Пікірлер

• 
  @OriginalOrigins14 сағат бұрын

  so essentially if all the ohms and voltages are correct its a computer engine issue

• 
  @jeremyvigil976220 сағат бұрын

  Great info, Thanks

• 
  @fritglassware9165Күн бұрын

  which wires did you jump to bypass the vcim? I had 30ohms at my can bus pins not sure what would cause that. also my number 1 pin to grouns was like .5volts

• 
  @samuelnunez5380Күн бұрын

  how about a frontier that originally come with transponder vin key and you want to replace ECM with used one?

• 
  @dieselboy7138Күн бұрын

  Hey, I am trying to program a ACM for a Ford F250 2016 , complaint is no sound from any speakers, touchscreen display works fine. I replaced ACM tried to use Forscan with ASBUILT, no good. Paid for FJDS(2day one license) and using J2524. Under PMI no ACM listed, all other modules show PMI available. ALLDATA and Identifix both say PMI required for new ACM. Please help.

• 
  @lifeordeath32882 күн бұрын

  Interesting may be my issue. Had a bad window motor / regulator. I replaced the regulator with Dorman for advanced. And now my window works but the car doesn’t know when my door opens. My running boards don’t come out etc. I still have the old regulator so I may plug that in to see if the running boards work again. It’s a 2016 gmc Yukon xl Denali

• 
  @tsoe013 күн бұрын

  For some reason when I get to the vin entry on my system it limits me to 3 numbers short of my vin. I can’t seem to get around this. My truck is a 2010 F350 6.4L Cabela’s Edition. Any ideas, cause when I continue, my vehicle specification shows a vintage with last 3 numbers missing. I have tried choosing even an earlier model, no luck.

• 
  @atmphil13 күн бұрын

  This really helped I got a car same problem another shop did it and they bring it to use to fix it. This is the second time that other shop mess up this car then it come to me to fix it. Some people should not be touching cars. Why should he think cutting and removing a part of the engine harness was a good idea. You tryed your best to not call that guy stupid but he is stupid.

• 
  @nickhyslop57434 күн бұрын

  Got some bad solder? Old school computer guys would throw boards in the oven to reflow solder

• 
  @mannyautotech4 күн бұрын

  😮

• 
  @Max-j2r4 күн бұрын

  ❤❤❤❤❤

• 
  @claytoncurtis77595 күн бұрын

  So I just ran this procedure on a 2004 Navigator that I had to swap in a used PCM due to a failed COP driver in the old unit, and it went as expected until the victory run after completion... ABS vin mismatch IDS instructed me to run the PMI to correct it, so i did. Fails at the end saying the PCM has incorrect VIN, run PMI to correct it. so again, i did. gets to the end and what do you know, ABS vin mismatch run PMI to correct. Also lost climate control module completely and the a/c clutch cycles like it would if i had turned it on. have you run into anything similar? at a loss..

• 
  @bartscave5 күн бұрын

  Thanks Brian!

• 
  @glebabramov65765 күн бұрын

  Amazing information! Thank you! Very detailed!

• 
  @Mr2004MCSS5 күн бұрын

  Great diagnosis. I miss these types of videos from you. Hopefully you can do more of them in the future.

• 
  @BrianMann2165 күн бұрын

  I will see what I can do, been very busy with new employee on boarded.

• 
  @robertfrancisco11935 күн бұрын

  looks like you need to clean up or replace fuse box. must be more corrosion !!

• 
  @djosbun5 күн бұрын

  Hello Brian, How is the healing progressing on your hands?

• 
  @BrianMann2165 күн бұрын

  Not so good, been dealing with arthritis like inflammation since surgery, on some steroids now( not good) but feel good for the time being.

• 
  @DavidGutierrez-zi4dy5 күн бұрын

  GREAT!!

• 
  @sheerwillsurvival20645 күн бұрын

  I don’t miss living in Wisconsin where I cut my teeth as a GM technician in the 70s . Rust on everything. Been in Texas 40+ years no rust very little 😊

• 
  @HappyPlaceAquatics6 күн бұрын

  I can’t express checking the basics enough to my guys. Great video B Mann

• 
  @nickayivor84326 күн бұрын

  SUBSTANTIAL,Hands on Automotive Training Brian Mann Brilliant tutorials video 👍 From Nick Ayivor from London England UK 🇬🇧 ⏰️ 14:22 Good Afternoon

• 
  @BrianMann2166 күн бұрын

  Thanks for watching! I have not made a video for a while!

• 
  @BeMad4M3XD8 күн бұрын

  Dude I spent an hour and a half trying to figure out why my truck would start then stall after getting to work and finding this code, check everything else besides that fuse, instantly fixed the issue after replacing it, I'm so mad yet so happy, also had it so the driver door wouldn't unlock with the button, but I could unlock it manually.

• 
  @SkillSavvyDIY9 күн бұрын

  Best video out there on fuel trims! If someone can't understand this, then they are just not capable of understanding anything

• 
  @allan951009 күн бұрын

  Hey, so I recently changed my transmission on a 07 caliber RT, I wanted to ask for your input, my car seems to stutter as I want to pick up speed, do you think it would have something to do with the computer? And how can I go about resetting it? What’s a good toolto use?

• 
  @myfakeid600810 күн бұрын

  Hey Brian, do you read these messages still? I'm having this exact problem on my same generation CR-V. I too have a remote start that has the same exact key fob you show in The video...What is the actual fix for this? Is that Autel scan tool necessary? Thanks in advance.

• 
  @RichardSlaby-zi9bf13 күн бұрын

  Did you figure out what it was?

• 
  @felipedejesusmartinezcarre125914 күн бұрын

  Una pregunta que señales debo tener para el sensor cmp para una Silverado 2011 Tengo 2 voltajes de 5 v y una tierra es correcto?

• 
  @chasedavis235814 күн бұрын

  How to you test a can bus if There is a gateway module?

• 
  @mattsnowy465415 күн бұрын

  Hey brother! I just want to say thank you! This video is what fixed my 09 silverado. I did a motor swap on my lc9 and couldn't get it going for 4 weeks . Trouble shooting ext . From a cut harness going from my engine to my fuse block. Power distribution block. Refined all the pins . This was my last hurtle. And you nailed it! Thanks again. Your video was bang on

• 
  @chinthakafernando466516 күн бұрын

  HI there, I saw your video on youtube about TCM programming . So i got a few ford fiesta tcm and mazda 3 tcm. How can I test if they are programmed properly and if they need any programming how can i do it. I can buy the hardware and softwares needed. My biggest concern is how do I diagnose/ program the tcm without fitting the tcm to the car. I saw a lot of videos on youtube where they plug the J-box to the car to diagnose/ program. I would be happy if you could help me out. Thank you Fernando

• 
  @jaybabi188116 күн бұрын

  What u do to fix it boss

• 
  @bobbofly17 күн бұрын

  Not a popular way of framing it, perhaps, but an aircraft is indeed a vehicle. 😂😂😂😂😂😂

• 
  @user-kv2ej3ne3o18 күн бұрын

  This is for the 2005 Pontiac Grand Prix 3.8 v6

• 
  @user-kv2ej3ne3o18 күн бұрын

  My no start comes from a new computer at first installing the unit all the dash lights comes on but when time to start all lights goes off except the engine light the first couple of days when trying this then just last night the disabled message showed up now. on the old computer there’s no problem with starting at all so some how the computer is having an issue with letting me start the car

• 
  @az9385018 күн бұрын

  well done man very informative video thanks...

• 
  @wes0633418 күн бұрын

  What diagnostics/programmer are you using?

• 
  @546people18 күн бұрын

  Thanks man. This was really helpful.

• 
  @PhilOConnor-f8k19 күн бұрын

  we just had a 2015 equinox, installed chain, had constant poo17 code, checked timing 3 times, engine ran great, couldn't get light off, saw your video, ordered an exhaust cam from chevy and installed it and check engine light is off, we couldn't believe that the reluctor could slip like that. Thanks for the great job explaining it on the video

• 
  @radoslav195819 күн бұрын

  Where r you located?

• 
  @BrianMann21618 күн бұрын

  Cleveland o

• 
  @pipjr868519 күн бұрын

  What city are you located in

• 
  @jmanson6219 күн бұрын

  Mine does it as well. It’s the harness in the driver door. The repeated action of the door over time is breaking wires in these harnesses.

• 
  @shahabnasrolahy239420 күн бұрын

  ♥ Thank You ♥

• 
  @machdaddy645120 күн бұрын

  Question. When I look up 2013 Escape fuse panel it shows a totally different fuse panel? They are the little push in type fuses, instead of the terminal inline fuse?

• 
  @BrianMann21620 күн бұрын

  I find that using the owners manual for fuse block location and fuse identification on ford to work best so times. Motorcraftservice.com has the owner manual for free.

• 
  @machdaddy645118 күн бұрын

  @@BrianMann216 Thanks. I didn't get a chance to help the women, before she took it to a dealer. Burned up some wires and some sensor. $2900

• 
  @machdaddy645120 күн бұрын

  This seems to be a very common problem.

• 
  @devonharmon194721 күн бұрын

  Thank you

• 
  @rossanderson768921 күн бұрын

  2018 Yukon Denali with P257D code. I just did the component test on the installed hood latch. Open and closed the reading was in the 700s. I bought a new latch today and it is the same. Am I missing something?

• 
  @78Arturin22 күн бұрын

  Thank you so much Sir ! This is the only video on KZread I've seen about this issue I had already replaced lots of things on my 2013 Malibu This High pressure pump video of yours saved me God bless you! And once again thank you so much! Greetings from Tijuana México ✌✌

• 
  @FMWheels26 күн бұрын

  I have a Mercedes c300 with a crank no start, it does detect rpm but no injector pulse, and intermittent spark. Seems like the same problem, but it doesn't run with the intake or exhaust sensors unplugged.

• 
  @Tysautoservice26 күн бұрын

  Are you using a vcmll connector or just a data cable from the laptop to the car?

• 
  @arubanjames26 күн бұрын

  I have this code. My 2018 Silverado LT 4.3L V6 4x4 crew. With 119,900 has been amazing. No problems. Except I have had to remove and clean the hood latch switch several times, about every other year, it seems now it is so mad it is showing my engine light…