Пікірлер

• 
  @DirtyWizardCustoms3 күн бұрын

  DirtChop FTW🤙🤙🤙

• 
  @SocialMisfits3 күн бұрын

  Lexmoto vixen exhausts would work for your twin exhaust setup

• 
  @maheshrajamuni90875 күн бұрын

  Its really 😮

• 
  @alanyeo882922 күн бұрын

  terrible camera work makes me dizzy

• 
  @CultofRust21 күн бұрын

  Yeah you're right...hopefully I've got better. Thanks for watching

• 
  @markb989629 күн бұрын

  🤯

• 
  @HondacxcaferacerАй бұрын

  Also I have found CMSL and there exploded diagrams essential for seeking part numbers and checking cross compatibility between old Honda’s.

• 
  @CultofRust29 күн бұрын

  I recently found them too great page. Thanks for your help bud

• 
  @HondacxcaferacerАй бұрын

  Mate, you need to get Larry Cargill’s carb book. For CX/GL500s but the carbs are the same.

• 
  @CultofRust29 күн бұрын

  Cheers man I'll have a look

• 
  @kevbaldwin9552Ай бұрын

  Try a bit of Pink stuff keep it wet and soak it for an hour or two then autosol .i have had some success using this and it dosent scratch the chrome

• 
  @CultofRustАй бұрын

  Thankyou I will that. Thanks for watching

• 
  @DirtyWizardCustomsАй бұрын

  Bro, proxl do a really really good reusable rust remover!

• 
  @CultofRustАй бұрын

  Cheers man. I will look into it

• 
  @cerealtillerАй бұрын

  Is it the Camera lens or are the Front Forks slightly bent?

• 
  @CultofRustАй бұрын

  It's probably the camera settings...Still figuring out new gopro. Forks are fine. Thanks for watching

• 
  @blissisland7680Ай бұрын

  Informative and entertaining at the same time, great, keep up the good work.

• 
  @CultofRustАй бұрын

  Thankyou so much

• 
  @DirtyWizardCustomsАй бұрын

  Fuck yeah!!!

• 
  @neiljones4677Ай бұрын

  Love the light 🔺and the noise! Good looking bike.

• 
  @scrinjaАй бұрын

  You should of put the level on the action NOT the Woodwork Dude ?

• 
  @cerealtillerАй бұрын

  I fitted a Motad to my GL1200...the way to make a louder but Mellow Drone from the Tail Pipes was to Extend them the sound is good now and heard by other Traffic .....but not at nuisance levels Resonance works better than just high Volume good Video thank you .

• 
  @CultofRustАй бұрын

  Thanks for watching

• 
  @LJenkinsEsqIIIАй бұрын

  I have the opposite problem. Old torch has 2 wires, new one has 1 wire

• 
  @rosswitte2 ай бұрын

  Outstanding!!! Mind blown how simple and how genius this is. Thank you!

• 
  @CultofRustАй бұрын

  Thankyou. Glad it helps

• 
  @Workforaliving2 ай бұрын

  Very good. never seen it done that way before. be the perfect way to tune you scope bubble I will diffidently try it. Thank you

• 
  @CultofRustАй бұрын

  Thankyou

• 
  @Roko8392 ай бұрын

  Can you wash it with domestos?

• 
  @CultofRustАй бұрын

  I honestly don't know sorry

• 
  @CCP_Automotive_Group2 ай бұрын

  Big fuckin allen

• 
  @wm.traynor11433 ай бұрын

  Clever👍👍😄😄

• 
  @Baikal19713 ай бұрын

  i think im going to need a proper gun vice

• 
  @turkeygaming58513 ай бұрын

  Hey man, ive been watching your videos with the jinlun JL 125-11 to see if you had anything in there about the timing as i think mine is out, when i rev the bike they climb really slow and if i ride the bike i cant get above 30mph even in third gear. Any advice on what i need to do to fix the issue would be much appreciated

• 
  @CultofRust2 ай бұрын

  Have you made any changes like pod filters to the system?

• 
  @turkeygaming58512 ай бұрын

  @@CultofRust no, the bike is all standard. The only thing that has been changed is the gasket

• 
  @turkeygaming58513 ай бұрын

  I've had a Jinlun for a while now but only recently had the gasket replaced, im not sure if the issue I've currently got is a timing issue and if it is how do i set the timing? The issue im having is my revs are climbing really slow, and I can't go above 30mph even in 3rd gear

• 
  @markrhodes54743 ай бұрын

  Brilliant 👍

• 
  @Ronracer3 ай бұрын

  Your face without the cans 😂😂😂

• 
  @CultofRust2 ай бұрын

  It's amazing

• 
  @chrisdevitto43403 ай бұрын

  That’s toilet bowl cleaner, curved top, which uses a very mild acid.

• 
  @johnfiore93903 ай бұрын

  Plumb line to expensive just a bolt with some of nans wool😂

• 
  @CultofRust3 ай бұрын

  Hey if it works dude....gravity is still free lol

• 
  @johnfiore93903 ай бұрын

  @CultofRust agreed ha 😆 🤣

• 
  @TheStigma3 ай бұрын

  WARNING: Asssuming that I looked up the right datasheet then this product is NOT bleach, but actually HCL acid-based (and that makes sense that it would help remove rust). Bleach on the other hand is a strong oxidizer, and it will heavily speed up oxidation (rusting) on all metals because it releases a lot of oxygen as it reacts. Putting actual bleach (sodium hypoclorite) on a metal part like this would probably be a disaster. I had to look it up because these results made no sense if it was bleach. I assume the author was just confused by the labeling and didn't have malicious intent.

• 
  @CultofRust3 ай бұрын

  Thankyou for your advice. I didn't mean to mislead anyone with this video and the product. This product was sold to me as bleach and I was truly ignorant until your post. Definitely no malicious intent on my part. Thankyou for leaving advice and not abuse.

• 
  @TheStigma3 ай бұрын

  @@CultofRust No problem. Everyone makes mistakes. Any bleach based product will have sodium hypochlorite on the ingredients label if in doubt. Most acids will help dissolve rust, and you can probably find a much better source for acid than this stuff which is fairly dilute. Products for de-calcifying concrete (building/home improvement) are often sold in bulk 5L for cheap and usually contain hydrochloric or phosphoric acid. Just check the ingredients label. Cleaning vinegar is also good and cheap, and citric acid may be found in reasonable quantitites as concentrated powder in food stores and supermarkets are it's used for pickling. After any acid rust removal you should neutralize the acid with a base (a little baking soda in water), dry off, and then either paint or oil as soon as possible. Otherwise it will "flash rust" and start to show visible surface rust again in as little as a few hours (depending on humidity). Any acid left on the surface makes the flash rusting happen even faster - so that's why neutralizing is important - or at least a very thorough rinse.

• 
  @TexasEngineer3 ай бұрын

  I am glad you tried bleach. I would never recommend bleach with steel. Bleach causes steel to rust. Soap and water might be as effective, don’t know. To get rid of rust you need an acid like vinegar or muriatic acid. Either way you have to neutralize your chemicals afterwards.

• 
  @TheStigma3 ай бұрын

  I looked up the datasheet for the product, and it's HCL acid based, not bleach. That makes a lot more sense with the results. The video title should really be changed to avoid people trying to replicate this with actual bleach.

• 
  @CultofRust3 ай бұрын

  Thankyou for drawing my attention to this. I was honestly unaware of differences till you pointed this out. Thankyou for your advice.

• 
  @jakevipond39383 ай бұрын

  Sounds better than I expected it to. Very nice

• 
  @dannytacoboi40144 ай бұрын

  What did you all do to make it sound like that?

• 
  @CultofRust4 ай бұрын

  Hi I will be uploading a full video of the modified project. Please like and subscribe. Thanks for watching

• 
  @orvallhall3244 ай бұрын

  Man, thanks so much for this video. I have the same single black wire setup as you. I bought my new torch from Yes Welder which had 2 wires in a connector. My old welder is a Due Mig made in Italy. No one from Yes Welder tech support knows what to do to hook their whip to a single wire setup. If you wouldn't mind telling me where the white wire with the spade connection that you attached the pink wire to is attached on the other end, that would be great. I wonder if it is on the wire speed dial. Also does it matter which of the two wires attach to the places that you put them? Once again, thank you for making the video. Orvall

• 
  @CultofRust4 ай бұрын

  Thankyou for watching. I believe the wire went to speed control but I have since sold this unit and purchased a new one so I'm unable to check.

• 
  @orvallhall3244 ай бұрын

  Wow, thanks for getting back to me. I figured it out, trial and error with your video. Great chatting with you. Cheers my friend.

• 
  @CultofRust4 ай бұрын

  @@orvallhall324 that's awesome. Sorry it took me so long. Enjoy and be safe

• 
  @Joeyfingis4 ай бұрын

  Great video, I had the same problem but on my speedo side, unfortunately after a few times of adding graphite it started wearing out the speedo cable almost monthly. I had to get a replacement gauge.

• 
  @CultofRust4 ай бұрын

  Thankyou for watching. I'm hoping this lasts...its been good for about 250 miles so far.... fingers crossed

• 
  @johnfiore93904 ай бұрын

  I ay even got a first stage on mine so i will be drying this out. Thanks

• 
  @CultofRust4 ай бұрын

  Hope this helps. Thankyou

• 
  @peterdarlington41175 ай бұрын

  Bro said all you need is a torch! I got super excited and brought in my oxygen acetylene rig my wife was like what are you doing with your torch in the kitchen? I said I don’t know I’ll tell you when the British guy tells me! Was super let down!!!!!!

• 
  @CultofRust5 ай бұрын

  I hope you managed to find a use for the torch until you get a "flashlight"

• 
  @niazali46875 ай бұрын

  Super cheap and DIY Ultimate video I found on KZread For gas tank rust removal and rust proofing 👇👇👇 m.kzread.info/dash/bejne/mZ-mmJiHeKanfsY.html

• 
  @chirpy9995 ай бұрын

  Good film, just picked one up not running yet ,missing a recoil starter and the pieces of the head that hold the tank on are damaged so cover wont fit properly. Got another engine and few more mowers to get a recoil starter off.

• 
  @CultofRust5 ай бұрын

  Good luck my friend. Thanks for watching

• 
  @jimlowis18785 ай бұрын

  Thanks mate.

• 
  @CultofRust5 ай бұрын

  Glad it helped

• 
  @bishfishinuk26765 ай бұрын

  Awesome content keep up the good work

• 
  @superblackhawk6 ай бұрын

  Am I to assume the NP03 is the same?

• 
  @CultofRust6 ай бұрын

  I think so

• 
  @RCBELtd6 ай бұрын

  It was a great scamble. them bumpy bits on the grass straight were fun

• 
  @CultofRust6 ай бұрын

  It was awesome. Can't wait till next year

• 
  @icanseeyouallfromuphere6 ай бұрын

  So the bleach work just got rid of a lot more muck, so I realised I have a carton of brick acid, so poured it in the tank, about 3 hours ago, it's gradually working to bare metal, in bits, it's a 9.5% HCL

• 
  @CultofRust6 ай бұрын

  awesome. hope it works for you

• 
  @icanseeyouallfromuphere6 ай бұрын

  Yuh it's pretty much bare steel from about 7 hours of the brick acid (9.5% Hydrochloric acid/HCL) just that's left is surface layers in the sides of the tank, I've got petrol soaking in it over night and adjitating it with bolts and a door chain slung in....I will probably mix in a whole pot of metal polish with the petrol tomorrow as I know that will erode rust particles from steel aswell, that should be about that, for a last rinse out I'll order some white vinegar Monday. ✌🏻

• 
  @icanseeyouallfromuphere6 ай бұрын

  , in fact as it would amount, in theory if you had a metal polish dilution, that should amount a as good / better / same as result, better in the essence that it also treats the metal for longevity

• 
  @CultofRust6 ай бұрын

  worth a thought. thankyou

• 
  @icanseeyouallfromuphere6 ай бұрын

  😂 i have a '78 CB200 am doing up, I left the bike in the garden when I wasn't very well and got it in before all the rain last winter, chassis survived, oil still in motor so no bottom end rust (haven't got the head off yet) but the tank cap was left open and was a tad worse than yours .....so i uh, watching this thought hang on I've got a litre of bleach and half a litre of stainless steel/ kitchen cleaner 💡! So shoved the lot in the tank , topped it to the brim with water, shook the hell out of it, stuck it on its side (old petcock leaks and drops out the cap but it'll be okay for 24hours, tomorrow here we come 😂

• 
  @CultofRust6 ай бұрын

  awesome. Good luck

• 
  @michaelmroczek73606 ай бұрын

  whats exhaust are you running on it? sounds like a dream

• 
  @CultofRust6 ай бұрын

  it's a danmoto. gonna be honest I was given it for free

• 
  @JasonNeal-wu3sj7 ай бұрын

  By beginning with a spirit level on the gun to level the gun itself, this flashlight approach will produce a proper reticle-to-bore alignment if and only if both the gun and the scope rings are mechanically perfect across about a half dozen potential sources of error. In other words, in most cases it will likely be better than eyeballing it but don't trust it to yield near-perfect alignment.

• 
  @maxwebster75727 ай бұрын

  You need to be DAMN SURE nobody mixes anything in with that acid or bleach. While they are calling it bleach I don't recall bleach removing limescale. Somebody may mix bleach in and create mustard gas. I googled it quick and one post is saying that product hydrochloric acid.

• 
  @CultofRust6 ай бұрын

  thanks for the heads up

• 
  @DeepakMishra-dj6ms7 ай бұрын

  English ko gooli Maro Hindi mein samjhawo 😅😅😅😅😅😅😅😅😅😅😅😅😅😅😅

• 
  @CultofRust3 ай бұрын

  I have no idea what this means sorry

• 
  @markflew39567 ай бұрын

  I'm thinking about doing my full licence as just got my cbt in April but don't know if to stick to the 125 or go on and train up for big boy licence and do it

• 
  @CultofRust7 ай бұрын

  Man if you're happy on 125 then stay as you are... just enjoy it

• 
  @Sun_TzuayАй бұрын

  You can still get a big boy license on a 125, only if you are 24 year and older if thay helps, or progressive access, pain in the ass but same results to a full license. Good luck