Hi, My Channel is about sharing a lot of how-to Video's. because I know how hard, it is to live in a concrete jungle. I am not a mechanic, but out of frustration I learned auto care. I can make my own clothes, fix electronics, create and design what every comes to mind, I am Thankful to be able to share, take a look at the video's they speak for themselves.
Пікірлер
cannot hrar yuo😊
All I heard was my little nipples..
Was this giving a c0237 check code
yes.
I had no idea what you said....First was due to the beeping....Shut the car door! Second was because someone nearby was using a lawnmower. If you want us to hear you, please be aware of your surroundings. The microphone picks up ALL of those sounds.
God put those words in your head what to say it to reach someone. perfect timing
Buy a Ferris Zero turn....you will be much happier. And so much fun to ride.
Its the intake valve on them they are carbon up! You will need to clean the intake valves by sandblast or take off the intake and cleaning each port where the intake valve closes so you can clean the top on the intake that never gets cleaned
good stuff!
What part number
Part# NM4070
Auto Zone
Cant nobody see that 😡
sorry about that. tite space low light.🙏
Standing in front of example
sorry about that, Elizabeth
Also if you cut a piece of pvc on a 45 on the waste end that water will follow the point instead of dancing around a straight cut.
good stuff!
New a co2 blast device. Conical rubber on one end, stick it in and blast. Usually works on cold water gunk clogs.
thanks
Hack is right.... Do it right and fix it ONCE! Remove the water, add your fill rock, mix fiber reinforced crack resistant concrete, fill, vibrate to assure fulfill without air pockets and smooth, imbed top with gravel, let it set, then wash and brush to reveal the gravel top. It's not harder than what's shown , and will last indefinitely.
If you had to replace the resistor, I would recommend also replacing the blower motor. Generally they go out because of excessive heat caused by the blower motor taking more amps to run as the blower motor brushes wear out.
good stuff!
loosen the motor mount. move engine out the way. take move frame to the side. and belt is off .
I have a 98 ford explorer v8 5.0L the eddie bauer edition and my vents smell awful when i use the air. I have been trying to find the drain line or hose with no luck. You have any idea where it might be? I have been wanting to change the cabin air filter out in it also but i'm not sure if it has one. Thanks
with the air conditioner on, check along the fire wall. near the a/c dryer receiver. looking for water dripping. that vehicle doesn't have a cabin filter. I replaced my evaporator core and it made a big difference also.
Cracked cylinder head? No that's leaking spark plug well seals. Needs cam cover gaskets. If you're telling people that's a cracked head you're trying to rip people off
thanks, this Kia had both.
Thanks for not showing how to disconnect. Came here to see one thing and it wasn't shown.
you are rapping the tool around the line and pressing it into the line, it opens up the round spring. the. you can separate the lines.
you are rapping the tool around the line and pressing it into the line, it opens up the round spring. the. you can separate the lines.
That is nothing bro, at least u do not have to take out the wheel to do the light change😂
Great videos
Ok thanks for the response. Where can I buy the metal sleeve that the unit goes in?
eBay
Ok I will try! Thanks
Ok thanks for the response. Where can I buy the metal sleeve that the unit goes in?
Is that 110 or 220 volts
110
Also on the caddy 06
My Mazda 6 is the same bumper comes off
grab some zip ties, Christmas tree inserts, sews. and get under there and tie it up.
For anyone that watches this video, the 2 top bolts are only to be loosened and the rest of em removed. Then u lift up the regulator and the bolts fit thru the openings. The bolts act like hooks to help with removal and installation.
Keep it up your doing great
thanks
It would help if you describe what you’re trying to fix! I assume reconnecting a radiator?
Your so cheap , i bet you buy used brake pads.
directions say to NOT use a impact only a ratchet. your welcome.
the impact works great, when you are working alone, trying to move the transmission around. you're welcome.
@@diversity2739 im glad it works for you. i didnt want to try it thinking it might break and my trans is still on it right now. hf trans jack ftw!
Not sure I've ever yawned so intensely before in my life!
Wheel bearings fu ked
ahh,so so.
I'll call you back, nit home. Helping someone .
good job
thanks
I feel that on ford expiditions you cant just change the headlight bulb neither you its either the balast or the whole headlamp assembly
unbelievable!
Yeah that's supposed to be the washer first then the rubber garment. Then you put it up then you put the rubber garment on and then the washer. That was wrong the way you were putting it in. I'm just saying that so you know
Muchas gracias ☺️ me a salvado 😅
bienvenido
Very good guide on pulling apart the machine. The only issue I had was putting the tension wheel back in place when putting the machine together. I realise now the metal stick goes on the left of the lever, not the right.
thanks, Emily we can all teach each other.
You will NOT be able to get good pedal on that system. You will need a proper scanner, not a code reader, to do automated bleed for the valves in the new unit. I always just change the computer side, thw valving very rarely goes bad.
good stuff!
Great
Fun stuff
Did you knock it out?
Just use the buet off of an old plug wire
what kind of glue did you use?
it wasn't glue, you can use any window sealer. or thick clunking.
Spark plug sockets are made and sold every day...but rigging is fine too
They make socket with magnet
Love your videos
thanks, for watching
The 6:18 mark of the video is by far the most informative.
Oops! don't know what happened.
Thank you so much for making this video, you have saved me a lot of time and money.
welcome
That’s the worrt sign you could see