Piss poor engineering, but a great video of how to disassemble. Who would design something like this 😮
@cherandissanayake953020 күн бұрын
When that noise comes that means you broke it the super clutch you broke it and you know that that's loose again the middle of this
@joewho816820 күн бұрын
I think you're missing a bearing that goes between the two out put gears to join them
@trialnterrorАй бұрын
Best how to on KZread I’ve watched so far! Great job sir! 👏
@zZBucketsZzАй бұрын
I've had mine for 2 weeks running on 2s lipo. After a 20 minute run it shut off because of heat, so I thought. The next day it wouldn't move and after some trouble shooting, it turns out one of the fingers holding the brushes on snapped off. lol
@mazdaman19822 ай бұрын
You did not show how to reconnect the motor to the diff
@WildcatArts3 ай бұрын
I burned out the old 550 MEGA 12 that my Arrma Sento came stock with by running a 22t pinion gear in it... I think I killed it. I unfortunately refuse to downgrade my pinion gear though and hope this motor conversion lets me keep running it.
@waragainstmyself115922 күн бұрын
Got the same mega.. my car steering works but all of a sudden my motor won't work. It shoes light as red when I hit accelerate but no wheel movement.
@nrd5153 ай бұрын
I have bad hands and found that getting a 7MM wrench with a larger diameter handle makes putting the wheels on/off much much easier. I found a cheap one on Amazon and bought a pair of them. One at home, one in the car toolbox. Brand is Auvotuis. I was using a wrench like you did in the video and it was difficult to remove the nut. Too many cars worked on, too many fights as a bouncer, and old age make your hands hurt!
@rccarsandmusic26413 ай бұрын
To set the slipper its 1.5 turns out thats factory
@austinfisher1223 ай бұрын
Doesn’t work, my esc and receiver are built into one, followd this video and just ended up having to spend more money
@waragainstmyself115922 күн бұрын
For the senton? You remove the stock esc
@davidthomas45853 ай бұрын
I just got a clear body for my rc truck. Didn't even occur to me to paint the inside of the body, lol. Thank you for the video. What exact brand(s) of the metallic backer and paint did you use. You might have said it but I missed it. Thanks again!
@Rcjamaica8764 ай бұрын
What color red is it please metallic???
@user-or1uu7yt9n4 ай бұрын
So it's a 2mm to take out the screw and a 2.5..to put it back in and do you need to put thread locker on the screw ??
@TommasoVario4 ай бұрын
Thank you your video helped me fix my arm.
@kevingalea925 ай бұрын
Myself I score the body all around with the hobby knife then I cut out the wheels but I see you did a good job came out really nice bud
@keithsanchez32575 ай бұрын
This was very helpful, thank you.
@justinfraziet68436 ай бұрын
So what size Lipo is in it? And did the stock ESC handle the battery upgrade ok???
@stanleydunn25986 ай бұрын
Awesome job
@fiddyfidalgo6 ай бұрын
Are the 2.5mm and 2mm driver torx or???
@drawstraw44836 ай бұрын
Is it the same arm as on the granite? And have you heard of people using a little longer arms? I just broke a front a arm , very front where the pin slides in, and I'm looking at these aluminum one's now but want just a bit more width on it to add stabilization. Already done shocks. Any time your not busy if you happen to know. I know that this is a senton. I'm really pretty new to this. Got tools though and the means to upgrade. Just want to go in the right direction, strength and stability. Thanks
@joeman2055 ай бұрын
I’d also like to know if this is the same as the granite and if there are other ones to use. I broke mine in the same spot
@drawstraw44835 ай бұрын
@@joeman205 well I found out you can use the Typhon arms which will surely widen the granite, and as for the aluminum arms... I have them, but did decide NOT to put them on. I just replaced the A-arm with original OEM arm. The reason for not using aluminum's is the next time I have a collision it will send the impact to something much more costly to replace, chassis.
@dannymckinsey2086 ай бұрын
It was a month ago I tore into this thing and got a new motor. Thanks for showing me what I forgot. It runs like new again!
@samclingan10847 ай бұрын
But what about the bearings? How to get the one off the back side?
@forestqc697 ай бұрын
Thanks! Well made!
@zbroomeful8 ай бұрын
This was so helpful thanks so much dude
@brianreardon77008 ай бұрын
My engine is brand new but I broke of the little hook for the battery wire on the engine mount.. wonder is it’s even worth it to buy a new one and take everything apart? It really dose not effect anything.. it’s just bothering me haha
@PAULRC13449 ай бұрын
I have the same exact setup with the red version. My stock esc malfunctioned and did a runaway causing the esc and motor to smoke. So this upgrade had a reason lurking behind it.
@MonkeyNuttsRacing9 ай бұрын
thank you so much, me and my dad stayed up all night taking the entire rear end apart, i would have never guessed you snap it right off
@Andriu_FPV9 ай бұрын
How to break your slipper hub lol
@ravenshield782310 ай бұрын
Nice job, really sexy.
@marshall115710 ай бұрын
just got a brushless, thanks for showing how to replace motor.
@Luzein111 ай бұрын
Hola, vi que no usaste pintura Tamiya ¿Que marca es la que usaste?
@keygannicholls2311 ай бұрын
Very helpful! Thank you!
@rccarsandmusic2641 Жыл бұрын
Get the new clutch
@jamesmartin7656 Жыл бұрын
Please tell me how you did this with the sour gear I’m stuck
@EJJ123 Жыл бұрын
First time owning a nice RC truck I had it one day and I got a little rock in the motor your video is very helpful to someone who is new to the hobby
@BanditAviation Жыл бұрын
Has this ESC and Brushless motor have given you any problems? I just bought me a 4x4 Senton Brushed on sale.
@nandeesvarangunasekran2182 Жыл бұрын
What the code of this pain?? Is that lawa orange? Or candy red?
@jamesmartin7656 Жыл бұрын
Also what spur gear do you need to run that 130 motor combo for the senton mega
@jamesmartin7656 Жыл бұрын
What size pinion gear do you need for that 130 amp motor?
@SACSRmainestrong Жыл бұрын
Perfect this is exactly what I was doing
@darkstar189 Жыл бұрын
Thanks a lot. Never would have known how to get the motor out without this. Had trouble getting that little gear off the old motor. It was really stuck on there. Happened to have a hammer nearby. Used the claw end and pryed it right off!
@footballred8 Жыл бұрын
Have you had any issues with this motor? I just installed mine, and something has came apart internally, after only 1 battery
@Chirpy_Ceilingbird Жыл бұрын
The loud SNAP let’s you know it’s working.
@rickyking-gonzalez393 Жыл бұрын
? What was the paint on the body at beginning video "chameleon"
@kenadams4847 Жыл бұрын
Good video took time to explain the stuff and not rushing through it, keep the videos coming.
@dylansowder6617 Жыл бұрын
I tried to follow this video but my spur spins very free with the screw all the way tight I don’t want to put it all back together just for it not to work still my clutch disks all look fine the car is still pretty new
@raidersperez1278 Жыл бұрын
Can the traxxas 4tech 2.0 motor, receiver and esc swap into this ? I accidentally snapped that chasis in half and I’m looking into this one. I had just purchased a brushless motor for the traxxas mustang and I don’t wanna buy another one.
@JoseRomero-qw4zm Жыл бұрын
When I installed my motor it went faster going backwards then forwards
@nathans.8063 Жыл бұрын
Did you figure out what was wrong?
@674tonythompson Жыл бұрын
Nice work 👏
@johnfr07 Жыл бұрын
This helped me allot to fix my boy's RC. Thank you so much for the great and accurate explanation
Пікірлер
Piss poor engineering, but a great video of how to disassemble. Who would design something like this 😮
When that noise comes that means you broke it the super clutch you broke it and you know that that's loose again the middle of this
I think you're missing a bearing that goes between the two out put gears to join them
Best how to on KZread I’ve watched so far! Great job sir! 👏
I've had mine for 2 weeks running on 2s lipo. After a 20 minute run it shut off because of heat, so I thought. The next day it wouldn't move and after some trouble shooting, it turns out one of the fingers holding the brushes on snapped off. lol
You did not show how to reconnect the motor to the diff
I burned out the old 550 MEGA 12 that my Arrma Sento came stock with by running a 22t pinion gear in it... I think I killed it. I unfortunately refuse to downgrade my pinion gear though and hope this motor conversion lets me keep running it.
Got the same mega.. my car steering works but all of a sudden my motor won't work. It shoes light as red when I hit accelerate but no wheel movement.
I have bad hands and found that getting a 7MM wrench with a larger diameter handle makes putting the wheels on/off much much easier. I found a cheap one on Amazon and bought a pair of them. One at home, one in the car toolbox. Brand is Auvotuis. I was using a wrench like you did in the video and it was difficult to remove the nut. Too many cars worked on, too many fights as a bouncer, and old age make your hands hurt!
To set the slipper its 1.5 turns out thats factory
Doesn’t work, my esc and receiver are built into one, followd this video and just ended up having to spend more money
For the senton? You remove the stock esc
I just got a clear body for my rc truck. Didn't even occur to me to paint the inside of the body, lol. Thank you for the video. What exact brand(s) of the metallic backer and paint did you use. You might have said it but I missed it. Thanks again!
What color red is it please metallic???
So it's a 2mm to take out the screw and a 2.5..to put it back in and do you need to put thread locker on the screw ??
Thank you your video helped me fix my arm.
Myself I score the body all around with the hobby knife then I cut out the wheels but I see you did a good job came out really nice bud
This was very helpful, thank you.
So what size Lipo is in it? And did the stock ESC handle the battery upgrade ok???
Awesome job
Are the 2.5mm and 2mm driver torx or???
Is it the same arm as on the granite? And have you heard of people using a little longer arms? I just broke a front a arm , very front where the pin slides in, and I'm looking at these aluminum one's now but want just a bit more width on it to add stabilization. Already done shocks. Any time your not busy if you happen to know. I know that this is a senton. I'm really pretty new to this. Got tools though and the means to upgrade. Just want to go in the right direction, strength and stability. Thanks
I’d also like to know if this is the same as the granite and if there are other ones to use. I broke mine in the same spot
@@joeman205 well I found out you can use the Typhon arms which will surely widen the granite, and as for the aluminum arms... I have them, but did decide NOT to put them on. I just replaced the A-arm with original OEM arm. The reason for not using aluminum's is the next time I have a collision it will send the impact to something much more costly to replace, chassis.
It was a month ago I tore into this thing and got a new motor. Thanks for showing me what I forgot. It runs like new again!
But what about the bearings? How to get the one off the back side?
Thanks! Well made!
This was so helpful thanks so much dude
My engine is brand new but I broke of the little hook for the battery wire on the engine mount.. wonder is it’s even worth it to buy a new one and take everything apart? It really dose not effect anything.. it’s just bothering me haha
I have the same exact setup with the red version. My stock esc malfunctioned and did a runaway causing the esc and motor to smoke. So this upgrade had a reason lurking behind it.
thank you so much, me and my dad stayed up all night taking the entire rear end apart, i would have never guessed you snap it right off
How to break your slipper hub lol
Nice job, really sexy.
just got a brushless, thanks for showing how to replace motor.
Hola, vi que no usaste pintura Tamiya ¿Que marca es la que usaste?
Very helpful! Thank you!
Get the new clutch
Please tell me how you did this with the sour gear I’m stuck
First time owning a nice RC truck I had it one day and I got a little rock in the motor your video is very helpful to someone who is new to the hobby
Has this ESC and Brushless motor have given you any problems? I just bought me a 4x4 Senton Brushed on sale.
What the code of this pain?? Is that lawa orange? Or candy red?
Also what spur gear do you need to run that 130 motor combo for the senton mega
What size pinion gear do you need for that 130 amp motor?
Perfect this is exactly what I was doing
Thanks a lot. Never would have known how to get the motor out without this. Had trouble getting that little gear off the old motor. It was really stuck on there. Happened to have a hammer nearby. Used the claw end and pryed it right off!
Have you had any issues with this motor? I just installed mine, and something has came apart internally, after only 1 battery
The loud SNAP let’s you know it’s working.
? What was the paint on the body at beginning video "chameleon"
Good video took time to explain the stuff and not rushing through it, keep the videos coming.
I tried to follow this video but my spur spins very free with the screw all the way tight I don’t want to put it all back together just for it not to work still my clutch disks all look fine the car is still pretty new
Can the traxxas 4tech 2.0 motor, receiver and esc swap into this ? I accidentally snapped that chasis in half and I’m looking into this one. I had just purchased a brushless motor for the traxxas mustang and I don’t wanna buy another one.
When I installed my motor it went faster going backwards then forwards
Did you figure out what was wrong?
Nice work 👏
This helped me allot to fix my boy's RC. Thank you so much for the great and accurate explanation