Where was the gas leak coming from I’m having this same problem now
@misterw01f237 ай бұрын
I do remember that the gas pump was cracked on top. There was a little puddle of gas of top of the gas pump unit. But we couldn’t see it at all until we pulled down the gas tank and found out that the gas pump unit was cracked and leaking
@tr4ilblazin7 ай бұрын
@@misterw01f23 okay thanks bro
@compallitoscott65959 ай бұрын
Good job thank you for the video guys 👍
@cestpasakramjunior Жыл бұрын
Hi! Can I include this video in my new compilation? In the description I will put the link to Your channel, while the name of your channel will be put in the compilation. :)
@user-nu6ro6fu1x Жыл бұрын
Thank you for the video i have a question that new pads are thicker than used ones. how did you put two pads in without pushing brake piston back Only steel stick moving can do that? i'm wondering if there's no damage to disk router
@misterw01f23 Жыл бұрын
I did push the piston back. I show it 2:45 in video. Hopefully this helps👍🏼
@frontlinecars20yroldfinds78 Жыл бұрын
kzread.info/dash/bejne/q4unspiih9HUpNY.html
@frontlinecars20yroldfinds78 Жыл бұрын
I broke the clips now what new lines? Clips from fuel filter
@frontlinecars20yroldfinds78 Жыл бұрын
Big Frontline612 stopN thru Minnesota bound 💯
@knighttaylor4272 Жыл бұрын
thank you saving me lots of time
@mycadi942 жыл бұрын
Shortly after installing new brake pads all around, resurfacing all my rotors I got a "CHECK SERVICE" indicator light on, is that pretty common ?
@nunyabusiness33642 жыл бұрын
Fast trick to change a fuel pump sports Trac without taking the tank down and draining just take the bed off 4 bolts and filler lines off the tank Twice's easy
@knighttaylor4272 Жыл бұрын
bruh fuckin genius
@texasham75552 жыл бұрын
Thanks a bunch. The 12mm bolt was the hidden gem in this video. I’ve changed brakes before but not on this GS430 I have now. I have a slow fluid leak somewhere. I think it’s somewhere near the master cylinder. Any places that you might expect a leak might occur?? I’ll probably bleed the brakes just because I’ve had this leak. Hopefully I can find it. Thanks
@callmebackfriday22 жыл бұрын
Does most molding based on measure from bottom of the door and then go up xx (i.e. 11 inches) inches equally? I have a 2009 Corolla and the door, window, front wheel, rear wheel are not same height. The other way may be measure from door handle down xx inches. I try to make the molding flow with the car. Thanks for the video.
@samuelgarcia21532 жыл бұрын
Porque le cambio la pompa de gas y no quiere ensender
@nestornoria11222 жыл бұрын
where is the fuel regulator , everyone tell me is in the fuel tank but i dont see...
@bblair5022 жыл бұрын
Good information! You seem to be one of the only mechanics showing this that know what the 12mm holes are for in the rotor! Most others use a big hammer to beat the cr@p out of the rotor until it falls off....
@misterw01f232 жыл бұрын
Thanks alot. Gotta work smarter not harder haha
@desireevazquez12792 жыл бұрын
Wow your so talented 😍
@Acsanchez33762 жыл бұрын
Chaleeee se ve muy facil pero no me animo solo
@darwinpalmer77532 жыл бұрын
My timing chain tensioner on the passenger side had extended all the way out killing the my 02 sport trac, have replaced the tensioner as well as alternator,crankshaft sensor, coil pack, plugs and wires and last but not least downstream 02 sensor, it will crank but not start, any advice?
@chevoaguillon65836 ай бұрын
Fuel pump
@sufilms88782 жыл бұрын
Hello, is it OK to feature this in a compilation? You will be fully credited.
@daphnewilliams79023 жыл бұрын
Hello! How many inches from the bottom of the door if you're installing the moldings on a 2021 RX350 F Sport?
@brucetec65973 жыл бұрын
Lol all these years I've been removing the clips. Learned something new.
@samaelperveg56073 жыл бұрын
Tanks, saludos desde MEXICO
@misterw01f233 жыл бұрын
De nada, y saludos 🤙🏼
@pollydor073 жыл бұрын
Thanks
@IglooCrewGearshiftMedia3 жыл бұрын
Hi there, would it be okay if I we're to use this video in a driving clip compilation I'm making? Ill give full credit in the description of the video. thanks in advance!
@misterw01f233 жыл бұрын
Thats fine
@nickhines11313 жыл бұрын
How much were those?
@JesusHernandez-jt4uf3 жыл бұрын
Thanks bro. For taking the time and effort to help us out. I'll do it myself, we have a car similar to your's so great vid!!!
@misterw01f233 жыл бұрын
No problem!
@rickysvt3 жыл бұрын
Great video, I'm looking into buying a ES that has these moldings but I don't like these moldings. Would removing damage the paint? How difficult is the removal?
@misterw01f233 жыл бұрын
It shouldn’t but u do have to take ur time removing it tho and using adhesive removal. U have to pry on the molding little by little. And use a plastic panel popper so it wont scratch the paint
@inspex_4463 жыл бұрын
Do you have the links for the rotors/pads you used on this video?
@misterw01f233 жыл бұрын
I do not, but they are factory rotors and pads which i got from a Lexus Dealership
@murraymoss26953 жыл бұрын
I like your attention to detail. like removing the rust off the hub. Good Skills, Thank you
@archibaldnicholson97923 жыл бұрын
How to install rx350 doormolding
@bubulububulubu50283 жыл бұрын
Go up !
@aldringuzman6643 жыл бұрын
Do you need to bleed the brakes?
@misterw01f233 жыл бұрын
No you don’t
@aldringuzman6643 жыл бұрын
@@misterw01f23 ok thank you. I will be replacing them this weekend. Was aittle confused about the bleeding process because there's so many different answers to it. But your video will be my guide thank you so much
@misterw01f233 жыл бұрын
@@aldringuzman664 best of luck man. It should be straight forward to replace.....however, do expect some brake fluid to come out from the brake reservoir when your pushing the caliper pistons back. Don’t freak out it’s normal however if you want to avoid that, suck some brake fluid out from the brake reservoir like 1/4 if its on “Full” level with a fluid extractor if you have one. But if its already below the full level line you should be fine, just add some brake fluid after you are done with the brake job n after you have pumped the brake pedal a couple of time. Then add the brake fluid to the proper level and you’re all set
@oscarlavista76773 жыл бұрын
disconnect negative battery terminal first.
@jseidl213 жыл бұрын
awesome video thank you - gs450h owner
@greenhavennn3 жыл бұрын
Thanks for the install video. You mentioned that you might edit video to include a couple of things you forgot to mention. If you edit the the video, would you please show us the actual installation method you use for putting the molding in place and removing the adhesive backing at the same time. I think that's what worries most first time installers. Watching you actually removing adhesive backing and putting molding in place would be key to a proper installation. Thank you.
@misterw01f233 жыл бұрын
Honestly what we would use is a clean rag, 3M General Purpose Adhesive Cleaner and a plastic panel popper that I showed in the video when leveling the panels....when you remove old panels or damage panels just spray adhesive remover on the double sided tape and use a plastic surface to remove it. Dont put alot of pressure because u dont want to damage the paint but once u remove most of the big parts of the tape then spray the clean rag with 3M adhesive remover and go over the surface u want clean n it should remove everything. Then wash the area with soup n water and u should be fine for installation
@misterw01f233 жыл бұрын
Sorry for not adding that in the video
@jaimecabrera28363 жыл бұрын
Stop saying you know bruuhh because i don't know that's why im watching your video😬
@misterw01f233 жыл бұрын
I feel u man haha
@ChaseGaming_23 жыл бұрын
Let's gooo baby! What a game!!
@misterw01f233 жыл бұрын
🔥🔥🔥🔥
@desireevazquez12793 жыл бұрын
❤️❤️❤️❤️❤️ yassssssss❤️❤️❤️❤️❤️
@jeffreyrouse38673 жыл бұрын
You don't have to remove the gas tank , take out 4 bolts in the bed and slide it back about two feet and you can get to it from the top . Easy job than can be done in less than an hour .
@bubulububulubu50283 жыл бұрын
Ja ja ja you soun realy , I daun the tank too
@garciafamily5850 Жыл бұрын
Nope not on this truck it has to be dropped.
@garciafamily5850 Жыл бұрын
Fuel pump is located under rear driver side passenger seat. If you remove bed you will not be able to get to it.
@rickbrando1293 жыл бұрын
the only thing i would have done different is use a floor jack to hold the tank while removing the straps and then to hold it in place for installing.
@vanhau29943 жыл бұрын
HOT SEX 18+
@everespinoza833 жыл бұрын
Alguien sabe si es el mismo proceso en una 2005 ?
@pedromares573 жыл бұрын
X2
@colotlanvega3 жыл бұрын
Pienso que es el mismo proceso pero alguien sugirió aflojar la caja y hacer el remplazo por arriba, suena más fácil. Es lo que quiero hacer con la mía y es 05 también
@everespinoza833 жыл бұрын
@@colotlanvega lo hice como en el vídeo batalle un poco pero si quedo bien
@colotlanvega3 жыл бұрын
@@everespinoza83 que bien, usaste parte original o aftermarket? Busco la original pero no la encuentro. Saludos
@everespinoza833 жыл бұрын
@@colotlanvega compré en AutoZone espero q salga bien
@DashcamLive3 жыл бұрын
Hi! Is that alright if I feature this clip in my next video? Fully credited!
@misterw01f233 жыл бұрын
That’s fine
@davidivanez61383 жыл бұрын
Cuántas cadena de tiempo tiene
@sky13eyaj123 жыл бұрын
Just curious toyota/lexus typically use metric for their measurements with very specific measurementsfor the molding..but you're using inches.
@misterw01f233 жыл бұрын
Im using inches so it can be easier for u guys to understand.....i converted all the measurements into inches
@greenhavennn3 жыл бұрын
@@misterw01f23 THANK YOU for using US measurements. Metric sucks for those not used to it.
@artthi79183 жыл бұрын
Good tip on the panel popper! Right @ 6:27 or so.
@brandonhuggins19493 жыл бұрын
What was the reason for changing your fuel pump?
@misterw01f233 жыл бұрын
The truck suddenly turned off while driving and then it wouldn’t turn on again
@Jonathan_DC3 жыл бұрын
Was it the 4-pin (3L2Z-9H307-EC) or 7-pin (2L2Z-9H307-Hx) connector fuel pump? I ask because the 4-pin 2L2Z was discontinued and updated to the 3L2Z 7-pin giving us “does not fit” when searching online through our VINs showing conflicting OEM part numbers for our 2002 MYs. There are a few sites still selling the 4-pins; just wanted to get your thoughts-
Пікірлер
That's painters tape bro! Not duct tape.
Where was the gas leak coming from I’m having this same problem now
I do remember that the gas pump was cracked on top. There was a little puddle of gas of top of the gas pump unit. But we couldn’t see it at all until we pulled down the gas tank and found out that the gas pump unit was cracked and leaking
@@misterw01f23 okay thanks bro
Good job thank you for the video guys 👍
Hi! Can I include this video in my new compilation? In the description I will put the link to Your channel, while the name of your channel will be put in the compilation. :)
Thank you for the video i have a question that new pads are thicker than used ones. how did you put two pads in without pushing brake piston back Only steel stick moving can do that? i'm wondering if there's no damage to disk router
I did push the piston back. I show it 2:45 in video. Hopefully this helps👍🏼
kzread.info/dash/bejne/q4unspiih9HUpNY.html
I broke the clips now what new lines? Clips from fuel filter
Big Frontline612 stopN thru Minnesota bound 💯
thank you saving me lots of time
Shortly after installing new brake pads all around, resurfacing all my rotors I got a "CHECK SERVICE" indicator light on, is that pretty common ?
Fast trick to change a fuel pump sports Trac without taking the tank down and draining just take the bed off 4 bolts and filler lines off the tank Twice's easy
bruh fuckin genius
Thanks a bunch. The 12mm bolt was the hidden gem in this video. I’ve changed brakes before but not on this GS430 I have now. I have a slow fluid leak somewhere. I think it’s somewhere near the master cylinder. Any places that you might expect a leak might occur?? I’ll probably bleed the brakes just because I’ve had this leak. Hopefully I can find it. Thanks
Does most molding based on measure from bottom of the door and then go up xx (i.e. 11 inches) inches equally? I have a 2009 Corolla and the door, window, front wheel, rear wheel are not same height. The other way may be measure from door handle down xx inches. I try to make the molding flow with the car. Thanks for the video.
Porque le cambio la pompa de gas y no quiere ensender
where is the fuel regulator , everyone tell me is in the fuel tank but i dont see...
Good information! You seem to be one of the only mechanics showing this that know what the 12mm holes are for in the rotor! Most others use a big hammer to beat the cr@p out of the rotor until it falls off....
Thanks alot. Gotta work smarter not harder haha
Wow your so talented 😍
Chaleeee se ve muy facil pero no me animo solo
My timing chain tensioner on the passenger side had extended all the way out killing the my 02 sport trac, have replaced the tensioner as well as alternator,crankshaft sensor, coil pack, plugs and wires and last but not least downstream 02 sensor, it will crank but not start, any advice?
Fuel pump
Hello, is it OK to feature this in a compilation? You will be fully credited.
Hello! How many inches from the bottom of the door if you're installing the moldings on a 2021 RX350 F Sport?
Lol all these years I've been removing the clips. Learned something new.
Tanks, saludos desde MEXICO
De nada, y saludos 🤙🏼
Thanks
Hi there, would it be okay if I we're to use this video in a driving clip compilation I'm making? Ill give full credit in the description of the video. thanks in advance!
Thats fine
How much were those?
Thanks bro. For taking the time and effort to help us out. I'll do it myself, we have a car similar to your's so great vid!!!
No problem!
Great video, I'm looking into buying a ES that has these moldings but I don't like these moldings. Would removing damage the paint? How difficult is the removal?
It shouldn’t but u do have to take ur time removing it tho and using adhesive removal. U have to pry on the molding little by little. And use a plastic panel popper so it wont scratch the paint
Do you have the links for the rotors/pads you used on this video?
I do not, but they are factory rotors and pads which i got from a Lexus Dealership
I like your attention to detail. like removing the rust off the hub. Good Skills, Thank you
How to install rx350 doormolding
Go up !
Do you need to bleed the brakes?
No you don’t
@@misterw01f23 ok thank you. I will be replacing them this weekend. Was aittle confused about the bleeding process because there's so many different answers to it. But your video will be my guide thank you so much
@@aldringuzman664 best of luck man. It should be straight forward to replace.....however, do expect some brake fluid to come out from the brake reservoir when your pushing the caliper pistons back. Don’t freak out it’s normal however if you want to avoid that, suck some brake fluid out from the brake reservoir like 1/4 if its on “Full” level with a fluid extractor if you have one. But if its already below the full level line you should be fine, just add some brake fluid after you are done with the brake job n after you have pumped the brake pedal a couple of time. Then add the brake fluid to the proper level and you’re all set
disconnect negative battery terminal first.
awesome video thank you - gs450h owner
Thanks for the install video. You mentioned that you might edit video to include a couple of things you forgot to mention. If you edit the the video, would you please show us the actual installation method you use for putting the molding in place and removing the adhesive backing at the same time. I think that's what worries most first time installers. Watching you actually removing adhesive backing and putting molding in place would be key to a proper installation. Thank you.
Honestly what we would use is a clean rag, 3M General Purpose Adhesive Cleaner and a plastic panel popper that I showed in the video when leveling the panels....when you remove old panels or damage panels just spray adhesive remover on the double sided tape and use a plastic surface to remove it. Dont put alot of pressure because u dont want to damage the paint but once u remove most of the big parts of the tape then spray the clean rag with 3M adhesive remover and go over the surface u want clean n it should remove everything. Then wash the area with soup n water and u should be fine for installation
Sorry for not adding that in the video
Stop saying you know bruuhh because i don't know that's why im watching your video😬
I feel u man haha
Let's gooo baby! What a game!!
🔥🔥🔥🔥
❤️❤️❤️❤️❤️ yassssssss❤️❤️❤️❤️❤️
You don't have to remove the gas tank , take out 4 bolts in the bed and slide it back about two feet and you can get to it from the top . Easy job than can be done in less than an hour .
Ja ja ja you soun realy , I daun the tank too
Nope not on this truck it has to be dropped.
Fuel pump is located under rear driver side passenger seat. If you remove bed you will not be able to get to it.
the only thing i would have done different is use a floor jack to hold the tank while removing the straps and then to hold it in place for installing.
HOT SEX 18+
Alguien sabe si es el mismo proceso en una 2005 ?
X2
Pienso que es el mismo proceso pero alguien sugirió aflojar la caja y hacer el remplazo por arriba, suena más fácil. Es lo que quiero hacer con la mía y es 05 también
@@colotlanvega lo hice como en el vídeo batalle un poco pero si quedo bien
@@everespinoza83 que bien, usaste parte original o aftermarket? Busco la original pero no la encuentro. Saludos
@@colotlanvega compré en AutoZone espero q salga bien
Hi! Is that alright if I feature this clip in my next video? Fully credited!
That’s fine
Cuántas cadena de tiempo tiene
Just curious toyota/lexus typically use metric for their measurements with very specific measurementsfor the molding..but you're using inches.
Im using inches so it can be easier for u guys to understand.....i converted all the measurements into inches
@@misterw01f23 THANK YOU for using US measurements. Metric sucks for those not used to it.
Good tip on the panel popper! Right @ 6:27 or so.
What was the reason for changing your fuel pump?
The truck suddenly turned off while driving and then it wouldn’t turn on again
Was it the 4-pin (3L2Z-9H307-EC) or 7-pin (2L2Z-9H307-Hx) connector fuel pump? I ask because the 4-pin 2L2Z was discontinued and updated to the 3L2Z 7-pin giving us “does not fit” when searching online through our VINs showing conflicting OEM part numbers for our 2002 MYs. There are a few sites still selling the 4-pins; just wanted to get your thoughts-
I put a trap door in my bed just for that