Need mount kit in swingarm ktm quad. can give me sequence of pieces? tanks
@jerrodq973310 ай бұрын
heads up on the 2017 I have, the PDS bushing in the swingarm does have a small lip. So be careful when pressing it out that you use a socket that is small enough so that it doesn't catch on the smaller lip. I didn't see it at first but when i couldn't get it to press out I found this was the cause. It's not easily seen if dirty, and also it's quite recessed so it's hard to see. I know there is a lip on the right side, not sure on the left side.
@alftorrisi8795 Жыл бұрын
Fantastic thank you very much
@pmfilmsUK Жыл бұрын
Fantastic
@puch72612 жыл бұрын
jus subd.👌
@davidmeale95722 жыл бұрын
Don't take up teaching !
@Runk3lsmcdougal2 жыл бұрын
Awesome thanks
@52yamahar12 жыл бұрын
Couldn’t of made it any clearer, first time I’ve tried this and it’s worked a treat 👍🏻
@samsami19262 жыл бұрын
hi how did you get the software for pc? do you have the link where i can download it thx
@obonnetfe11573 жыл бұрын
Very helpful video .. I just did it today on my 540 SXS ! Thank you
@abquix4 жыл бұрын
Thanks man, really helpful
@jesseklassen20175 жыл бұрын
That’s what I was thinking of doing. I got a long bolt instead of threaded rod. Good video dude!!👍👍
@BickMitchum5 жыл бұрын
Were you the bloke who stuffed it on the straight on to the grass?
@PTG8475 жыл бұрын
Is it normal on the right side with (side with no washers) for the final barrel to have some side to side movement?
@patrickmatthews12726 жыл бұрын
Good job Maddog 👏👏🏍
@Tjhaines236 жыл бұрын
Which date and group?
@m.m144336 жыл бұрын
Brilliant
@kicekap6 жыл бұрын
Great tutorial, can You explain me directions of pushing in and out the bearings? Thanks Mate
@chriswakeham57086 жыл бұрын
Nice and consistent! 👍 Where did you place?
@Sotirg6 жыл бұрын
the other side does not have rings, no?. I bought the repair kit and only two come instead of four.. sorry for my english
@wolkenhaube6 жыл бұрын
Soti Rg there are more uses for that... not only motorcycles... as i know some electro engines need to change the rings after 20 years of running.
@michail19636 жыл бұрын
Yup. I was also puzzled at first...yes only the sprocket side used both retaining rings.
@vinuezaer6 жыл бұрын
Best one I've seen. Great explanations.
@Revy87 жыл бұрын
thanks for showing how everything sits inside. that was what I was most curious about before starting the job, i wanted to have a clear understanding of what needed to come out in what order. it was very helpful, thanks again. good tip on pointing out the ring too
@pandiannano98467 жыл бұрын
if download indian marine chart or map? please reply me... my mail id: [email protected]
@sidecarbod14417 жыл бұрын
Its worth warming up the swingarm with a blow torch so that it expands, the bearings will move with less force. It is also worth warming up the swingarm when fitting the new bearings because there less change of galling up the aluminium.
@ow-my-achilles11064 жыл бұрын
I've heard guys freeze the bearings for a few hours, so they microscopically shrink making them easier to fit. Safer than heating the swing arm and getting an ouchie..
@johnhewer07 жыл бұрын
It was a while ago but think I started the bearing off by carefully taping them in with a rubber hammer. Then used the same socket method to press them fully in. Just be careful with the dust seals as they are extremely soft.
@wolkenhaube6 жыл бұрын
maddog do not use hammer hits on the chassis
@wolkenhaube6 жыл бұрын
maddog you ride 150 mph micro cuts will make you unsave
@jflo25957 жыл бұрын
Thank you great video do you know how to put them back in for the new ones
@luisdiaz89427 жыл бұрын
very good idea and simple or easy extractor ...
@bradhall32148 жыл бұрын
Thanks for posting this video, I just tried this on my KX and it worked great!
@Asken123458 жыл бұрын
Just a thought... if you put the big socket on he right (at 5:44) and the smaller on the left you can fit both the socket pushing and the bigger at once so you don't have to pull it apart to get the second one out.
@andykerr95459 жыл бұрын
Thanks for Info mate-no need to buy a special tool thati will hardly ever need ......your ideas use stuff most mechanically minded people may already have in their workshops
@jordanheat83319 жыл бұрын
How come theres no sound?
@bmickle9 жыл бұрын
Thanks, need to do my bearings on short notice and "morgan's tool" is both ridiculously expensive and won't make it here in time. This is perfect!
@yonmoore9 жыл бұрын
Thanks for posting!
@FrankTompson9 жыл бұрын
Thanks maddog, very useful. To get around the 4Gb limit to copy over the entire UK, could you not just extract your external micro SD card from your smartphone, plug it into your pc, then copy the over direct, rather than going via your smartphone? Thanks, Frank
Пікірлер
Need mount kit in swingarm ktm quad. can give me sequence of pieces? tanks
heads up on the 2017 I have, the PDS bushing in the swingarm does have a small lip. So be careful when pressing it out that you use a socket that is small enough so that it doesn't catch on the smaller lip. I didn't see it at first but when i couldn't get it to press out I found this was the cause. It's not easily seen if dirty, and also it's quite recessed so it's hard to see. I know there is a lip on the right side, not sure on the left side.
Fantastic thank you very much
Fantastic
jus subd.👌
Don't take up teaching !
Awesome thanks
Couldn’t of made it any clearer, first time I’ve tried this and it’s worked a treat 👍🏻
hi how did you get the software for pc? do you have the link where i can download it thx
Very helpful video .. I just did it today on my 540 SXS ! Thank you
Thanks man, really helpful
That’s what I was thinking of doing. I got a long bolt instead of threaded rod. Good video dude!!👍👍
Were you the bloke who stuffed it on the straight on to the grass?
Is it normal on the right side with (side with no washers) for the final barrel to have some side to side movement?
Good job Maddog 👏👏🏍
Which date and group?
Brilliant
Great tutorial, can You explain me directions of pushing in and out the bearings? Thanks Mate
Nice and consistent! 👍 Where did you place?
the other side does not have rings, no?. I bought the repair kit and only two come instead of four.. sorry for my english
Soti Rg there are more uses for that... not only motorcycles... as i know some electro engines need to change the rings after 20 years of running.
Yup. I was also puzzled at first...yes only the sprocket side used both retaining rings.
Best one I've seen. Great explanations.
thanks for showing how everything sits inside. that was what I was most curious about before starting the job, i wanted to have a clear understanding of what needed to come out in what order. it was very helpful, thanks again. good tip on pointing out the ring too
if download indian marine chart or map? please reply me... my mail id: [email protected]
Its worth warming up the swingarm with a blow torch so that it expands, the bearings will move with less force. It is also worth warming up the swingarm when fitting the new bearings because there less change of galling up the aluminium.
I've heard guys freeze the bearings for a few hours, so they microscopically shrink making them easier to fit. Safer than heating the swing arm and getting an ouchie..
It was a while ago but think I started the bearing off by carefully taping them in with a rubber hammer. Then used the same socket method to press them fully in. Just be careful with the dust seals as they are extremely soft.
maddog do not use hammer hits on the chassis
maddog you ride 150 mph micro cuts will make you unsave
Thank you great video do you know how to put them back in for the new ones
very good idea and simple or easy extractor ...
Thanks for posting this video, I just tried this on my KX and it worked great!
Just a thought... if you put the big socket on he right (at 5:44) and the smaller on the left you can fit both the socket pushing and the bigger at once so you don't have to pull it apart to get the second one out.
Thanks for Info mate-no need to buy a special tool thati will hardly ever need ......your ideas use stuff most mechanically minded people may already have in their workshops
How come theres no sound?
Thanks, need to do my bearings on short notice and "morgan's tool" is both ridiculously expensive and won't make it here in time. This is perfect!
Thanks for posting!
Thanks maddog, very useful. To get around the 4Gb limit to copy over the entire UK, could you not just extract your external micro SD card from your smartphone, plug it into your pc, then copy the over direct, rather than going via your smartphone? Thanks, Frank
Great video, Thanks for posting this!