Do you happen to have the link to where you bought the internals for the turbo?
@Underdog_off-road8 күн бұрын
Why are you selling the thing?
@yoits50cal311 күн бұрын
Ski doo is king
@JimMacLean-o7y18 күн бұрын
What did you do to set up the primary clutch. What belt did you use . I have a 1k xp with an RX1, still playing with the primary it seems to launch to hard. You did a great job the Nytro RZR build . I am impressed.
@braapaholic16 күн бұрын
right now we are running the primary from the snowmobile engine and the secondary from the razor turbo. I modified the secondary on the turbo to fit the snowmobile belt. We are going to throw on a aftermarket primary because the snowmobile primary is bad so we haven't done any tuning to the clutches yet.
@briandomer329519 күн бұрын
We have atrail boss and the radiator did the same thing …have any advice the radiator is leaking and we are needing help on how to braze it as well. My husband thinks there’s no helping it. I just am sad cuz it’s a nice quad
@braapaholic16 күн бұрын
Sadly these parts aren't readily available anymore. Being an oil cooler it is hard to keep them sealed and a braise just probably won't do it. Your best bet is to locate an ATV junkyard and look for a used one that's what I had to do.
@jeffalleshouse978320 күн бұрын
Put a silver blue xc secondary spring get rid of the stock red spring cause it will make the power flat like taking off in 3rd gear.
@braapaholic16 күн бұрын
Thanks for the advice
@unclebilly135323 күн бұрын
Very simple kit. I installed this kit on my hd10. But it didn't seem complete. I had to cut some spacers on the upper side and lower side. It seemed sloppy without them. But i do like the simplicity of them. Fyi im running 30s in tires and also running zbroz shocks and that adds another 2". The car has completely different ride and look for tne better. Good luck with you build.
@boneheadsgarage_1324 күн бұрын
Two years later beat to hell, a bit scratched and foggy but still works solid.
@user-uh4kk4ns7l26 күн бұрын
I’m so tempted on buying it man I see it posted for $3,000 and it’s not far from me aswell that’s how I found you’re channel
@Finn-the-deer-killer17 күн бұрын
Same
@Finn-the-deer-killer17 күн бұрын
But I don't want to buy it
@michael-zc7hoАй бұрын
All you got is the wheel fell off because you were negligent and didn’t put a cotter pin in like you’re supposed to and then you ran out of gas and then you need the valves adjusted
@masonwolf-ql2rzАй бұрын
i might buy this thing i saw it on face book
@phoenixarizona8441Ай бұрын
Had a 78 jag 440 for years
@randysavage6898Ай бұрын
The tire didn’t fall off because the machine is garbage 😂
@billapplegate6750Ай бұрын
I have a 2024 yxzrss. The worst thing ever made. Especially were I live in East TN.
@isaiahwalker7367Ай бұрын
Do you need license for this?
@BlockchainToTheFaceАй бұрын
I know this video is a couple years old but. Before and while you’re trying to cold start ANY Carbureted bike get on it and rock it side to side pretty good 3 or 4 times. It will crank a lot sooner. Especially on bikes that are a little hard to crank.
@larrywarren1049Ай бұрын
Was there access to the rear lower fender pieces without having to remove the inner fender once u raised the bed?
@onskuponsku_11eo212 ай бұрын
WHAT GEARBOX
@franciscocerritos46132 ай бұрын
That dnr agent is a tool
@cgaddy172 ай бұрын
Sc1 would shine the plastics of y’all’s bikes and sxs’s
@benjaminderousse32972 ай бұрын
Yank the bars harder and she might lift the skis boys. Once there hey
@benjaminderousse32972 ай бұрын
Oh my. A downhill😮
@benjaminderousse32972 ай бұрын
Ditch banging in a field
@benjaminderousse32972 ай бұрын
2o bucks on ebay. Can't believe it didn't work. 😂
@quinnlesley102 ай бұрын
Yes thank Justin. Hello from northern Indiana. And heck ya I’ll come ride with you guys
@caseymac20142 ай бұрын
Where were you riding at?
@braapaholic2 ай бұрын
Baldwin area. Lake City county
@SwaggyMcSwaggypants2 ай бұрын
L camera man
@braapaholic2 ай бұрын
Thanks I know. Many awards coming this way
@adamhoffman99652 ай бұрын
I came here because I saw your FB marketplace add. 😂
@braapaholic2 ай бұрын
Woot!
@stickytoy120728 күн бұрын
Me to
@triplthr2 ай бұрын
Unmatched camera skills lol
@tannerhoward46932 ай бұрын
LARRY !!!!
@michi_danksta2 ай бұрын
Hope your friend is okay. He seems pretty reckless.
@floridarednecks50612 ай бұрын
What size motor is it
@dylanbrantley1262 ай бұрын
I need one of these. I watch y’all’s videos all the time and wish I had the skills to build one.
@jasonparks52552 ай бұрын
Hey man love the vids. I'm from East TN literally 10 mins from tackett Creek and Royal blue and about 20mins from wind rock you guys should come down and ride
@KamKeim2 ай бұрын
I seen this on Facebook marketplace
@boneheadsgarage_132 ай бұрын
Love it 🤘
@matty82723 ай бұрын
My 2021 3 pedal is a real clutch.
@cameronwilliams10763 ай бұрын
You were riding it way too hard
@sir_tate13293 ай бұрын
Smell the belt while riding or no?
@milanvocati76133 ай бұрын
My xp turbo 2016 has the same problem. It is 600 hours and after it warmed up strange noises started. On the way back home Crashed the whole engine and broke the case. I want to rebuild the engine Replace everything with a new, except the engine head which is fine Recommend rev6?
@braapaholic3 ай бұрын
Stay away from rev 6. Nothing but headaches with them
@farmyardfab3 ай бұрын
So basically a LT YXZ Only worse.
@NorthernDispatch09433 ай бұрын
Awesome video!
@michaelgmcauliffe3 ай бұрын
skidoo all the way but i guess you got what you got !! Skidoo is number 1 for a reason
@jayfng3 ай бұрын
can you demo the app?
@denathornburg92543 ай бұрын
So satisfying
@user-gf5jw7ej8t3 ай бұрын
Been running mine straight pipes the last 3 years no problems at all didn't even need to do jetting also that yellow button is for reverse bc theres a revlimiter backing up 😊
@5to9fishing63 ай бұрын
How’d u hook it up
@norcoredneck3 ай бұрын
Does the display show what equalizer setting your in?
@milanvocati76134 ай бұрын
What year the RZR? I blow my engine in xp turbo 2016 need some tips
@braapaholic4 ай бұрын
It was a 2020. Do not buy a rebuild kit from rev6 power. If you don't know what you're doing, it's best to buy a reman engine and send your core back to them. Just swap it out and go. Otherwise you do need to buy special tools to put the engine back together
@Flawdagsxr1k4 ай бұрын
I watched this whole video if you pull the plug and it’s wet and the quads not hitting to start you have no spark then you follow that trail. You did a compression test if it in spec let’s say (50-60psi for example you will be allowed a 21 psi drop) that’s an example obviously see the owners manual. So you tore it apart several times for no reason in my opinion in which you probably came to the conclusion of one of two things off timing or no spark.
Пікірлер
Do you happen to have the link to where you bought the internals for the turbo?
Why are you selling the thing?
Ski doo is king
What did you do to set up the primary clutch. What belt did you use . I have a 1k xp with an RX1, still playing with the primary it seems to launch to hard. You did a great job the Nytro RZR build . I am impressed.
right now we are running the primary from the snowmobile engine and the secondary from the razor turbo. I modified the secondary on the turbo to fit the snowmobile belt. We are going to throw on a aftermarket primary because the snowmobile primary is bad so we haven't done any tuning to the clutches yet.
We have atrail boss and the radiator did the same thing …have any advice the radiator is leaking and we are needing help on how to braze it as well. My husband thinks there’s no helping it. I just am sad cuz it’s a nice quad
Sadly these parts aren't readily available anymore. Being an oil cooler it is hard to keep them sealed and a braise just probably won't do it. Your best bet is to locate an ATV junkyard and look for a used one that's what I had to do.
Put a silver blue xc secondary spring get rid of the stock red spring cause it will make the power flat like taking off in 3rd gear.
Thanks for the advice
Very simple kit. I installed this kit on my hd10. But it didn't seem complete. I had to cut some spacers on the upper side and lower side. It seemed sloppy without them. But i do like the simplicity of them. Fyi im running 30s in tires and also running zbroz shocks and that adds another 2". The car has completely different ride and look for tne better. Good luck with you build.
Two years later beat to hell, a bit scratched and foggy but still works solid.
I’m so tempted on buying it man I see it posted for $3,000 and it’s not far from me aswell that’s how I found you’re channel
Same
But I don't want to buy it
All you got is the wheel fell off because you were negligent and didn’t put a cotter pin in like you’re supposed to and then you ran out of gas and then you need the valves adjusted
i might buy this thing i saw it on face book
Had a 78 jag 440 for years
The tire didn’t fall off because the machine is garbage 😂
I have a 2024 yxzrss. The worst thing ever made. Especially were I live in East TN.
Do you need license for this?
I know this video is a couple years old but. Before and while you’re trying to cold start ANY Carbureted bike get on it and rock it side to side pretty good 3 or 4 times. It will crank a lot sooner. Especially on bikes that are a little hard to crank.
Was there access to the rear lower fender pieces without having to remove the inner fender once u raised the bed?
WHAT GEARBOX
That dnr agent is a tool
Sc1 would shine the plastics of y’all’s bikes and sxs’s
Yank the bars harder and she might lift the skis boys. Once there hey
Oh my. A downhill😮
Ditch banging in a field
2o bucks on ebay. Can't believe it didn't work. 😂
Yes thank Justin. Hello from northern Indiana. And heck ya I’ll come ride with you guys
Where were you riding at?
Baldwin area. Lake City county
L camera man
Thanks I know. Many awards coming this way
I came here because I saw your FB marketplace add. 😂
Woot!
Me to
Unmatched camera skills lol
LARRY !!!!
Hope your friend is okay. He seems pretty reckless.
What size motor is it
I need one of these. I watch y’all’s videos all the time and wish I had the skills to build one.
Hey man love the vids. I'm from East TN literally 10 mins from tackett Creek and Royal blue and about 20mins from wind rock you guys should come down and ride
I seen this on Facebook marketplace
Love it 🤘
My 2021 3 pedal is a real clutch.
You were riding it way too hard
Smell the belt while riding or no?
My xp turbo 2016 has the same problem. It is 600 hours and after it warmed up strange noises started. On the way back home Crashed the whole engine and broke the case. I want to rebuild the engine Replace everything with a new, except the engine head which is fine Recommend rev6?
Stay away from rev 6. Nothing but headaches with them
So basically a LT YXZ Only worse.
Awesome video!
skidoo all the way but i guess you got what you got !! Skidoo is number 1 for a reason
can you demo the app?
So satisfying
Been running mine straight pipes the last 3 years no problems at all didn't even need to do jetting also that yellow button is for reverse bc theres a revlimiter backing up 😊
How’d u hook it up
Does the display show what equalizer setting your in?
What year the RZR? I blow my engine in xp turbo 2016 need some tips
It was a 2020. Do not buy a rebuild kit from rev6 power. If you don't know what you're doing, it's best to buy a reman engine and send your core back to them. Just swap it out and go. Otherwise you do need to buy special tools to put the engine back together
I watched this whole video if you pull the plug and it’s wet and the quads not hitting to start you have no spark then you follow that trail. You did a compression test if it in spec let’s say (50-60psi for example you will be allowed a 21 psi drop) that’s an example obviously see the owners manual. So you tore it apart several times for no reason in my opinion in which you probably came to the conclusion of one of two things off timing or no spark.
Watch part 2