Пікірлер

• 
  @sdyksterhouse6 күн бұрын

  Do both remote and car need to stay on when doing this?

• 
  @sdyksterhouse6 күн бұрын

  How do u know which way too turn backwards or forwards

• 
  @djsprc5 күн бұрын

  On which way you need to turn it depends how your alignment is off. You can do it with the vehicle on and remote, but be careful not to put too much pressure to break any gears in your servo. I would make sure that your trim on your remote is centred turn everything on the servo will centre itself then I would turn everything off and do the alignment

• 
  @DakAiralednac6 күн бұрын

  Sonwhat is thjs? Can i usr rubber cement like for a tire patch?

• 
  @djsprc6 күн бұрын

  That kind of glue might work. If you have access to crazy glue, that would work too.

• 
  @chuckdeezy838013 күн бұрын

  My CR touch, touches the fan. Guess I can double check if it's fully low and retighten. Unlucky because it's mid print and noisy lol.

• 
  @djsprc13 күн бұрын

  @@chuckdeezy8380 that’s unfortunate. Yes, there is some play in it. You might’ve put it a little bit too close to the side fan once your print is done. Loosen your screws and try to move it out of the way. The other thing to make sure that you don’t have your wires on that side. If you do flip it opposite, it might be your wireless touching too.

• 
  @Silverwood4415 күн бұрын

  What did you use for your x and y hotend offsets?

• 
  @djsprc14 күн бұрын

  Every printer are not the same, even if I gave you my settings and may not work for yours.

• 
  @SzabolcsCzeh25 күн бұрын

  My experience : depending only on the shock piston size, and the holes on it. Thicker oil needs bigger holes for a better flow. The best oil is, which is never bubbling up, while fast pistons movements. Lower speed cars need bigger holes on piston and thicker oil, high speed cars need more liquidity oil with smaller holes on pistons. So only information I need when I buy shocks, are the piston parameters. I bought cheap shoks from AliExpress, and tripled its value by 3D printing modified pistons...

• 
  @TheCunningStunt26 күн бұрын

  bro. you didn't even boot it up and show it works. Any issues with the Touch Probe? My ender 3 Max I just installed a Sprite and won't work with my CR Touch, I have to connect the probe directly to the mother board with the original cable for it to work. Seems like this is a common problem. But yeah, always a good idea when you show setting up new hardware to show the finished product actually running. This way you can address any potential problems you encounter.

• 
  @HandydeeznutsАй бұрын

  No

• 
  @Its.KevinsАй бұрын

  Why is mine flashing red and green???

• 
  @ranchchipsАй бұрын

  very helpful , thank you!

• 
  @digitalsmithyАй бұрын

  can you easily fit other branded bodies on this?

• 
  @djsprcАй бұрын

  As long as the same wheelbase should not have any issues. Only body post modification you will need to do.

• 
  @digitalsmithyАй бұрын

  @@djsprc right on!

• 
  @bar1bar1Ай бұрын

  Cable doesn't fit....

• 
  @right-behind-youАй бұрын

  A little more difficult on my 1/8 🤣

• 
  @6Fallen_Angel666Ай бұрын

  Hey i wand to change the oil in my 140mm shock's but i use then for my fanatec csl dd padel's any suggestions on what type of oil i shut use if im using them for my gas and brack padel

• 
  @greenie432 ай бұрын

  Informative vid!! 😎👍

• 
  @chrisspearline7672 ай бұрын

  Why does the transmitter need to be on for this?

• 
  @djsprc2 ай бұрын

  That way you know your servo is on the zero position

• 
  @david-_-27492 ай бұрын

  Thank you, helped so much with my rustler!!!

• 
  @Hungrybird4742 ай бұрын

  Thank you . I m still afraid to mess it up but if I count the turns I can always go back but I ll get it right . Mines brand new and reminds me of girls with big boobs where the nips are pointing to the side 😂

• 
  @kenyanr12 ай бұрын

  How’s this servo holding up?

• 
  @djsprc2 ай бұрын

  It’s holding up great.

• 
  @kenyanr12 ай бұрын

  @@djsprc Cool, thanks for the reply. Did you have any issues with the linkages?

• 
  @djsprc2 ай бұрын

  I do not remember 100%. I did have one issue but it’s mentioned in the video besides that no

• 
  @Jay-ws7tv2 ай бұрын

  Thank you!

• 
  @johnlujan87062 ай бұрын

  It's fun to drive!

• 
  @xanielton.7142 ай бұрын

  If iv been using 2s lipo the whole time on this one would I need to do anything before I try a 3s? Or can I just plug and play? Iv never had a 3s battery never got around to it even tho it’s capable.

• 
  @johnlujan87062 ай бұрын

  Good video! 👍

• 
  @pedropablomorarojas70213 ай бұрын

  What oil should I use for a hpi e-savage 8 shocks 140mm 1/10

• 
  @djsprc3 ай бұрын

  I would use 50 or 60.

• 
  @MdRakibul-yl4so3 ай бұрын

  😊😊😊

• 
  @MdRakibul-yl4so3 ай бұрын

  আমি এই গারি নিতে চাই

• 
  @snakes3012713 ай бұрын

  why are you using a needle tip on 10awg wire!!? use the right tip and you would be done in 5 seconds

• 
  @kirkearl3 ай бұрын

  Thanks!!!!

• 
  @VijayGangaram3 ай бұрын

  Djsprc, nice run of your sonic wake V1, I am Linden Stewart from Georgetown Guyana in south America, I have the sonic-wake V1. 😊the problem with my Sonic-wake V1 when ever the boat flips over, it takes a long time to self right, about 3 minutes or more. By that time the water gets into the battery compartment and the boat won't start, I have to go to retrieve it. Is their anything you can recommend so I can correct that problem?

• 
  @djsprc3 ай бұрын

  Just make sure that your battery is positioned at the correct place half the time is a battery not position correctly will prevent from flipping back. Make sure you use some tape around your hall hatch to prevent water from going in.

• 
  @LectricLetus3 ай бұрын

  Thanks for the insight. Seems obvious now.

• 
  @fabiankempe53323 ай бұрын

  can you help me? I can't get the software installed, I did everything exactly as you said but the printer won't download it from the card...

• 
  @djsprc3 ай бұрын

  You will need to confirm the model of your board and these printers they made two models for the main motherboard. The software that I use is made for a specific board. V4.2.3. If you don’t have that model, unfortunately it will not work. Now, if that’s the model you have I would suggest to try a different SD card. Do not use a high capacity card.

• 
  @fabiankempe53323 ай бұрын

  Thanks for the fast answer. Does the CR have to be connected beforehand?@@djsprc

• 
  @djsprc3 ай бұрын

  @@fabiankempe5332 you don’t need to

• 
  @kevinh8453 ай бұрын

  What if my battery only has three leads on the balance connector and not four I can't seem to get the purple light blinking only a steady white light

• 
  @susiejinright24703 ай бұрын

  What is it worth?

• 
  @djsprc3 ай бұрын

  They are not sold in stores. It’s only through the Snap On trucks.

• 
  @susiejinright24703 ай бұрын

  How much is it.

• 
  @davidryan70723 ай бұрын

  Thank you. It helped me.

• 
  @djsprc3 ай бұрын

  Glad to hear that!

• 
  @jhonnypenacho4 ай бұрын

  Number 707 it's mine XD

• 
  @BigCheese854 ай бұрын

  Hot racing jig? You should tape up each loose wire as you dont want them accidentally touching. Ic5 are more expensive but easier to solder than Ec5

• 
  @steelphil55394 ай бұрын

  Why does my car zig-zag, what do I need to adjust 110 scale Fox Edition made by Traxxas

• 
  @geoffpeacock5144 ай бұрын

  You mentioned on your video getting custom firmware from Reddit Would you happen to have a link please Also i read your other comments and you said about running klipper Did you do a video on the changeover to Klipper and is it working ok?

• 
  @djsprc4 ай бұрын

  On reddit just do a search for firmware. And yes my printer is running Klipper (mainsail) and love it. I did not do a video on. How to do the set up if you go on mainsail website, they explain it very well. And one of the things I like about mainsail is if you need to do a modification in the firmware, you don’t need to compile the firmware completely again.

• 
  @drewp91124 ай бұрын

  nice to see someone posting this, i have also been at it for a fairly long time, couple points ill add....you can buy alignment tools for rc cars most do it by eye, its fair to say most probably dont even know if their cars have adjustable turnbuckles or where there located so your info will likely be new info to some. . you should try to adjust them the same amount for both sides, sometimes they come uneven from the factory this can lead to the servo trim needing to be centered. calipers work for checking the distance between ball ends. adjust based on cars full weight on the tires. raising and lowering affects toe and camber depending on the car some vary a lot more than high end racers will. some will argue about using toe in, and you see them always complaining about high speed erratic handling car swerving etc though absolutely refuse to blame toe out and rather replace servos tires shocks etc etc before never considering toe regardless of how many wrecks. example:high speed run, toe out. acceleration toe out is reduced in 4wd csrs due to the wheels pulling against any slop in the steering becoming neutral or even slightly toe in depending on car and wear. once the car stop pulling hard nearing top speed this becomes more toe out again and unfortunately any ground imperfections can send it into the weeds very quickly. braking will also cause even more toe out as the front end dips lower then the front end is just fighting for which tire will get or loose traction first.i prefer a little toe in on my dirt track cars, vs more neutral toe on the pavement. generally i dont ever prefer toe out, though this might be good for small racetracks with a lot of curves and short straights. in the end there are many things that affect handling probably more so in a rc than a 1to1

• 
  @thetruth78394 ай бұрын

  Thank you

• 
  @ErrythingPhroze4 ай бұрын

  Straight to the point. Thanks man

• 
  @anthonytheriaultthibodeau4 ай бұрын

  I recently bought a new Traxxas Bandit Rear Wheel Drive 1:10 Scale and I believe it doesn't have any oil in it right now. I like in your video the part where you explain to do drag racing that it's better light in the back and heavy in the front. You use 42.5 in the front and 37 in the rear for one of your cars, should I do the same for my Traxxas Bandit or you have better recipe. I won't do jumps too steep but can a foot high sometimes.

• 
  @drayvaind61034 ай бұрын

  perfect no bs exactly what i needed

• 
  @clarencegilmore62804 ай бұрын

  I keep getting ch 1 errors on my😢

• 
  @djsprc4 ай бұрын

  Your charger might be defective, depending on when you bought it it might still be under warranty. I would verify with Horizon hobby.

• 
  @aliasangelalias4 ай бұрын

  i always get confused by what turning direction does what? I could be turning but not sure if it is in or out.. what's a simple way to remember?

• 
  @PhilKeys4 ай бұрын

  What cell do u for a Nimh Traxxas 3000 man battery

• 
  @djsprc4 ай бұрын

  It depends on amount of cells you have is it a six cell or a seven cell. Count the amount of batteries that you have to get her.

• 
  @user-or1uu7yt9n4 ай бұрын

  I started using the FT silicone shock fluid 42.5 w . Not to heavy and not to light for my Big Rock . It just seems to give me better control and smoother ride . And if I do need more cushion it is easier to switch tires than it is shock oil .

• 
  @djsprc4 ай бұрын

  Thanks for sharing

• 
  @ludwigcruz15905 ай бұрын

  Que numero de pieza son los baleros o cojinetes que cambiaste (Traxxas)?

• 
  @user-wp9mz5 ай бұрын

  Mine flashes red but it doesn't make any sound does that mean it's okay or what am I doing wrong I just bought this and I have no clue

• 
  @djsprc5 ай бұрын

  Is it moving if it’s moving? Yes it is.

• 
  @user-wp9mz5 ай бұрын

  @@djsprc I messed around with it a little bit more yesterday I finally got it figured out the red light is staying solid lit now the truck is moving everything is working I believe it was set up for lipo from the factory not nickel metal hydride but I think it's okay now I am very impressed by this truck especially the quality but keep in mind this is my first Traxxas

• 
  @djsprc5 ай бұрын

  @@user-wp9mz if I remember correctly yes it should stay solid when you’re going forward or reverse now if you have a greenlight, that’s a Lipo mode.

• 
  @user-wp9mz5 ай бұрын

  @@djsprc okay that's what I was figuring thank you so much the light is definitely staying red so it should be good for nickel metal hydrate now

• 
  @tobiasbuitelaar4815 ай бұрын

  How come this is the only video i can find, that says NOT to fill your diffs with oil of grease? Every other video explains the effect on the behaviour of your car bij filling the diffs with different types of oil, etc. Its kind of like the opposite of what you are telling in this video. Correct me if i am wrong.

• 
  @djsprc5 ай бұрын

  When I’m telling you is not to fill the cavity that your diff lives in, if you do, your oil will just leak out. You can add a little bit to your gears to prevent them from chattering.

• 
  @tobiasbuitelaar4814 ай бұрын

  @@djsprc i see, thnx