revers-er' to hook up a Kioti CK 27hst front mount blower. You need a mid mount PTO to run this thing. I think it will fit your 2610 and you can use your rear mount blower. Check with your Kioti dealer. If you want it I think we can 'cut a deal'. I am going to put my blower on the rear next winter. I'm outside North Bay, ON.
@kioti-fred Жыл бұрын
Really like cabs indeed! For now I am not investing more money on this, I need to renovate the garage with a bigger door so I can store the Kioti inside! This is quite an investment... Thanks though!
@backyardcountrylivin1514 Жыл бұрын
Enjoyed the video. Man that’s a lot of snow. We wouldn’t know what to do down here in eastern NC with that much snow. I have the ck3510 and it has served me well for almost 2 years now. Really like the snow blower set up you have and I know the cab is a must in weather like that. I’ve done a few videos with mine, but still getting used to the you tube thing. I subscribed to your channel.
@kioti-fred Жыл бұрын
Thanks sir! I have subscribed to yours also!
@dlansburg2673 Жыл бұрын
What size blower,good job on the video
@kioti-fred Жыл бұрын
This is a 66 inches blower with a 14 inches 4 pales rotor.
@robertrockwell7581 Жыл бұрын
nice job. but would not even consider buying a tractor with a blower on the back. do not like them.
@kioti-fred Жыл бұрын
I agree, I would rather have a front blower but they are three times the price! Maybe for my next tractor :)
@danwake4431 Жыл бұрын
they are the only option if your tractor only has a rear PTO. you need a mid pto for a front blower.
@kioti-fred Жыл бұрын
Yes, my dealer told me 600$ CAD for installing a mid PTO, not that expensive.
@botadriver Жыл бұрын
Hi Fred Thanks for sharing? What are are you in? You sure get a lot of snow.
@kioti-fred Жыл бұрын
Hehe yes we get a lot of snow! I am in eastern Quebec and winter is quite a long season here!
@botadriver Жыл бұрын
Nice, I was thinking Gaspe or Northern NB. Thanks! Snow is made there lol
@kioti-fred Жыл бұрын
@@botadriver haha yes winter is way more fun since I bought this tractor 😅
@sewerman911 Жыл бұрын
Tractor did great. Tough to find s spot to put it all. Spring thaw must be interesting.
@kioti-fred Жыл бұрын
Indeed, thinking about pushing it all out the driveway and blow it on the sides now..!😁
@Morpheen999 Жыл бұрын
Imagine if all you can was a pusher or a blade? where would you pile all that snow! With a snowblower being able to throw it a distance really helps
@prepper1013 Жыл бұрын
Fred, are you the only one in your neighborhood that has one of those bad boys and if so do they ask you to plow their driveways?
@kioti-fred Жыл бұрын
Yes I am the only one and I usually go for a ride with the tractor after cleaning my driveway and it happened a couple of times that some neighbors were shoveling. I then offered my help, its always a pleasure for me to help but I won't plow their driveway if they won't ask for it, some of them really enjoy doing it I dont want to steal this from them. 😁
@KubotaL4060 Жыл бұрын
Nice video and equipment. I rarely get enough snow to justify my similar blower, but nothing beats them in big dumps. FYI, you may want to just barely raise the blower off the ground while maneuvering between actually blowing snow. A severe angle on the pto shaft wears the universals significantly (like by a factor of 10 between 5 degrees and 20 degrees).
@kioti-fred Жыл бұрын
Thanks sir! I didn't know that about the PTO angle, thanks for the tip.
@swamprat69er Жыл бұрын
If you lower the skid shoes, then you wont throw as many stones.
@kioti-fred Жыл бұрын
Now that its icy and packed it doesn't happen anymore but yes I am lazy 😆
@swamprat69er Жыл бұрын
My Dad was stationed there during WW2. He was a armourer.
@kioti-fred Жыл бұрын
Thanks for his service
@kindagitnrdoneinvermont6057 Жыл бұрын
Nice job 💪. I don’t use a snowblower. What RPM you run at when using? Just curious, thanks 😊.
@kioti-fred Жыл бұрын
Thanks sir! For implements like my snowblower it must be 540 RPM, might be different for other implements but I am no expert.
@prepper1013 Жыл бұрын
Nice work Fred....What brand, size and model snow plow did you buy and did you buy it online or from a local dealer? I swapped out all 4 of my CK2610 cab work lights with LED's. Man it's like night and day. Pun intended. I got them off Amazon (New EXZEIT 4.4 Inch Led Work Light for Truck, 36W Flood Light Off Road Light Bar for Tractor Golf Cart UTV ATV, 12/24V) They were 28 bucks and easy to install with bullet connectors..
@kioti-fred Жыл бұрын
This is a 66 inches snowblower, brand is Ex-trac and model is "serie 20" for 20-30hp compact tractor. It has a 4 pale 14 inches rotor and yes I bought it from a local dealer. Thanks for all the details about your lights setup, upgrading all lights to LEDs (even turn and brake lights) is my next upgrade.
@prepper1013 Жыл бұрын
@@kioti-fred - I replaced the front headlights with LED's - (OXILAM H7 LED Bulbs Non-Polarity, 6500K Cool White 8 LED Chips No Dark Spot, 1:1 Design No Adapter Required, All-in-One Conversion Kit for Hi/Lo Beam Fog Lights Replacement, Pack of 2) - I tried to replace the front yellow blinkers and white lights to LED, but was having issues with getting the bulbs to connect in the sockets and went back to the original factory light bulbs - (1157 Led Bulb, 2057 2357 7528 BAY15D LED Bulbs for Back Up Reverse Light, Tail Light, Brake Light,Turn Signal Light, Pack of 2pcs Xenon White(6500K) (1157 LED Bulb, BAY15D 7528 2057 2357 LED Bulbs for Back Up Reverse Light, Tail Light, Brake Light,Turn Signal Light, Pack of 2pcs Amber Yellow) - The inside cab light was easy to change to LED - (AUXLIGHT DE3175 DE3021 DE3022 3175 31MM 1.22”Festoon Canbus Error Free LED Interior Light Bulbs 6000K Xenon White, Super Bright 6SMD Chips for Dome Map Door Courtesy License Plate Lights (Pack of 6) - I haven't tried the tail lights yet but its on my bucket list. I heard they're a sealed system. Let me know if you have any luck.
@kioti-fred Жыл бұрын
Very nice information thanks man! Its going to save me a lot of research time.
@kindagitnrdoneinvermont6057 Жыл бұрын
Nice job 💪
@kioti-fred Жыл бұрын
Thanks ✌
@AD-hr4is Жыл бұрын
Hi kioti fred can you do a video on the chute movement. It dosent look like it has no hinge but pivot point and arms.
@kioti-fred Жыл бұрын
Sure, I will do it soon and let you know. Too cold outside these days!! -40c with wind chil!
@AD-hr4is Жыл бұрын
@@kioti-fred of course. When ever the weather and time agrees. Thank you. I made my own articulated for closed quarters and around cars so they dont get plastered by rocks or ice.
@AD-hr4is Жыл бұрын
Nice to see someone else using the same outfit I have . I never see my self cleaning my yard. Does youre cab window fogs?
@kioti-fred Жыл бұрын
Oh yes they do! really annoying... I have bought some anti-fog for windows a few days ago, hope its going to work. Tricks: clean your boots so they aren't full of snow, set your cab air intake to "fresh air" instead of "recyc" and turn down that hot air control to cold :)
@AD-hr4is Жыл бұрын
@@kioti-fred yes i do all the above and it still does it. The only thing that seems to clear it is to put the ac on.
@kioti-fred Жыл бұрын
Will try that!! thanks
@GrampiesWorkshop Жыл бұрын
How's she goin'? Ya gotta love plowing at night. There is just something mesmerizing about it for me anyways!! Thanks for posting and take care!!
@kioti-fred Жыл бұрын
Yes, doing this at night is quite relaxing...I like it a lot! Thinking about swapping the work light for leds or adding a light bar.. there is always something to upgrade :D
@GrampiesWorkshop Жыл бұрын
@@kioti-fred The LEDs will make a big difference and they're easier on the alternator and tractor electrics too.
@kioti-fred Жыл бұрын
Harder on the wallet though!! I don't have 3k subscribers to pay for all this!! haha just kidding ;)
@littleblue4x4 Жыл бұрын
Pretty nice rig you got there! I like that snowblower! Just picked up a used Berco with electric chute since I don't have rear hydraulics and it's a huge improvement over manual crank.
@kioti-fred Жыл бұрын
Thanks sir! Couldn't agree more.. having complete control from the comfort of the cab is awesome..!
@prepper1013 Жыл бұрын
Great video. Did the rear hazard light come with the tractor, or was it a add on? I have the same tractor. Love that dran thing. Can't wait to get a few hours on it to make sure all is good and then ramp up the horse power to 40HP....
@kioti-fred Жыл бұрын
No, the hazard light did not come with it. I simply made a metal bracket and fixed a strobe bought from amazon to it, then passed a new wire through the cab post into the right wheel well. I soldered this cable to a rocker switch and tapped 12v into some cable (don't remember which one, I think it was the work lights 12v). I would love to ramp up hp on that motor too!! Just a little scared with warranty..!
@prepper1013 Жыл бұрын
@@kioti-fred Same here about the warranty. Great videos. Keep em coming..
@markwegner6100 Жыл бұрын
Great job!
@kioti-fred Жыл бұрын
Thanks!
@GrampiesWorkshop Жыл бұрын
How's she goin'? The rear mounted blowers are some powerful eh. Hard on the back though. I installed a rear view camera and it helps a lot!! Lots of snow to clear but you have the gear to do it eh!! Take care!!
@kioti-fred Жыл бұрын
Yes that is hard on the back... I wouldn't be doing this as a full time job for sure!! Sometimes I wish I went with the front blower but couldn't justice 3 times the price..!
@markwegner6100 Жыл бұрын
Great job!
@kioti-fred Жыл бұрын
Thanks sir!
@kayeross486 Жыл бұрын
Great 👍 content!
@kioti-fred Жыл бұрын
Glad you enjoyed it
@botadriver Жыл бұрын
Great machine thanks for sharing!
@kioti-fred Жыл бұрын
Thanks for watching!
@chrislowe4310 Жыл бұрын
Have a similar setup only the CK3510SEHC, goes through pretty much anything I would interested to know how you wired in the strobe light there is a wire harness but I have no idea where it goes or how to wire it up, enjoyed the video.
@kioti-fred Жыл бұрын
Mine did not have the wire harness, or I did not find it. I simply made a metal bracket and fixed the strobe to it, then passed a new wire through the cab post into the right wheel well. I soldered this cable to a rocker switch and tapped 12v into some cable (don't remember which one). It was fairly easy, I should have took pictures...! Good luck!
@fredhinck9685 Жыл бұрын
No 12v accessory socket in the cab???? Lots of these lights plug in.
@kioti-fred Жыл бұрын
Yes there is a 12v socket on top of the wheel well, but thats on the other side. Pretty sure I tapped 12v on the work lights wire.
@kindagitnrdoneinvermont6057 Жыл бұрын
Nice job. Looks like that tractor handles that blower good.
@kioti-fred Жыл бұрын
Yes it does, thanks sir!
@maraudermitchelli Жыл бұрын
I upload snow blowing videos to my channel, I found watching your tractor blow snow very relaxing great job impressive setup 😊
@kioti-fred Жыл бұрын
Thanks sir! I really like your videos too. I subscribed to your channel long time ago and almost bought a 3046r with a front blower because of you hehe
@kindagitnrdoneinvermont6057 Жыл бұрын
Nice job 💪
@kioti-fred Жыл бұрын
Thanks!
@tractortyme Жыл бұрын
That CK2610 did really good, didn't even budge on the RPMS.
@kioti-fred Жыл бұрын
Yes! might not show on screen but that snow was packed and heavy. Ran it mostly on med gear and it performed really well. This tractor chew everything I threw at it hehe
Пікірлер
Do you like the size of this tractor or do you wish you had gone bigger …… looking to purchase one this summer and not sure if I should go bigger
What model and size blower are you running? Great video!
Pourquoi mettre la fraiseuse à l arrière? Mal mis pour travail et conducteur dans 1 position inconfortable! Je ne cautionne pas, je trouve cela idiot. Vive le torticolis.
What do you have for a blower?
Great for your first time👍
Just bought a CK3510 and a snowblower attachment, cant wait to mive some snow here in upper NH. where did you find your safety light? Thats one thing I need to add before I start.
Hello! I bought it on Amazon and wired it through the right wheel well. I made the bracket using a small aluminum L piece.
Video clarity is great. How is the HST whine in the cab?
Really not that bad, if you compare with the other brand!
@@kioti-fred I am comparing as Im quite tired of it…
I have heard the replacement for LX2610 from Kubota has a new transmission which is supposed to have reduced whine a lot!
@@kioti-fred new LX20 series. The LX3520SU cab is available to build on their website. No suspension seat, no mid pto- which I dont use anymore… $40,000usd. Saving 8k by ordering a CK2620se cab.
Yep, you get way more for your money if you go Kioti! I like mine a lot.
Any way we can get a detailed video of the tractor and blower? I own the same tractor and have been thinking about a blower for the back. I currently run. A ZMI 920 pusher on the front. Thanks .
I will try to make a detailing video for next winter. I would love a pusher on the front also...! How you like it? As for the blower, my neck wish its in the front!!
Pusher works pretty good. Need to weigh a little more but I can stack snow as high as the loader lifts. Thanks 👍
Why do you shut the pto off everytime you drive ahead ? Nice set up.
Thanks! Because it prevents unnecessary wear on the pto shaft, running it at an angle like that is very bad.
Why do people not start in the middle & work outwards? Every pass you make gets blowing runoff from the chute right onto the previous pass where you just removed snow. Or if you're only blowing towards the house, start on the far left & make passes towards the right as you go
You are probably right! I am still quite new at this, only 60 hours on my first tractor and the fact is that the longer it takes, the better! haha :)
Nice setup
Thanks sir!
Nice job. It looks like the tractor handles that snowblower pretty well 💪
Yes it does! Thanks! 👍
Great video! You've got to love those R14 tires in the snow!
Yes! They weren't my first choice but I am glad I went with them.
Wow So Amazing Video 👍🌹👌🌹
Thanks for watching! 😎
Gotta love it, blowing snow in your shirt sleeves in the middle of winter. Heated cabs are the BEST! I have the necessary 'revers-er' to hook up a Kioti CK 27hst front mount blower. You need a mid mount PTO to run this thing. I think it will fit your 2610 and you can use your rear mount blower. Check with your Kioti dealer. If you want it I think we can 'cut a deal'. I am going to put my blower on the rear next winter. I'm outside North Bay, ON.
Really like cabs indeed! For now I am not investing more money on this, I need to renovate the garage with a bigger door so I can store the Kioti inside! This is quite an investment... Thanks though!
Enjoyed the video. Man that’s a lot of snow. We wouldn’t know what to do down here in eastern NC with that much snow. I have the ck3510 and it has served me well for almost 2 years now. Really like the snow blower set up you have and I know the cab is a must in weather like that. I’ve done a few videos with mine, but still getting used to the you tube thing. I subscribed to your channel.
Thanks sir! I have subscribed to yours also!
What size blower,good job on the video
This is a 66 inches blower with a 14 inches 4 pales rotor.
nice job. but would not even consider buying a tractor with a blower on the back. do not like them.
I agree, I would rather have a front blower but they are three times the price! Maybe for my next tractor :)
they are the only option if your tractor only has a rear PTO. you need a mid pto for a front blower.
Yes, my dealer told me 600$ CAD for installing a mid PTO, not that expensive.
Hi Fred Thanks for sharing? What are are you in? You sure get a lot of snow.
Hehe yes we get a lot of snow! I am in eastern Quebec and winter is quite a long season here!
Nice, I was thinking Gaspe or Northern NB. Thanks! Snow is made there lol
@@botadriver haha yes winter is way more fun since I bought this tractor 😅
Tractor did great. Tough to find s spot to put it all. Spring thaw must be interesting.
Indeed, thinking about pushing it all out the driveway and blow it on the sides now..!😁
Imagine if all you can was a pusher or a blade? where would you pile all that snow! With a snowblower being able to throw it a distance really helps
Fred, are you the only one in your neighborhood that has one of those bad boys and if so do they ask you to plow their driveways?
Yes I am the only one and I usually go for a ride with the tractor after cleaning my driveway and it happened a couple of times that some neighbors were shoveling. I then offered my help, its always a pleasure for me to help but I won't plow their driveway if they won't ask for it, some of them really enjoy doing it I dont want to steal this from them. 😁
Nice video and equipment. I rarely get enough snow to justify my similar blower, but nothing beats them in big dumps. FYI, you may want to just barely raise the blower off the ground while maneuvering between actually blowing snow. A severe angle on the pto shaft wears the universals significantly (like by a factor of 10 between 5 degrees and 20 degrees).
Thanks sir! I didn't know that about the PTO angle, thanks for the tip.
If you lower the skid shoes, then you wont throw as many stones.
Now that its icy and packed it doesn't happen anymore but yes I am lazy 😆
My Dad was stationed there during WW2. He was a armourer.
Thanks for his service
Nice job 💪. I don’t use a snowblower. What RPM you run at when using? Just curious, thanks 😊.
Thanks sir! For implements like my snowblower it must be 540 RPM, might be different for other implements but I am no expert.
Nice work Fred....What brand, size and model snow plow did you buy and did you buy it online or from a local dealer? I swapped out all 4 of my CK2610 cab work lights with LED's. Man it's like night and day. Pun intended. I got them off Amazon (New EXZEIT 4.4 Inch Led Work Light for Truck, 36W Flood Light Off Road Light Bar for Tractor Golf Cart UTV ATV, 12/24V) They were 28 bucks and easy to install with bullet connectors..
This is a 66 inches snowblower, brand is Ex-trac and model is "serie 20" for 20-30hp compact tractor. It has a 4 pale 14 inches rotor and yes I bought it from a local dealer. Thanks for all the details about your lights setup, upgrading all lights to LEDs (even turn and brake lights) is my next upgrade.
@@kioti-fred - I replaced the front headlights with LED's - (OXILAM H7 LED Bulbs Non-Polarity, 6500K Cool White 8 LED Chips No Dark Spot, 1:1 Design No Adapter Required, All-in-One Conversion Kit for Hi/Lo Beam Fog Lights Replacement, Pack of 2) - I tried to replace the front yellow blinkers and white lights to LED, but was having issues with getting the bulbs to connect in the sockets and went back to the original factory light bulbs - (1157 Led Bulb, 2057 2357 7528 BAY15D LED Bulbs for Back Up Reverse Light, Tail Light, Brake Light,Turn Signal Light, Pack of 2pcs Xenon White(6500K) (1157 LED Bulb, BAY15D 7528 2057 2357 LED Bulbs for Back Up Reverse Light, Tail Light, Brake Light,Turn Signal Light, Pack of 2pcs Amber Yellow) - The inside cab light was easy to change to LED - (AUXLIGHT DE3175 DE3021 DE3022 3175 31MM 1.22”Festoon Canbus Error Free LED Interior Light Bulbs 6000K Xenon White, Super Bright 6SMD Chips for Dome Map Door Courtesy License Plate Lights (Pack of 6) - I haven't tried the tail lights yet but its on my bucket list. I heard they're a sealed system. Let me know if you have any luck.
Very nice information thanks man! Its going to save me a lot of research time.
Nice job 💪
Thanks ✌
Hi kioti fred can you do a video on the chute movement. It dosent look like it has no hinge but pivot point and arms.
Sure, I will do it soon and let you know. Too cold outside these days!! -40c with wind chil!
@@kioti-fred of course. When ever the weather and time agrees. Thank you. I made my own articulated for closed quarters and around cars so they dont get plastered by rocks or ice.
Nice to see someone else using the same outfit I have . I never see my self cleaning my yard. Does youre cab window fogs?
Oh yes they do! really annoying... I have bought some anti-fog for windows a few days ago, hope its going to work. Tricks: clean your boots so they aren't full of snow, set your cab air intake to "fresh air" instead of "recyc" and turn down that hot air control to cold :)
@@kioti-fred yes i do all the above and it still does it. The only thing that seems to clear it is to put the ac on.
Will try that!! thanks
How's she goin'? Ya gotta love plowing at night. There is just something mesmerizing about it for me anyways!! Thanks for posting and take care!!
Yes, doing this at night is quite relaxing...I like it a lot! Thinking about swapping the work light for leds or adding a light bar.. there is always something to upgrade :D
@@kioti-fred The LEDs will make a big difference and they're easier on the alternator and tractor electrics too.
Harder on the wallet though!! I don't have 3k subscribers to pay for all this!! haha just kidding ;)
Pretty nice rig you got there! I like that snowblower! Just picked up a used Berco with electric chute since I don't have rear hydraulics and it's a huge improvement over manual crank.
Thanks sir! Couldn't agree more.. having complete control from the comfort of the cab is awesome..!
Great video. Did the rear hazard light come with the tractor, or was it a add on? I have the same tractor. Love that dran thing. Can't wait to get a few hours on it to make sure all is good and then ramp up the horse power to 40HP....
No, the hazard light did not come with it. I simply made a metal bracket and fixed a strobe bought from amazon to it, then passed a new wire through the cab post into the right wheel well. I soldered this cable to a rocker switch and tapped 12v into some cable (don't remember which one, I think it was the work lights 12v). I would love to ramp up hp on that motor too!! Just a little scared with warranty..!
@@kioti-fred Same here about the warranty. Great videos. Keep em coming..
Great job!
Thanks!
How's she goin'? The rear mounted blowers are some powerful eh. Hard on the back though. I installed a rear view camera and it helps a lot!! Lots of snow to clear but you have the gear to do it eh!! Take care!!
Yes that is hard on the back... I wouldn't be doing this as a full time job for sure!! Sometimes I wish I went with the front blower but couldn't justice 3 times the price..!
Great job!
Thanks sir!
Great 👍 content!
Glad you enjoyed it
Great machine thanks for sharing!
Thanks for watching!
Have a similar setup only the CK3510SEHC, goes through pretty much anything I would interested to know how you wired in the strobe light there is a wire harness but I have no idea where it goes or how to wire it up, enjoyed the video.
Mine did not have the wire harness, or I did not find it. I simply made a metal bracket and fixed the strobe to it, then passed a new wire through the cab post into the right wheel well. I soldered this cable to a rocker switch and tapped 12v into some cable (don't remember which one). It was fairly easy, I should have took pictures...! Good luck!
No 12v accessory socket in the cab???? Lots of these lights plug in.
Yes there is a 12v socket on top of the wheel well, but thats on the other side. Pretty sure I tapped 12v on the work lights wire.
Nice job. Looks like that tractor handles that blower good.
Yes it does, thanks sir!
I upload snow blowing videos to my channel, I found watching your tractor blow snow very relaxing great job impressive setup 😊
Thanks sir! I really like your videos too. I subscribed to your channel long time ago and almost bought a 3046r with a front blower because of you hehe
Nice job 💪
Thanks!
That CK2610 did really good, didn't even budge on the RPMS.
Yes! might not show on screen but that snow was packed and heavy. Ran it mostly on med gear and it performed really well. This tractor chew everything I threw at it hehe