This helped me replace my cable eight years later. Thank you
@LaVeriteSurToutEtSurtout-vu2nu23 күн бұрын
Super car
@albertocastro53897 ай бұрын
No se engrasan los cables con el tiempo eso endurece
@HelloHello-hk4sx7 ай бұрын
Kissing a child on his lips? 😳
@eatonjask Жыл бұрын
The Crossfire was the most amazing product to come out of Daimler-Chrysler - it was even available with a Mercedes AMG supercharged engine!
@natebeach Жыл бұрын
God, I remember this and the Crossover commercial!... I'd get goosebumps when the music would kick in.
@lilnightmare47 Жыл бұрын
Just done mine with help from your video thanks so much guys the G clamp helps so much 😂
@ErosAxiom Жыл бұрын
This was a great video. The repair manual doesn’t say to use a clamp to hold the clutch lever up, and I couldn’t get enough slack to connect the other end to the hand lever. Watched this, got a clamp, and voilà!!! Thank you. My motorcycle would still be sitting in the parking lot of the shopping mall if you hadn’t made this video!! IOU
@emmettturner9452 Жыл бұрын
You should remove the clutch cable from the clutch lever at the handlebars before you remove it from the arm going into the clutch itself. You only needed the clamp because you did not give yourself the slack needed from the other end.
@captain_morgan_official Жыл бұрын
I was lookin for this comment before i said it. 😅
@josephferris69362 жыл бұрын
Dont use wd40 for that its not the right stuff for that job
@ericschermerhorn34872 жыл бұрын
anyone know if this is the same for an 06?
@petergiourelas37532 жыл бұрын
Great car
@suraramtahal86182 жыл бұрын
Saw in other vids..not to use wd40
@filoIII2 жыл бұрын
I can't get it out of the handle for 2 yrs now.
@stylo8845 Жыл бұрын
Still trying?
@filoIII Жыл бұрын
@@stylo8845 I gave up.
@ritmolatino1627 Жыл бұрын
use a grinder to get the job done
@luisg71092 жыл бұрын
Who would think in 2021 all cars would look like the unsuccessful Pacifica from 2003🤨
@yk682 жыл бұрын
MY EAR
@natemcg89942 жыл бұрын
Going to be doing this on my 2008 maybe tmrw thanks for the vid
@robinsmith19702 жыл бұрын
I never saw these commercials in 2011but I'm watching now on my phone aus2021
@johnweber803 жыл бұрын
I had something similar happen to me on the Xbox. I was driving the Mercedes CLK GTR and instantly flew up entering a shortcut and almost did a full 360 before landing and getting stuck for a moment.
@quicksand40893 жыл бұрын
This is five years old but very relevant. Even better is a girl working/helping work on a bike is a true rarity and turn on.
@promitey23733 жыл бұрын
Моя первая семейная тачка, много с связано с этой машиной.
@vacuumlover13 жыл бұрын
NO ONE CAN BLOW A HEAD GASKET THE WAY THAT YOU DO
@roycewilliams60613 жыл бұрын
Thank You Thank You Thank You!!! What an informative video. You just save me a trip to the shop and money.
@berberykopl3 жыл бұрын
0:21 xd
@JRodzTv3 жыл бұрын
Cool vid
@SGK23TV3 жыл бұрын
How did you get the cable like that? Miles? Slipping? Or some factory issues? Thanx! Ride safe.
@emmettturner9452 Жыл бұрын
Happened to me. Actually snapped… probably because I never lubed it.
@HelloHello-hk4sx3 жыл бұрын
0:04 That's probably how fast she'd really drive, on the highway or city. 😅 She fucka hyper.
@tientrinh9433 жыл бұрын
I love chrysler
@AntonioSilva-ce7cl3 жыл бұрын
The world wasn't ready for Chrysler Pacifica
@andrewn.caldwell62183 жыл бұрын
For real, nowadays everyone drives that bland Subaru Forester
@elijahtorres26885 ай бұрын
Chrysler now has the potential to sell crossovers… they’re just only focusing on the Pacifica minivans now, after they done discontinued the 300.
@droomkoning32664 ай бұрын
Facts@@elijahtorres2688
@iluvcamaros19122 ай бұрын
It was nice but it had horrid reliability issues. And it was pricey. I don't know for sure but I'd guess if you could afford a new Pacifica it wouldn't have been a stretch to buy a Lexus RX or an Acura.
@nathancollins58223 жыл бұрын
I would make a VIDEO of the things that you did that you should have not done. However, ty for trying to help ppl...
@BikeLifeMike933 жыл бұрын
Hey did you pull it through the circular hole, or go underneath it? Having a hard time following that part when putting in a new cable.
@yo_stephen3 жыл бұрын
Wonderful in depth video. Thank you
@syfiltzo4 жыл бұрын
No need for clamp if you unset from lever first. The angle in lower clutch adjustment is wrong, you are much over 90 degrees. Check you manual..
@justinlyons86764 жыл бұрын
the tachometer and speedometer hasn't go full sweep 😕the gas gauge and temp gauge did ok but not the tachometer and speedometer
@abdulahsan78514 жыл бұрын
How long do you do it?
@mohdnizamhezmimohdnizamhez64654 жыл бұрын
Nice bike..
@JamesAutoDude4 жыл бұрын
That's so cool!
@cjiekel6684 жыл бұрын
0:13
@rodwellsimon42795 жыл бұрын
I love Celine #Queen
@thequietstorm895 жыл бұрын
Main reason I love Chrysler, when I was younger seeing this commercial of my idol Celine Dion I fell in love with this minivan. Still drive my 2002 touring T&C. ❤❤❤
@quocphu015 жыл бұрын
My wife hands are tiny and sore after a long ride using the clutch so I will turn into hydraulic on eBay.com $40 buck kit, haven’t fit it yet, the customs kit cost $700 lol, wish me luck
@JohnRoX5 жыл бұрын
Good way to save money
@KJ3Reaction5 жыл бұрын
Thanks for the vid! I have to replace my cable and this will save me a trip to the shop!
@angus_americas5 жыл бұрын
Question! What happens if you don't put oil in the cable???
@2ndAznBum5 жыл бұрын
It's more-less for the longevity of the cable. Nothing bad will happen short term, but it might wear out faster over time.
@emmettturner9452 Жыл бұрын
It eventually frays like the original did. It’s supposed to be lubricated regularly. They sell special tools with cans of “cable lube” specifically for doing it while it’s on the bike.
@robertmcginty41466 жыл бұрын
Thanks for the advice. Clutch cable on my Honda Shadow snapped completely off while going 50 mph in traffic, going to go attempt this now.
@robertsmith39676 жыл бұрын
Thank you for your instruction. Nice to hear a lady's voice. Diesel is good for lubricating cables. Just soak the cable in diesel.
@frankdenardo86846 жыл бұрын
Celine Dion is Canadian this van was built in Windsor Ontario.
@toddrandolph246 жыл бұрын
this is another good video,kzread.info/dash/bejne/dqqHp81pnru_mLQ.html do not use WD40 as a lubricant in any application; for this motor oil will work fine.
@davem53336 жыл бұрын
Am doing the clutch cable on a 07 Ninja 250. Son's bike. Clutch grab point was almost at full release and real tricky in city traffic. Both end adjusters were all the way out. Difficult to shift, especially when cold. Bike itself is the coldest blooded thing I ever encountered. It's an 07, so a lot of that has to do with EPA compliance. Watched the video and it helped a lot. As for disconnecting the lower ferule from the throw-out lever, the C_clamp didn't work for me. Wrong size clamp. Found that if you just cut the lower cable boot, drop the lower nut off the cable end, you can get enough slack to disengage the cable from the throw-out lever. On removal cable showed no fray and was smooth. Must have been stretched out.
@davem53336 жыл бұрын
Good video. But don't make the clutch release too low or you will be dragging your throw out bearing. Also you need enough bite so the clutch fully disengages between shifts or you can wear out your synchros.
Пікірлер
This helped me replace my cable eight years later. Thank you
Super car
No se engrasan los cables con el tiempo eso endurece
Kissing a child on his lips? 😳
The Crossfire was the most amazing product to come out of Daimler-Chrysler - it was even available with a Mercedes AMG supercharged engine!
God, I remember this and the Crossover commercial!... I'd get goosebumps when the music would kick in.
Just done mine with help from your video thanks so much guys the G clamp helps so much 😂
This was a great video. The repair manual doesn’t say to use a clamp to hold the clutch lever up, and I couldn’t get enough slack to connect the other end to the hand lever. Watched this, got a clamp, and voilà!!! Thank you. My motorcycle would still be sitting in the parking lot of the shopping mall if you hadn’t made this video!! IOU
You should remove the clutch cable from the clutch lever at the handlebars before you remove it from the arm going into the clutch itself. You only needed the clamp because you did not give yourself the slack needed from the other end.
I was lookin for this comment before i said it. 😅
Dont use wd40 for that its not the right stuff for that job
anyone know if this is the same for an 06?
Great car
Saw in other vids..not to use wd40
I can't get it out of the handle for 2 yrs now.
Still trying?
@@stylo8845 I gave up.
use a grinder to get the job done
Who would think in 2021 all cars would look like the unsuccessful Pacifica from 2003🤨
MY EAR
Going to be doing this on my 2008 maybe tmrw thanks for the vid
I never saw these commercials in 2011but I'm watching now on my phone aus2021
I had something similar happen to me on the Xbox. I was driving the Mercedes CLK GTR and instantly flew up entering a shortcut and almost did a full 360 before landing and getting stuck for a moment.
This is five years old but very relevant. Even better is a girl working/helping work on a bike is a true rarity and turn on.
Моя первая семейная тачка, много с связано с этой машиной.
NO ONE CAN BLOW A HEAD GASKET THE WAY THAT YOU DO
Thank You Thank You Thank You!!! What an informative video. You just save me a trip to the shop and money.
0:21 xd
Cool vid
How did you get the cable like that? Miles? Slipping? Or some factory issues? Thanx! Ride safe.
Happened to me. Actually snapped… probably because I never lubed it.
0:04 That's probably how fast she'd really drive, on the highway or city. 😅 She fucka hyper.
I love chrysler
The world wasn't ready for Chrysler Pacifica
For real, nowadays everyone drives that bland Subaru Forester
Chrysler now has the potential to sell crossovers… they’re just only focusing on the Pacifica minivans now, after they done discontinued the 300.
Facts@@elijahtorres2688
It was nice but it had horrid reliability issues. And it was pricey. I don't know for sure but I'd guess if you could afford a new Pacifica it wouldn't have been a stretch to buy a Lexus RX or an Acura.
I would make a VIDEO of the things that you did that you should have not done. However, ty for trying to help ppl...
Hey did you pull it through the circular hole, or go underneath it? Having a hard time following that part when putting in a new cable.
Wonderful in depth video. Thank you
No need for clamp if you unset from lever first. The angle in lower clutch adjustment is wrong, you are much over 90 degrees. Check you manual..
the tachometer and speedometer hasn't go full sweep 😕the gas gauge and temp gauge did ok but not the tachometer and speedometer
How long do you do it?
Nice bike..
That's so cool!
0:13
I love Celine #Queen
Main reason I love Chrysler, when I was younger seeing this commercial of my idol Celine Dion I fell in love with this minivan. Still drive my 2002 touring T&C. ❤❤❤
My wife hands are tiny and sore after a long ride using the clutch so I will turn into hydraulic on eBay.com $40 buck kit, haven’t fit it yet, the customs kit cost $700 lol, wish me luck
Good way to save money
Thanks for the vid! I have to replace my cable and this will save me a trip to the shop!
Question! What happens if you don't put oil in the cable???
It's more-less for the longevity of the cable. Nothing bad will happen short term, but it might wear out faster over time.
It eventually frays like the original did. It’s supposed to be lubricated regularly. They sell special tools with cans of “cable lube” specifically for doing it while it’s on the bike.
Thanks for the advice. Clutch cable on my Honda Shadow snapped completely off while going 50 mph in traffic, going to go attempt this now.
Thank you for your instruction. Nice to hear a lady's voice. Diesel is good for lubricating cables. Just soak the cable in diesel.
Celine Dion is Canadian this van was built in Windsor Ontario.
this is another good video,kzread.info/dash/bejne/dqqHp81pnru_mLQ.html do not use WD40 as a lubricant in any application; for this motor oil will work fine.
Am doing the clutch cable on a 07 Ninja 250. Son's bike. Clutch grab point was almost at full release and real tricky in city traffic. Both end adjusters were all the way out. Difficult to shift, especially when cold. Bike itself is the coldest blooded thing I ever encountered. It's an 07, so a lot of that has to do with EPA compliance. Watched the video and it helped a lot. As for disconnecting the lower ferule from the throw-out lever, the C_clamp didn't work for me. Wrong size clamp. Found that if you just cut the lower cable boot, drop the lower nut off the cable end, you can get enough slack to disengage the cable from the throw-out lever. On removal cable showed no fray and was smooth. Must have been stretched out.
Good video. But don't make the clutch release too low or you will be dragging your throw out bearing. Also you need enough bite so the clutch fully disengages between shifts or you can wear out your synchros.