very good explanation,make some more videos like on solid combustion also
@whisler5.016 күн бұрын
I did all the steps, but when I went to contact region it only showed one tube in blue, and not the whole tubing in red like yours. How do I fix that?
@KamaleshKarthika-qh2zp18 күн бұрын
Thank you so much sir 🙏
@akankshagupta20523 күн бұрын
When i m trying to import the structure from catia to ansys its showing error that " the selected file is of an unsupported or unfigured geometry type" . How to solve this error? Can u plzz help me with this ?
@MechTechSimulations21 күн бұрын
If you want to import geometry from other modeling software, you need to do CAD Configuration. kzread.info/dash/bejne/i5OFucmniJjJk6g.html
@akankshagupta20521 күн бұрын
@@MechTechSimulations i m facing issue while doing meshing. Can u help me out with this ?
how if I want to simulate the undershot turbine? what do I need to do in order to simulate the blade which in contact with water?
@MechTechSimulationsАй бұрын
Nothing else, just change the fluid to 'liquid water' under the cell zone conditions.
@limchinchen7988Ай бұрын
I’m using solidworks to draw the turbine and then import into ansys. Then I follow ur step to do but can’t. I create the enclosure but it show an error (operation would result in non-manifold bodies).
@limchinchen7988Ай бұрын
If I create the cylinder and box through 1) click icon “create” 2) choose icon “primitives” Is this same as enclosure u do in this video?
@limchinchen7988Ай бұрын
And also my turbine is not fully immersed in water, can I make an enclosure cover half of the turbine?
@MechTechSimulations26 күн бұрын
But a combination of 3D, Transient and Multiphase is really challenging and needs a heavy computational power.
@frq3155Ай бұрын
There is a shortcut, in 4:10 you can factor the (-1+λ) into the expression (1-λ)(1-3λ+λ^2) -1+λ = 0 (1-λ)(1-3λ+λ^2) - (1-λ) = 0 (1-λ)(1-3λ+λ^2-1) = 0 (1-λ)(λ^2-3λ) = 0 That way, the three eigenvalues can be found momentarily and there is no need to solve a cubic equation and perform long division.
@user-hs4dr7tg1uАй бұрын
thank you
@MechTechSimulationsАй бұрын
You're welcome
@indranilghosh56Ай бұрын
Can tell me the "methods" used
@MechTechSimulationsАй бұрын
I hope all the methods and details are included in the video. Can you please elaborate on what you mean?
Sir w there is 2nd diagram also there in which one edge is parallel to base that diagram also correct sir for this question
@MechTechSimulations2 ай бұрын
Sorry, I didn't understand your point. Can you please specify the time in the video where you have this question?
@Hitu6192 ай бұрын
@@MechTechSimulations diagram sir hexagon
@QuantumBeatsLab2 ай бұрын
what is the formula to calculate the mass flow rate in channel flow over cylinder in 2 dimension? Please reply
@QuantumBeatsLab2 ай бұрын
do I need to consider the cross sectional area in case of a 2D contour?
@MechTechSimulations2 ай бұрын
If that is a cylinder, we need to select axisymmetric instead of planar in Fluent's general settings. In 2D simulations, the mass flow rate is computed and reported in Fluent by considering the third axis as 1m by default. You can change this in the reference values if you have the third axis dimension.
@user-lv3qk9sj2g2 ай бұрын
Thank you I am finding this question answer Tomorrow is my exam it help me alot❤❤❤❤
@MechTechSimulations2 ай бұрын
Most welcome 😊
@Hitu6192 ай бұрын
Brilliance smart work 😮😮
@MechTechSimulations2 ай бұрын
Thank u for your appreciation!
@dihanshalindra48162 ай бұрын
Hey sir how can we generate a video for the above solutions without saving the photos
@MechTechSimulations2 ай бұрын
Try setting up phase contours in Graphics and Animations, then create and define a Solution Animation under Calculation Activities. Preview and save the animation as a video by clicking Write/Record.
@yusufmertdeprem31392 ай бұрын
Hello sir, I'm making all the things same but my program gives me floating point error, what can I do about it? I tried to smaller and bigger mash sizes but it didnt solve.
@MechTechSimulations2 ай бұрын
Try without the acceleration, so we can determine whether the problem is with the acceleration or something else..
@yusufmertdeprem31392 ай бұрын
@@MechTechSimulations I runned again without acceleration and it didnt give error, tried again with linear acceleration and it gave an float error message again
@yusufmertdeprem31392 ай бұрын
@@MechTechSimulations I tried without acceleration and it didnt give float error message. When I add acceleration it gives error whatever its linear or time related. And for extra information ım trying to work on 3D tanks.
@baruahsarthak_2 ай бұрын
Crisp and to the point.
@MechTechSimulations2 ай бұрын
Thank you for the appreciation...
@PeterGuite12 ай бұрын
I think we can directly use spectral theorem for symmetric matrix/self adjoint operators
@AnkushBhoye-hu9lx2 ай бұрын
OK sir
@hardikpawar27862 ай бұрын
Thank you sir
@MechTechSimulations2 ай бұрын
Welcome
@wardiaaitamrane63962 ай бұрын
Hello would you tell me how much the température is about in the exit of the collector?
@MechTechSimulations2 ай бұрын
Here are the steps to obtain the pressure at the outlet: Go to Reports, then Surface Integrals, select Average, followed by Average of Pressure. Choose the outlet boundary and click on Print. This will provide you with the average pressure at the outlet.
@wardiaaitamrane63962 ай бұрын
@@MechTechSimulations thank you for the help i will try later
@okeetoroma2 ай бұрын
Nicely explained. Thank you
@MechTechSimulations2 ай бұрын
You are welcome
@hastinrhenius1932 ай бұрын
Beautiful explannation sir tysm strainght to the point
@MechTechSimulations2 ай бұрын
You're most welcome
@ahmadali55082 ай бұрын
Hats off to the teacher !!! Great and conceptual teaching.
@MechTechSimulations2 ай бұрын
Thanks a lot
@alb83502 ай бұрын
Hi, How can I run a long transient simulation with solar ray tracing? Regards
@MechTechSimulations2 ай бұрын
You need to activate the DO radiation model and proceed with proper transient settings, such as timestep size and number of timesteps
@alb83502 ай бұрын
Do you mean that a solar load calculation only activating solar calculator does not allow to do simulations for more than 24h?
@Abu_Crush_15232 ай бұрын
What you are drawing is not visible instruction not clear i got red fort
@MechTechSimulations2 ай бұрын
Sorry... Will ensure proper visibility in upcoming videos...
@javierpascualenaferre89962 ай бұрын
Hi, Im doing a final project research and I would like to obtain the thermal conductivity of the material of the heat generation. Appreciate it 🙏
@MechTechSimulations2 ай бұрын
Unfortunately, as far as I know, ANSYS cannot calculate thermal conductivity on its own. Instead, we must input the thermal conductivity value obtained from experimental data or reliable sources like material databases. However, once we provide the thermal conductivity along with the heat generation rate, ANSYS can generate temperature distribution results across the entire domain.
@zaraadamson68033 ай бұрын
Please do an updated one for Ansys 2024 Student version if possible, thank you so much for this video.
@MechTechSimulations2 ай бұрын
Thank you so much for your kind words. I was actually considering creating videos with the latest versions already, so your reminder is greatly appreciated. I'll get to it soon.
@EVAPOEEPE3 ай бұрын
nice video,thanks for sharing BTW if anyone need encapsulate solution please kindly let me know😊😊
@MegaKhan19683 ай бұрын
Thanks for this example. I thought K-E cannot be used for the vortex shedding analysis and only LES or DES should be used. I need to run a case for vibration analyis and need to know the flucutatyion of the pressure the frequency. Could you explain if K-E can be used. As far as I remember only LES results can be used for the FFT etc.
@MechTechSimulations2 ай бұрын
Actually, it's my attempt to compute the frequency of flow-induced vibration. However, as you mentioned, there will definitely be differences between turbulence models. I've explored this in the video linked below. kzread.info/dash/bejne/lIt_17ChaKqYeaw.html
@OluwasegunOgundele-qx6vl3 ай бұрын
how can i delete a face, i want the top be open.....when i used the create and delete option it distorted the model
@MechTechSimulations2 ай бұрын
Sorry for the delayed reply. You can simply set up a pressure outlet boundary condition on that surface if you only need an opening and want to monitor variables within the domain. However, if you're also interested in understanding what happens beyond the outlet, you'll need to extend the fluid domain outside as well.
@jorgegodoy68243 ай бұрын
If that does not work because your model is not watertight you can do it on Ansys Discovery tool
@MechTechSimulations2 ай бұрын
Yep, I'm on a exploration mission! Although, I might be late to the party of discovery...
@sarahhassan49533 ай бұрын
U SAVED ME!!! God bless you
@MechTechSimulations3 ай бұрын
Thank you so much. May God bless you too...
@The_Voice_of_Reason7483 ай бұрын
Beautiful presentation. Straight to the point. No nonsense.
@MechTechSimulations3 ай бұрын
Thank you for your appreciation
@vighneshjangle5663 ай бұрын
Thank you sir for your wonderful explanation ❤
@MechTechSimulations3 ай бұрын
You are most welcome
@brucewayne62573 ай бұрын
Thank you mam
@MechTechSimulations3 ай бұрын
Most welcome 😊
@michexf93853 ай бұрын
Excellent Explanation
@MechTechSimulations3 ай бұрын
Glad you liked it
@p.arivukkanalpandiyan41433 ай бұрын
thank you
@MechTechSimulations3 ай бұрын
You're welcome
@bhoopendrapandey7873 ай бұрын
Thank you for making this lecture very interesting and interactive. I would appreciate it if you would share the PPT also.
@selvamurugan62583 ай бұрын
Kindly share link for geometry please because description link won't open.
@MechTechSimulations3 ай бұрын
Sorry, I hadn't noticed that the link is broken. Please email me at [email protected] or visit mechtechsimulations.com now
@sreeharivm5494 ай бұрын
Sir how to modify trailing edge and find cl cd value of different angle of attack.
@MechTechSimulations3 ай бұрын
We can do that in two ways. One is at the geometry level by providing a certain angle with horizontal or vertical reference. The next one is body transformation
@derrickbecker98564 ай бұрын
Why doesnt this equal the drag force equation?
@MechTechSimulations3 ай бұрын
Dear Becker.. The equation for the force exerted by a jet on a plate is derived from the momentum equation, is specific to the interaction between the jet and the plate, considering factors such as the angle of incidence and the change in momentum of the fluid. On the other hand, the drag force equation is more general and applicable to various shapes moving through a fluid, incorporating a "drag coefficient" to account for the shape and characteristics of the object. Therefore, while both equations involve forces in fluid mechanics, they address different scenarios and considerations.
@syaduddingrr31544 ай бұрын
very helpful!!! i was searching how to rotate than i find you
@MechTechSimulations4 ай бұрын
Glad it helped!
@tomass64324 ай бұрын
Thank you
@MechTechSimulations4 ай бұрын
You're welcome
@user-mg4vk2mz8p4 ай бұрын
Thanks a lot for the video, it was really helpful. However when I want to mesh it it says that it can`t be done for some problems. I have delated the solid part and it still says that there are problems with the mesh. Any idea about how I can do it ?
@MechTechSimulations2 ай бұрын
Really sorry for the late reply. Have you managed to tackle it? If not, could you share some screenshots of the error? I'll take a look and see what's up...
@saddamislam99004 ай бұрын
sir at 2:13 min how can you bring the coordinate system like X, Y, Z component at left of workspace ?
@MechTechSimulations2 ай бұрын
Actually, at that time, I hadn't done anything yet. I simply created the initial geometry with the origin, so it's just sitting there...
Пікірлер
very good explanation,make some more videos like on solid combustion also
I did all the steps, but when I went to contact region it only showed one tube in blue, and not the whole tubing in red like yours. How do I fix that?
Thank you so much sir 🙏
When i m trying to import the structure from catia to ansys its showing error that " the selected file is of an unsupported or unfigured geometry type" . How to solve this error? Can u plzz help me with this ?
If you want to import geometry from other modeling software, you need to do CAD Configuration. kzread.info/dash/bejne/i5OFucmniJjJk6g.html
@@MechTechSimulations i m facing issue while doing meshing. Can u help me out with this ?
Please contact me at [email protected]
Thank you for the explanation!
You're welcome!
can it be done in ansys 2020
Of course yes..
It needs multiphase simulation..
how if I want to simulate the undershot turbine? what do I need to do in order to simulate the blade which in contact with water?
Nothing else, just change the fluid to 'liquid water' under the cell zone conditions.
I’m using solidworks to draw the turbine and then import into ansys. Then I follow ur step to do but can’t. I create the enclosure but it show an error (operation would result in non-manifold bodies).
If I create the cylinder and box through 1) click icon “create” 2) choose icon “primitives” Is this same as enclosure u do in this video?
And also my turbine is not fully immersed in water, can I make an enclosure cover half of the turbine?
But a combination of 3D, Transient and Multiphase is really challenging and needs a heavy computational power.
There is a shortcut, in 4:10 you can factor the (-1+λ) into the expression (1-λ)(1-3λ+λ^2) -1+λ = 0 (1-λ)(1-3λ+λ^2) - (1-λ) = 0 (1-λ)(1-3λ+λ^2-1) = 0 (1-λ)(λ^2-3λ) = 0 That way, the three eigenvalues can be found momentarily and there is no need to solve a cubic equation and perform long division.
thank you
You're welcome
Can tell me the "methods" used
I hope all the methods and details are included in the video. Can you please elaborate on what you mean?
网格化一直报错
如果您需要帮助,请通过 [email protected] 与我联系。
Fail ho gya drawing mein
Brillince work sir within short😊😊time ❤❤❤
Thank you..
Sir w there is 2nd diagram also there in which one edge is parallel to base that diagram also correct sir for this question
Sorry, I didn't understand your point. Can you please specify the time in the video where you have this question?
@@MechTechSimulations diagram sir hexagon
what is the formula to calculate the mass flow rate in channel flow over cylinder in 2 dimension? Please reply
do I need to consider the cross sectional area in case of a 2D contour?
If that is a cylinder, we need to select axisymmetric instead of planar in Fluent's general settings. In 2D simulations, the mass flow rate is computed and reported in Fluent by considering the third axis as 1m by default. You can change this in the reference values if you have the third axis dimension.
Thank you I am finding this question answer Tomorrow is my exam it help me alot❤❤❤❤
Most welcome 😊
Brilliance smart work 😮😮
Thank u for your appreciation!
Hey sir how can we generate a video for the above solutions without saving the photos
Try setting up phase contours in Graphics and Animations, then create and define a Solution Animation under Calculation Activities. Preview and save the animation as a video by clicking Write/Record.
Hello sir, I'm making all the things same but my program gives me floating point error, what can I do about it? I tried to smaller and bigger mash sizes but it didnt solve.
Try without the acceleration, so we can determine whether the problem is with the acceleration or something else..
@@MechTechSimulations I runned again without acceleration and it didnt give error, tried again with linear acceleration and it gave an float error message again
@@MechTechSimulations I tried without acceleration and it didnt give float error message. When I add acceleration it gives error whatever its linear or time related. And for extra information ım trying to work on 3D tanks.
Crisp and to the point.
Thank you for the appreciation...
I think we can directly use spectral theorem for symmetric matrix/self adjoint operators
OK sir
Thank you sir
Welcome
Hello would you tell me how much the température is about in the exit of the collector?
Here are the steps to obtain the pressure at the outlet: Go to Reports, then Surface Integrals, select Average, followed by Average of Pressure. Choose the outlet boundary and click on Print. This will provide you with the average pressure at the outlet.
@@MechTechSimulations thank you for the help i will try later
Nicely explained. Thank you
You are welcome
Beautiful explannation sir tysm strainght to the point
You're most welcome
Hats off to the teacher !!! Great and conceptual teaching.
Thanks a lot
Hi, How can I run a long transient simulation with solar ray tracing? Regards
You need to activate the DO radiation model and proceed with proper transient settings, such as timestep size and number of timesteps
Do you mean that a solar load calculation only activating solar calculator does not allow to do simulations for more than 24h?
What you are drawing is not visible instruction not clear i got red fort
Sorry... Will ensure proper visibility in upcoming videos...
Hi, Im doing a final project research and I would like to obtain the thermal conductivity of the material of the heat generation. Appreciate it 🙏
Unfortunately, as far as I know, ANSYS cannot calculate thermal conductivity on its own. Instead, we must input the thermal conductivity value obtained from experimental data or reliable sources like material databases. However, once we provide the thermal conductivity along with the heat generation rate, ANSYS can generate temperature distribution results across the entire domain.
Please do an updated one for Ansys 2024 Student version if possible, thank you so much for this video.
Thank you so much for your kind words. I was actually considering creating videos with the latest versions already, so your reminder is greatly appreciated. I'll get to it soon.
nice video,thanks for sharing BTW if anyone need encapsulate solution please kindly let me know😊😊
Thanks for this example. I thought K-E cannot be used for the vortex shedding analysis and only LES or DES should be used. I need to run a case for vibration analyis and need to know the flucutatyion of the pressure the frequency. Could you explain if K-E can be used. As far as I remember only LES results can be used for the FFT etc.
Actually, it's my attempt to compute the frequency of flow-induced vibration. However, as you mentioned, there will definitely be differences between turbulence models. I've explored this in the video linked below. kzread.info/dash/bejne/lIt_17ChaKqYeaw.html
how can i delete a face, i want the top be open.....when i used the create and delete option it distorted the model
Sorry for the delayed reply. You can simply set up a pressure outlet boundary condition on that surface if you only need an opening and want to monitor variables within the domain. However, if you're also interested in understanding what happens beyond the outlet, you'll need to extend the fluid domain outside as well.
If that does not work because your model is not watertight you can do it on Ansys Discovery tool
Yep, I'm on a exploration mission! Although, I might be late to the party of discovery...
U SAVED ME!!! God bless you
Thank you so much. May God bless you too...
Beautiful presentation. Straight to the point. No nonsense.
Thank you for your appreciation
Thank you sir for your wonderful explanation ❤
You are most welcome
Thank you mam
Most welcome 😊
Excellent Explanation
Glad you liked it
thank you
You're welcome
Thank you for making this lecture very interesting and interactive. I would appreciate it if you would share the PPT also.
Kindly share link for geometry please because description link won't open.
Sorry, I hadn't noticed that the link is broken. Please email me at [email protected] or visit mechtechsimulations.com now
Sir how to modify trailing edge and find cl cd value of different angle of attack.
We can do that in two ways. One is at the geometry level by providing a certain angle with horizontal or vertical reference. The next one is body transformation
Why doesnt this equal the drag force equation?
Dear Becker.. The equation for the force exerted by a jet on a plate is derived from the momentum equation, is specific to the interaction between the jet and the plate, considering factors such as the angle of incidence and the change in momentum of the fluid. On the other hand, the drag force equation is more general and applicable to various shapes moving through a fluid, incorporating a "drag coefficient" to account for the shape and characteristics of the object. Therefore, while both equations involve forces in fluid mechanics, they address different scenarios and considerations.
very helpful!!! i was searching how to rotate than i find you
Glad it helped!
Thank you
You're welcome
Thanks a lot for the video, it was really helpful. However when I want to mesh it it says that it can`t be done for some problems. I have delated the solid part and it still says that there are problems with the mesh. Any idea about how I can do it ?
Really sorry for the late reply. Have you managed to tackle it? If not, could you share some screenshots of the error? I'll take a look and see what's up...
sir at 2:13 min how can you bring the coordinate system like X, Y, Z component at left of workspace ?
Actually, at that time, I hadn't done anything yet. I simply created the initial geometry with the origin, so it's just sitting there...