@@劳永康 about 165psi. It’s still a fresh build so it’ll only get more compression the more I use it
@劳永康4 күн бұрын
11.5 20P Cleaverpropeller?
@codemang36355 күн бұрын
I can't believe you were able to scooch up front like that and actually save it. Made it look easy. Looks like a refined technique, from experience.
@damianburbidge23715 күн бұрын
Lots and lots of near misses. Weirdly enough the more it happens the more predictable the boat is.
@RoggerLemes8 күн бұрын
I'm thinking about a propeller. How much diameter would your 20P have? I'm not sure whether to put it at 11, 11.5, maybe 12. What diameter would I have to place a LWP...
@damianburbidge23718 күн бұрын
@@RoggerLemes hey mate. This is a 11.5 diameter. All really depends on what kind of power your engine has. Most of the guys here in Australia are running either a 11 or 11.5 on these engines
@thomaslindroos166710 күн бұрын
What kind of ridiculous port timing are you running
@christiaanmoikahk964614 күн бұрын
That helmet is not going to help you when things go south. Get a helmet with a open chin to avoid the bucket effect
@damianburbidge237113 күн бұрын
@@christiaanmoikahk9646 good idea
@MX-fo2nu20 күн бұрын
Cool and risky
@damianburbidge237120 күн бұрын
@@MX-fo2nu that’s why I’m called captain risky 😂
@user-rm9yg7kn1b26 күн бұрын
Как лодка называется?
@damianburbidge237126 күн бұрын
по английски пожалуйста. я невозможно скопировать ваше сообщение для перевода
@Pohuipliashem21 күн бұрын
@@damianburbidge2371 Could you provide information about the boat itself, as well as a link to the manufacturer's store for this boat?
@damianburbidge237120 күн бұрын
Thundercat
@user-rm9yg7kn1b20 күн бұрын
@@damianburbidge2371 ок, super.
@squidwould49113 күн бұрын
What prop are U guys running?
@jamesroberts1655Ай бұрын
Jesus.. you doing this shit in a balloon boat too!
@cottonsoxx1677Ай бұрын
Holy cow... Talk about balls to the wall. I wonder what he saw to his right and behind him that caused him to slow down so suddenly
@damianburbidge2371Ай бұрын
Hey mate. I used to run a hose from my engine to the side so I could monitor if the engine is pumping water or not and it had stopped 😅
@cottonsoxx1677Ай бұрын
@@damianburbidge2371 Ah yes... the all important telltale (not sure if that's what you guys call it over there?). Quite important when idling and at low throttle, but at when max throttle for so long, absolutely critical. Why used to though..? I've never seen it here, but it's a good idea.
@damianburbidge2371Ай бұрын
@@cottonsoxx1677 if you notice I’m Trying to keep the front down as much as possible and I need to concentrate on what’s going on in front of me. I can’t turn around and look at the engine at that speed. It’s just too dangerous. Think of it as another safety feature
@Checkmate858Ай бұрын
Awesome. everytime I try to get to your speed, you even go faster. Best I got so far is 103-104 with the 50 tohatsu. Have ran a LOT of props now but I nver would have guessed a 21G would perform this good. Ran a 19P 11" cleaver from MTM which is great for top but the holeshot is wayyyy to slow to be competitive. How is the holeshot with this prop if I may ask? Will get my 17P 11" cleaver with quite some rake this week I hope.
@damianburbidge2371Ай бұрын
103-104 is still good though. There’s a lot of boats out there that haven’t even hit 100 km/hr. It’s very slow out of the hole. It should be a bit better once it has been modified but this run was mainly for data to see where it can be improved. Keep at it mate !
@Checkmate858Ай бұрын
@@damianburbidge2371 you telling me you are running a stock engine here?
@damianburbidge2371Ай бұрын
@@Checkmate858 nooooo lol absolutely not. I was referring to modifying the cleaver.
@Checkmate858Ай бұрын
@@damianburbidge2371 running 12.2+bar compression. Dual stage Reeds, ported, chokes gone, smaller injectors, no limiter etc and still no luck for me.
@damianburbidge2371Ай бұрын
@@Checkmate858 where are you located ?
@Jeremy-ts4xpАй бұрын
👀🔥🔥🔥
@user-uj4jx5cy7kАй бұрын
Cool! What does overgassing do?
@damianburbidge2371Ай бұрын
Hey mate, are you referring to how I am controlling the throttle ? If so then I do it to stop the bow from coming up too high and causing it to flip. It’s a new cleaver which needs more modifying so it can be more stable at high speeds.
@user-uj4jx5cy7kАй бұрын
@@damianburbidge2371 Yes, I meant working with gas on the tiller. I thought that these transitions to lower speeds, add traction, and then speed.
@damianburbidge237116 сағат бұрын
@@user-uj4jx5cy7kyes and no. Sorry for the late reply. This boat is incredibly light and very sensitive to wind coming under the bow so the throttle needs adjusting as I drive.
@user-uj4jx5cy7k5 сағат бұрын
@@damianburbidge2371 Thanks!
@user-uj4jx5cy7kАй бұрын
What is the pitch of the propeller? And how many blades?
@damianburbidge2371Ай бұрын
18” cleaver 3
@user-uj4jx5cy7kАй бұрын
@@damianburbidge2371 18 х 0,0254 m = 0,457 m, 113 000 m/hr : 60= 1883,33 m/min, 1883,33 m :0,457 m = 4121 propeller shaft revolutions per minute!!! What is the engine crankshaft speed in this case?😲
@damianburbidge2371Ай бұрын
@@user-uj4jx5cy7k not sure how you come up with that. My rpm tacho is around 7500 RPM mark.
@user-uj4jx5cy7kАй бұрын
@@damianburbidge2371 I did not come up with it, but calculated it mathematically, according to the speed and pitch of the screw. But you still have increased engine speed. How do you deal with this phenomenon? A special fuel mixture?
@user-uj4jx5cy7kАй бұрын
@@damianburbidge2371 English is not my native language, and I did not study it at school. There may be difficulties with translation.☺
@user-uj4jx5cy7kАй бұрын
What is the pitch of the propeller? And how many blades?
@damianburbidge2371Ай бұрын
22“ cleaver. 3 blades
@user-uj4jx5cy7kАй бұрын
@@damianburbidge2371 Then what is the engine crankshaft speed?
@RoggerLemes8 күн бұрын
@@damianburbidge2371 I'm thinking about a propeller. How much diameter would your 20P have?
@damianburbidge23718 күн бұрын
@@RoggerLemes sorry this one was a 22 and the diameter was 12
@nunomascarenhasribeiro2 ай бұрын
crazy shitzzz
@damianburbidge23712 ай бұрын
This is the slow video haha
@nunomascarenhasribeiro2 ай бұрын
@@damianburbidge2371 would love to ride one of this cats…nothing similar in Europe. I like Tohatsu engines very much. Best 2 strokes ever.
@damianburbidge23712 ай бұрын
@@nunomascarenhasribeiro they are a lot of fun
@nunomascarenhasribeiroАй бұрын
@@damianburbidge2371 do you know if they are in Europe somewhere to buy?
@russoley89953 ай бұрын
looks fake to me
@damianburbidge23713 ай бұрын
Always a hater. ✌️
@lesliefigueras2183Ай бұрын
A friend of mine has the record for top speed on a thundercat with a modified d2 50 he hit about 120 kph
@damianburbidge2371Ай бұрын
@@lesliefigueras2183 I have have gone faster. I uploaded a video recently
@lesliefigueras2183Ай бұрын
@@damianburbidge2371 my mate did with a co pilot
@damianburbidge2371Ай бұрын
@@lesliefigueras2183 love to see the video.
@Checkmate8583 ай бұрын
Awesome run/ great save. (Accidently deleted my other reaction sorry) Gonna up my engine some more and take it for a spin with the 20P 👍
@quelincutajar82418 ай бұрын
Wath is that rmp and speed app pls
@damianburbidge2371Ай бұрын
Sorry didn’t see this comment. It’s a Garmin virb camera.
@nathanl779510 ай бұрын
That ain't no snowmobile. 😅 Thunder cat.
@dodern Жыл бұрын
Can i ask what kind of prop ?
@damianburbidge2371Ай бұрын
20 “ cleaver.
@user-xr5gu1rq6f Жыл бұрын
Looks durable and sporty. Very presentable and ready to go!! The boat looks safe too
@suadhalilovic1501 Жыл бұрын
Get £u¢ked, no £u¢ken way lol
@jsjrspivey Жыл бұрын
That's so badass ! I got to get one
@ryankolt7341 Жыл бұрын
what brand and pitch prop are you running ? what hole you have the trim rod in ? i just got my thudercat and trying to get it adjusted .
@damianburbidge2371 Жыл бұрын
porting, lightened flywheel , shaved heads , carbon fibre reeds, bigger fuel jets. Low water pickup gearbox 20” cleaver Ron hill ( thinned & added cup) Approx 55-58 mm off the transom 2nd hole. This is on a infanta thundercat, so transoms do vary depending on what brand you have.
@14josetomas Жыл бұрын
@@damianburbidge2371 this is great info. How much did you shave the head and what’s the bigger jet size? Boyesen o carson reeds? Appreciate your help!
@damianburbidge2371 Жыл бұрын
Boyson reeds yep , fuel jets 1.4 mm and the head had about .5 shaved off
@14josetomas Жыл бұрын
@@damianburbidge2371 awesome thanks, 0.5mm right?
@damianburbidge2371 Жыл бұрын
Yeah mate, I only did that because I couldn’t get my hands on a TSR head, but if you can get one I’d recommend getting one 👍
@reynierescandellhernandez79562 жыл бұрын
Amigo que tipo de balsa es y que motor ?
@damianburbidge2371Ай бұрын
50hp tohatsu Thundercat
@manuelmanuel10632 жыл бұрын
Krasse Nummer… super Leistungsgewicht. 👍
@leonardof38232 жыл бұрын
I have the same engine, but in an aluminum boat. What simple mod do you recommend to gain speed?
@damianburbidge23712 жыл бұрын
Bigger prop
@johnnymarx31582 жыл бұрын
What’s done to the motor an what prop are you using?
Пікірлер
How much pressure will he have with the TSR head?
@@劳永康 about 165psi. It’s still a fresh build so it’ll only get more compression the more I use it
11.5 20P Cleaverpropeller?
I can't believe you were able to scooch up front like that and actually save it. Made it look easy. Looks like a refined technique, from experience.
Lots and lots of near misses. Weirdly enough the more it happens the more predictable the boat is.
I'm thinking about a propeller. How much diameter would your 20P have? I'm not sure whether to put it at 11, 11.5, maybe 12. What diameter would I have to place a LWP...
@@RoggerLemes hey mate. This is a 11.5 diameter. All really depends on what kind of power your engine has. Most of the guys here in Australia are running either a 11 or 11.5 on these engines
What kind of ridiculous port timing are you running
That helmet is not going to help you when things go south. Get a helmet with a open chin to avoid the bucket effect
@@christiaanmoikahk9646 good idea
Cool and risky
@@MX-fo2nu that’s why I’m called captain risky 😂
Как лодка называется?
по английски пожалуйста. я невозможно скопировать ваше сообщение для перевода
@@damianburbidge2371 Could you provide information about the boat itself, as well as a link to the manufacturer's store for this boat?
Thundercat
@@damianburbidge2371 ок, super.
What prop are U guys running?
Jesus.. you doing this shit in a balloon boat too!
Holy cow... Talk about balls to the wall. I wonder what he saw to his right and behind him that caused him to slow down so suddenly
Hey mate. I used to run a hose from my engine to the side so I could monitor if the engine is pumping water or not and it had stopped 😅
@@damianburbidge2371 Ah yes... the all important telltale (not sure if that's what you guys call it over there?). Quite important when idling and at low throttle, but at when max throttle for so long, absolutely critical. Why used to though..? I've never seen it here, but it's a good idea.
@@cottonsoxx1677 if you notice I’m Trying to keep the front down as much as possible and I need to concentrate on what’s going on in front of me. I can’t turn around and look at the engine at that speed. It’s just too dangerous. Think of it as another safety feature
Awesome. everytime I try to get to your speed, you even go faster. Best I got so far is 103-104 with the 50 tohatsu. Have ran a LOT of props now but I nver would have guessed a 21G would perform this good. Ran a 19P 11" cleaver from MTM which is great for top but the holeshot is wayyyy to slow to be competitive. How is the holeshot with this prop if I may ask? Will get my 17P 11" cleaver with quite some rake this week I hope.
103-104 is still good though. There’s a lot of boats out there that haven’t even hit 100 km/hr. It’s very slow out of the hole. It should be a bit better once it has been modified but this run was mainly for data to see where it can be improved. Keep at it mate !
@@damianburbidge2371 you telling me you are running a stock engine here?
@@Checkmate858 nooooo lol absolutely not. I was referring to modifying the cleaver.
@@damianburbidge2371 running 12.2+bar compression. Dual stage Reeds, ported, chokes gone, smaller injectors, no limiter etc and still no luck for me.
@@Checkmate858 where are you located ?
👀🔥🔥🔥
Cool! What does overgassing do?
Hey mate, are you referring to how I am controlling the throttle ? If so then I do it to stop the bow from coming up too high and causing it to flip. It’s a new cleaver which needs more modifying so it can be more stable at high speeds.
@@damianburbidge2371 Yes, I meant working with gas on the tiller. I thought that these transitions to lower speeds, add traction, and then speed.
@@user-uj4jx5cy7kyes and no. Sorry for the late reply. This boat is incredibly light and very sensitive to wind coming under the bow so the throttle needs adjusting as I drive.
@@damianburbidge2371 Thanks!
What is the pitch of the propeller? And how many blades?
18” cleaver 3
@@damianburbidge2371 18 х 0,0254 m = 0,457 m, 113 000 m/hr : 60= 1883,33 m/min, 1883,33 m :0,457 m = 4121 propeller shaft revolutions per minute!!! What is the engine crankshaft speed in this case?😲
@@user-uj4jx5cy7k not sure how you come up with that. My rpm tacho is around 7500 RPM mark.
@@damianburbidge2371 I did not come up with it, but calculated it mathematically, according to the speed and pitch of the screw. But you still have increased engine speed. How do you deal with this phenomenon? A special fuel mixture?
@@damianburbidge2371 English is not my native language, and I did not study it at school. There may be difficulties with translation.☺
What is the pitch of the propeller? And how many blades?
22“ cleaver. 3 blades
@@damianburbidge2371 Then what is the engine crankshaft speed?
@@damianburbidge2371 I'm thinking about a propeller. How much diameter would your 20P have?
@@RoggerLemes sorry this one was a 22 and the diameter was 12
crazy shitzzz
This is the slow video haha
@@damianburbidge2371 would love to ride one of this cats…nothing similar in Europe. I like Tohatsu engines very much. Best 2 strokes ever.
@@nunomascarenhasribeiro they are a lot of fun
@@damianburbidge2371 do you know if they are in Europe somewhere to buy?
looks fake to me
Always a hater. ✌️
A friend of mine has the record for top speed on a thundercat with a modified d2 50 he hit about 120 kph
@@lesliefigueras2183 I have have gone faster. I uploaded a video recently
@@damianburbidge2371 my mate did with a co pilot
@@lesliefigueras2183 love to see the video.
Awesome run/ great save. (Accidently deleted my other reaction sorry) Gonna up my engine some more and take it for a spin with the 20P 👍
Wath is that rmp and speed app pls
Sorry didn’t see this comment. It’s a Garmin virb camera.
That ain't no snowmobile. 😅 Thunder cat.
Can i ask what kind of prop ?
20 “ cleaver.
Looks durable and sporty. Very presentable and ready to go!! The boat looks safe too
Get £u¢ked, no £u¢ken way lol
That's so badass ! I got to get one
what brand and pitch prop are you running ? what hole you have the trim rod in ? i just got my thudercat and trying to get it adjusted .
porting, lightened flywheel , shaved heads , carbon fibre reeds, bigger fuel jets. Low water pickup gearbox 20” cleaver Ron hill ( thinned & added cup) Approx 55-58 mm off the transom 2nd hole. This is on a infanta thundercat, so transoms do vary depending on what brand you have.
@@damianburbidge2371 this is great info. How much did you shave the head and what’s the bigger jet size? Boyesen o carson reeds? Appreciate your help!
Boyson reeds yep , fuel jets 1.4 mm and the head had about .5 shaved off
@@damianburbidge2371 awesome thanks, 0.5mm right?
Yeah mate, I only did that because I couldn’t get my hands on a TSR head, but if you can get one I’d recommend getting one 👍
Amigo que tipo de balsa es y que motor ?
50hp tohatsu Thundercat
Krasse Nummer… super Leistungsgewicht. 👍
I have the same engine, but in an aluminum boat. What simple mod do you recommend to gain speed?
Bigger prop
What’s done to the motor an what prop are you using?
Porting, lightened flywheel , shaved heads , carbon fibre reeds. Low water pickup gearbox 20” cleaver
my dad has one almost identical to that one
Mantap
Imagine if you weren't strapped into that thing! Good bye
Is the engine modified?
Yes
And I love it))
Fkin insane))
110 in a rib hot dam that’s sketchy
That is a legit pull. What software do you use for that?
Garmin VIRB XE camera
What does the hull look like that this motor was propelling?
Try google
Первый раз такой троллинг вижу🤭
Мне кажется икар по той же причине разбился
По какой? Все ему мало было)
А кто-нибудь в шлеме пробовал плавать?)))
Is that English?
@@damianburbidge2371 Has anyone tried swimming in a helmet? You can drown.
Yes I’ve flipped and rolled it plenty of times
Fantastic
Это он РЫБУ ТРОЛЛИТ)))
What type of engine?
50hp Tohatsu 2 stroke
long or short shaft?@@damianburbidge2371
👍🤘💪
Why so close to that pole
Because I’m a ninja !!
@@damianburbidge2371 a few inches again you would if bin a flying ninja loll
Serious question- I’ve never piloted these: is the dingy even touching the water at speed, or is it ground effect hovering?
The only thing touching the water is the bottom of the low water pick up gearbox and the high jackers.
He needs to stay away from the water
Смертник хули
Were those train crossing signs you were passing? That's what the second one looked like
No it’s a marker