Hello all :) This channel is dedicated to quad copters, drones, RC and other vehicles. There will be reviews, mods and upgrades along with LOS and FPV videos. More topics will be added as I grow and experience fun and interesting things to share with you. Please join me as I explore this awesome adventure! Hopefully I can help you in yours! I'm in it for bliss, hence the name. Thank you for joining me!
Пікірлер
Congrats!!! My next question is, how in the hell do you keep this thing so clean
Hey :) So I do something that's probably not initially good for the bearings although they are rubber sealed. First I take off the wheels and brush all the excess dust and dirt chunks off and use an electric blower (look up x power blower on Amazon). Then I take full strength simple green and spray the front and rear end and as close to the rear diff as possible without getting any on the motor. I never spray the electronics. Then while it's wet with simple green, I brush all of the areas, especially the shocks and drive shaft/ outdrive areas. I use a $12 long bristle paint brush from Home Depot to reach all those areas. Then I blast all that away with the electric blower until it's dry. I wipe the bottom and some of the top area with a cloth wet with simple green. Then I grab WD-40 and douse all of those areas liberally. Especially the output drives. I can go through a large can of WD within 2 races with two cars to clean. Okay, so with all that WD-40 dripping off, I set the car to drip on a flat surface (not tilted at all) and let sit for around 10 minutes or so. Then I hit all those areas again with the electric blower. Air compressors are ok but usually carry moisture in the tanks and if not using a moisture filter, will spray water mist on your car. Not good lol. So after the drip dry, I wipe it all down with that same rag and put in a carry bag. Later on when sitting around I take a micro fiber cloth dampened with simple green and wipe the whole inside area of the car. I use a wood or plastic pick with the cloth wrapped on the tip to get to the tough spots. Sometimes I even use q-tips lol. But that's my process :) I do the same for the tires/wheels minus the WD-40 of course lol.
how has this worked out? anything you would do differently or have done?
Hello, this has worked out very well. Never had a single ball end pop off. The adjustment notch is super easy to use and these results are for my 410SL and ET410.2. I even reached out to 1UP and let them know the turnbuckles are great. Gave them a link to this video too. I asked them about sponsorship and the told me to go apply lol. So no, I'm not sponsored by them. Only thing I want to mention is, even after prep drilling and greasing, they were still pretty tight and I still had to hold a rod end with long nose pliers to make adjustments on the turnbuckles. Not sure I would change that though. If drilled out too much, it might be too loose and end up pulling out or ripping threads in a bad crash. Thanks for watching, I appreciate the support!
I know life happens but really enjoyed watching your races, commentary, setup for your truck. I just bought a 2.0 kinda inspired by you (and many brands not making sct’s anymore lol)
Big thanks :) Yeah, good ol' real life kicking in and expensive to keep up with racing (competitively) when RL says hello lol. I'll be back racing though because it's just too much fun! My SL is ready to go.. just hangin' out in my little RC trailer. Maybe I'll look for a deal on a 2.0. I hear it's pretty tanky lol. I remember feeling more stability from the weight of my 410.3 which is still a good choice for a bigger track. Thank you very much for your support!
Too bad we can’t buy wheels or tires from dialed to support you. Very odd site and nothing for sct’s
Yeah, there was a recent change for 2024. The owner is not longer selling VP-Pro (just left over). He created his own tire line and it's made in the USA but so far only 1/8 buggy and I think 1/8 truggy coming soon. I appreciate you watching though. I'll get more content up soon :)
dialed rc
The wheelbase becomes 3mm longer than longest setting with the hubs spaced all the way forward. How did that change play in to handling?
Hi, yes it felt more stable this way overall. This track is on the bigger side for this class so the turns aren't super tight. Shocks forward definitely turns tighter but on a dusty blown out corner, it caused more spin outs. The shocks to the rear minimized this. If I was racing indoors and on a smaller track, I would have kept the shocks in stock position. Btw, I did the same on my SCT410SL and got the same results. Oh, and overall more stability with shocks to the rear especially through ruts and recovering bad landings. Thanks for watching and sorry for the late reply.
0:45 Dude almost got smoked.
what front and rear springs are you using?
Front TKR7044: www.amainhobbies.com/tekno-rc-50mm-front-shock-spring-set-orange-2-5.75lbin-tkr7044/p1245056?gad_source=1&gclid=Cj0KCQjwn7mwBhCiARIsAGoxjaLBVLeXT1b9uM8AxCseRpWN0J_Vx9ljUX-OsK4YsILWYx3MsS1o_RAaAh8aEALw_wcB Rear TKR7246: www.amainhobbies.com/tekno-rc-63mm-rear-shock-spring-set-1.3x9.375-orange-3.01lb-in-tkr7246/p788353
Shame they don't come at 17mm 0 offset.
Can you tell me the ball an ball cup ends you used?
Here's all the info from one of my other videos: kzread.info/dash/bejne/imeVsKqchLzfY5c.htmlsi=bjWWhC5CFtgNu16d
Also, the ball ends I used are the stock ones from the kit.
Hey Coral Springs track I live 1.5 hrs away from there. Much love from Port St. Lucie!!
Nice! Come race with us sometime :)
Hello. What size pinion? Spur? My kit is on the way. I got. 5.5 motor too. Nice set up.
Thanks! I'm using the stock spur gear and 18T pinion.
Thank you
How does a person decide what motor turn/ kv to buy for modified racing?
Best thing for this is to talk to the people at the track you'll be going to. In general though, the higher kv smaller size motors like 3300 up to 4600 go well with 2s (electric 4wd short course). The larger motors with lower kv 1800 to 2200 usually go with 4s 1/8 ebuggies. For this lightweight 410SL, a 5.5T to 6.5T on 2s would work. But ya, it really depends on the class and the track. I think I won 9 or 10 races in a row with my 410SL on a 6.5T Reedy on 2s.
What is the difference between Striker Evo and Gripz Evo tires?
Hi, thanks for watching! Check out the 40 second mark in my video below. The only difference is the tread pattern. At my track I like the Gripz all around but the Striker seems better in loose or loamy conditions. kzread.info/dash/bejne/pZp9k9alqNSppag.htmlsi=xD1Gd4Jf2gHOUxa2
Dante, just purchase this sct, can you relay your setup sheet
Hi, thanks for watching, try this link to my setup sheet. I may have to approve to view first though. drive.google.com/file/d/10f5W941u8f-Htv9JaSMLciqCa3nkxWvI/[email protected]&sharingaction=manageaccess&role=writer&ts=650e217a
Thanks for the tip
Congratulations bro 👏
Pure BS that Tekno doesn't include all these upgrades in the kit. Other manufactures do!! It's ridiculous to spend $450 on a kit and have to sink another $200+ to make it durable. Yes, the platform is fast but not durable as a kit.
I hear ya there.. It's a very expensive kit and should be near bulletproof for $450. I heard a lot about rear bulkheads breaking. Something tells me the rear bumper mod I did kept some pressure off it. I'm still running the original bulkhead and had many races with some really bad crashes.
What bit holder do you have on the deealt screw driver?
Hi, thanks for watching, I got the from Amazon. BitGripper v2 Variations a.co/d/bNQwPh1
absolutely awesome race
Thank you!
my god what a melee.
I use crc electronics cleaner sprayed in a bottle and i just throw all the small parts in and shake it up. It works like a charm
what car are you diving?
Hi Carlos, I wasn't in this race but for 1/8 ebuggy I drive for Sworkz. The S35-4E.
do you have a setup sheet youncan share
Hi, there's a link to my setup in the description of this video. Thanks for watching!
can't access it, sent a request
@@CarlosDelaoGunEngraver I'm sorry.. Really not sure why the link is doing that. Here it is on the 410SL fb group. m.facebook.com/groups/1189817885233005/permalink/1258668161681310/?mibextid=9R9pXO
Please What is the off set of VP pro tires for Taking SCT sl?
I'm not sure exactly what the offset is but it's the same as the Tekno RC SCT wheel. If you can find out the offset of the Tekno wheel, that will be the offset.
Dialed rc hobbies
I'm hoping the winner, Jeff Jones responds today by 10pm. I haven't seen a comment or received an email yet.
Congratulations!
That would be my biggest fear as a marshal..to flip a lapped driver and wreck a lead driver in the process
Congrats Jeff and thanks for the raffle. Looking into a set of those tires now.
Hello all, I plan to do the video tomorrow (Tuesday) to pick the winner! Hope everyone is having a great Labor Day!
Dialed rc hobbies!
Dialed-RC Hobbies Can't wait
Dialed-RC Hobbies 4wd SC is the best racing class. :)
Dialed-RC Hobbies
Dialed-Rc Hobbies
Dialed-Rc Hobbies. Glad to see your still doing well. 😊
Dialed-Rc Hobbies!
Dialed Rc Hobbies
Dialed-RC Hobbies. Thanks for the info, going to check out their site now.
Dialed-RC Hobbies
Dialed-RC Hobbies, Congrats on almost 1,000 subscribers! Good luck to all!
Dialed-RC Hobbies!!!
Congrats on reaching 800 subs ! Enter me as well, thank you for the opportunity Dialed-RC Hobbies
Dialed-RC Hobbies
Dialed-RC Hobbies! Thanks for doing a giveaway. Can always use as new set of SCT wheels for the track.
DIALED-RC HOBBIES
Dialed-RC Hobbies
Dialed-RC Hobbies
DIALED-RC HOBBIES