Tools & Equipment - Proudly Aussie Owned Since 1976 🇦🇺
KINCROME is a proud Australian family-owned company with more than 30 years of experience in providing high-quality tools and equipment to the hardware, automotive & industrial markets.
SUBSCRIBE to keep up to date with all our latest tools and equipment launches, product demonstrations, how-to videos and everything in-between.
CONNECT with us:
Email - [email protected]
Website - www.kincrome.com.au/
Facebook - facebook.com/KINCROME/
Instagram - instagram.com/KINCROME/
Пікірлер
I bet this guy doesn’t know how to use those tools. Can’t even lubricate those bearings properly. 😂
Lyvo đẹp. Có từ thì OK
What a nicely done video 👏🏻
Is there power at the leads all the time? Like can I connect it to a 12v accessory to power it?
yes! it worked! Thank you Thank you. from Canada
Used it to attempt to undo the second 13 mm drain bolt tightened to 14 .5 ft/lbs as the first feed using a standard kinchrome socket but the second wouldn't which after numerous attempts finally rounded. I red a glowing review so bought these bolt extractors which were a tight fit so expected a successful result but it quickly rounded the bolt further. So a big fail
Worked fine - Thank you so much!
Good for fixing rims?
Can I have some
As soon as he said "our" I knew I couldn't trust him
And this is the technology we can expect in 2024 🙄 pathetic!
Pointless video. Wish companies actually showed you how to use their equipment.
Nope 😂 you can have incompatible grease tubes so the plunger will never work. Solution, ditch the cartridge and just fill the gun with grease instead.
Brand new jack wasn't working....thank you for saving me the cost of a new jack!
I bought the Kincrome ezi riv nut drill attachment, and kincrome rivet nuts. I could only manage to cause one rivet nut to collapse into shape. The rest just spin around and around on the drill. I am applying pressure, low rpm on Drill driver, and the hole is only just large enough for the rivet nut to fit inside. Useless tool. Doesnt work.
Man wish I found this video 2 hours earlier. So many so called tutorials not covering all the steps. Amazing job guys 🎉😊
So I bought it. It works well but I recommend either using vice or if you need to carry it in your caravan - buy a cheap 200mm “G” clamp. I had to use the G clamp as I couldn’t press hard enough for the grease to go thru.
Why not just make them with nm not ftp
How to know if it is dot 3 already or dot 4?? Lid says dot3/dot4
Same. My Kingchrome always stuck even after using the correct one. Frustrating. Is there a part I need to replace?
Your video is useless. It’s nothing but an advertisement. The title says it’s going to be a “how to” video. That is a lie. You didn’t even explain how it holds the transmission.
Bullsh…. Very difficult to grab the tail and then won’t spit out or release. Such a scam.
Great video, cheers
YAH YAH YAH YAH YAH, that's what your bogan accent sounds like. :( I don't want to be rude. :(
Typical shitcrome
There no mini fridge in it.
Crickey mate, perfect video.
My old (NOT Kincrome grease gun) recently stopped working and after 30 something years, I thought I deserved a new one. I have purchased the Kincrome K8058 gun and have put the partially used grease cartridge in the new gun. As far as I can tell, I have followed the instructions as shown on this video, but I can’t get the gun to prime. Should that work? Should I be able to use a partially used cartridge with no problems? Thanks.
It’s not King Crome it’s Kin Crome ffs and where are the 6 or 8 amp hour batteries
Quick and to the point....good on you bud. I was pushing the valve on top.
I have the same gun. Thought it was damaged...😆 🤣 thanks for the tip....works gr8. Cheers
Is it charging through the USB c port? Mine doesn’t seem to charge
I'm wondering if these sockets leave any noticeable marks on new bolt heads or nuts where the ribs in the sockets bite on to them? Are they good for everyday general use? Or mainly for stripped bolts etc?
Hi there, thanks for reaching out. We can confirm that the sockets do not leave any marks on the bolt heads or nuts! Thanks
@@kincrome great! Thanks for the reply. I'm in the market for a good set of these now. Thanks again
Thanks mate.
Thanks for the demonstration. It just helped me out this morning. First time using a rivet, got stuck on my first try, who do I turn to for rescue? KZread of course. Took the machine apart, took out the pin, reassembled and riveted away with no more issues.
Thank you sir
$600nzd for the drill & driver kit is crazy. Also, only 2ah batteries using the older Samsung cells. It’s just sad. Using your good name to pedal this crap. Just go with Dewalt or Milwaukee. Price is better and you know it works!
Gday, awesome episode, all the Polaris’s held up well considering the what they went through, I really enjoyed this one, cheers
I mean that's great but the opinion of these blokes means nothing. Want some reviews to come out tbh
Im guessing made in china?
Looks good. Many more tools in the pipeline for construction based trades.
Awesome
Looking forward to the impact driver
They look a lot like kobalt tools.
Wow! Wasn’t expecting this. Such good news.. can’t wait.
Great step by step video 🤟🏼
Bit late? By now I already have a shed full of other brand power tools and batteries. Love to buy one of yours, but then I need your batteries & charger too. Don’t have enough cash to replace the lot and you don’t have some of the power tools I have. I probably buy the corded heat gun to replace the cheap thing I have now.
This looks very interesting
Interesting… keen to see more on this
Keen as mustard on this new line up, wasn't expecting it either!
high quality production thank you for upload