Пікірлер

• 
  @MrAirtaz17 күн бұрын

  if anyone is attempting to do this with the AllTop Twin Cylinder compressor, the 1/8" to 1/8" extender is way too small for that hole. Apparently all of these compressors aren't the same with different names.

• 
  @jp-go7hgАй бұрын

  You sir are a legend. Many people have videos on this but your setup is the simplest. A lot of people add jumper cables

• 
  @jp-go7hg25 күн бұрын

  update: "new" napa model comes with built in switch

• 
  @johnf12962 ай бұрын

  ❤❤

• 
  @davidsharp35222 ай бұрын

  Oetiker clamps

• 
  @MrCarmelo19594 ай бұрын

  Awesome setup thanks for sharing I need to make one also configure it to use with my semi truck 10 tires it would be great again thanks again

• 
  @geriatricginger4 ай бұрын

  These compressors are now black, and NAPA-branded. I just picked one up for $122.

• 
  @toobusyagain4 ай бұрын

  The end caps are NOT meant to be removed. Just slide the insert back toward the center, lift up and pull out. Install the same way in reverse. Not sure how he got the end caps off but they are meant to be fixed.

• 
  @obrnc09204 ай бұрын

  When it rains this car is SO dangerous. Damn thing hydroplanes on me. I try not to drive at all. Thankfully I’m in Cali

• 
  @WooleySwampAdventures5 ай бұрын

  The factory unit has a pressure relief switch built into the inline gauge which you deleted, I'm not sure if I just missed it, but where did you put it on yours as it's a very important safety item? Thanks

• 
  @johnphillipsjr72386 ай бұрын

  Just bypass that board.

• 
  @nhitc68326 ай бұрын

  you're right about the OEM blades. They don't last as long as you'd think. My just completely broke in pieces. Had to order aftermarket that are made out of silicone.

• 
  @js89826 ай бұрын

  I totally agree with the analog gauge vs digital. not convenient to deal with dead or corroded batteries

• 
  @sleeks99394 ай бұрын

  I put electric grease on my battery for my digital gauge and haven’t had a problem

• 
  @69sins6 ай бұрын

  If you have a clay bar kit or one you didnt fully use, spray some lubricant on the windshield and use the clay bar on the windshield. Then use a ceramic coating on it and it'll keep your windshield nice and clean for a good while

• 
  @HardscapePro7 ай бұрын

  Cutting those red wires right from the middle was a big mistake I have seen other videos And what they did they use a different method

• 
  @1kontrabida7 ай бұрын

  Make sure the thread sealant is completely dry before testing it, also u can use a silicon caulk instead of the thread sealant just make its dry before using it. ALuminum manifolds are good but they tend to leak at times specially if u over tight the fittings, due softer nature of aluminum they tend to expand and or crack.

• 
  @salazarsalazar65987 ай бұрын

  Wow sir great job tremendous explanation and great attitude your a rock star my good guy thanks I’m doing exactly what your explaining wow A+

• 
  @jerrybarrax56187 ай бұрын

  Thanks for posting!

• 
  @abecoulter85508 ай бұрын

  rather than cutting the wire from the back of the switch, why not unplug the connector and put it on the pressure switch?

• 
  @irwinjimenez9 ай бұрын

  Great write up. I bought all the parts you suggested. I really appreciated your follow up Update as well. Any new updates?

• 
  @ttss572610 ай бұрын

  All that to fill tires. Just do one at a time and call it a day this is just lazy

• 
  @chublez10 ай бұрын

  I'd probably just unplug the wire from the factory switch and use that lead to one side of the pressure switch then make a new lead for the other...no butt connectors needed. If the wires to short I'd desolder it and start fresh...less failure points. I'm likely going to gar a bit further and ditch the board and wimpy power leads in favor of a big relay.

• 
  @Easy270511 ай бұрын

  I have a fj60 stock and my alternator is kinda crappy now it’s the original one. Would this alternator be a good upgrade from stock??

• 
  @thegiant57311 ай бұрын

  So did you get another ine or fix that one?

• 
  @eyygurke608111 ай бұрын

  Functionally operates just as it should kzread.infoUgkxiiMg_x4gIWeXMWfBnDdRnME4qJUAva4w holds pressure perfectly when not in use. Glad one of the other reviews pointed out that the bottom pressure release valve was open; thought it was defective at first.

• 
  @Smokeroux Жыл бұрын

  Thanks for this video!!! New Subscriber🏁

• 
  @johnmadsen37 Жыл бұрын

  Those metal clips always wear out the weak metal threads on the valve stems. A clip on right angle rubber type is actually better. Psi matters more when airing down. The difference between 14 and 15 psi doesn’t matter but 6 and 5 psi can be a serious issue. Especially deep snow 5 and 4 psi.

• 
  @AntonioClaudioMichael Жыл бұрын

  Very good mod Wish you could still get these maxi Trac compressors

• 
  @davecarter34 Жыл бұрын

  I really wanted to make one, I already use flexible for the pressure cleaner and my single air hose, after pricing up the parts I found the TUFF TERRAIN MULTI TYRE DEFLATOR KIT (4 VALVE) is priced at 96usd or 149 aud, parts are price here in Australia

• 
  @lonelydriver82 Жыл бұрын

  Sounds like a great deal and easy decision!

• 
  @Eduardo-mg7zm Жыл бұрын

  🙈 Promo-SM

• 
  @happyravishankar Жыл бұрын

  I got the same error initially that prk assiat is not available when Iam prking in garage and sode wall is 2-3ft away. It also says side pillar cam is blocked and park assist unavailable. Now a days it says aide pillar cam is blocked and prk assist degraded. I still do not get the inches when park assist is degraded or earlier park assist not available. Tesla replaced side camera but still the same issue. Iam on 2023.12.5 no USS 2023 M3LR

• 
  @TheSprul85 Жыл бұрын

  I own a Toyota land cruiser bj60 wagon... Everything is standard and now its 39 years old... Just got issue with the electrical output... Should i upgrade the altenator or just upgrade all wiring that connect to the altenator?

• 
  @nicholaswerbeck8424 Жыл бұрын

  Built one for myself based on your design. So glad did. Thanks for sharing

• 
  @lonelydriver82 Жыл бұрын

  awesome! glad this was helpful!

• 
  @samhartfieldlewis5247 Жыл бұрын

  Really smart system, thanks

• 
  @reidmartin3479 Жыл бұрын

  Great video! Did you have any recommendations on other manifolds to get?

• 
  @lonelydriver82 Жыл бұрын

  I'd look into the brass ones not as cool looking but should seal better

• 
  @jayvilla5985 Жыл бұрын

  Let’s be honest. If you bought a new car without the sensors you should be pissed. We were all screwed. And we all need to get together and show Tesla/Elon we’re pissed, otherwise he’ll keep taking advantage of us. Stop being super fans. They will not get better if we’re not 100% honest. The new vision update IDEA is cool, but in reality it’s TRASH. This is all the best of the best engineers could do in 6 months? It’s not going to get much better. Not with the current hardware. And retrofitting will not be an option, so we’re screwed. I suggest selling your Tesla now before HW4 is released.

• 
  @gerritvandendool133 Жыл бұрын

  Not ready? No, not at alll, and I am afraid it will never get ready anymore. After all, if this is the best Tesla engineers can come up with, I am no longer optimistic about further improvements, given they themselves no doubt have already done the same (disappointing) tests as the ones shown here and elsewhere. It remains just impossible to guess in a reliable way what is on blind spots that are not covered by a camera.

• 
  @multiwebtechnologies Жыл бұрын

  Nice shoes 😁

• 
  @shortshortscoin3473 Жыл бұрын

  Vision-only is a fool’s errand. Anyone relying on vision-only is doomed!😇

• 
  @gamedesigner2421 Жыл бұрын

  Malfunction because of the crocs😄

• 
  @spyro440 Жыл бұрын

  My old Ford Focus from 2015 just does this with a few ultrasonic sensors and it completely reliable, doesn't matter if it's raining, if bright day or night. Why Tesla, why.

• 
  @SuBros760 Жыл бұрын

  Probably because it’s too dark and the cameras are geeking out with the lighting or/and humidity… my car is bad too. Didn’t expect anything less after the removal of the sensors though.

• 
  @user-dt8hh9ni4r Жыл бұрын

  seems to be doing fine in traditional parking spaces but not in weird parking situations like yours which seems reasonable for the first release

• 
  @tonyturu9400 Жыл бұрын

  everything is good tesla fanboy very very reasonable loll

• 
  @Sammy0003 Жыл бұрын

  We should I know how park etc It’s driving basics 101 🤦‍♂️ Coming from a MYP owner

• 
  @TheKnyght123 Жыл бұрын

  2 things 1) Eyeballing it to claim the distance is wrong is not an appropriate way to disprove whether something is correct or not. 2) The front camera is notoriously the one with the most reported issues in 100% accurate distance. It'd be better to show distances from sides, and rear as well to get a good idea if it's working as intended.

• 
  @lonelydriver82 Жыл бұрын

  Read the description, I measured it

• 
  @PMitchell106 Жыл бұрын

  Serious question, is there anyone in the automotive industry who offers a parking assist system that is worse than this?

• 
  @mubashir3 Жыл бұрын

  The old sensors could see things in front that were low to the ground. Can the cameras cover that area?

• 
  @jackylsmith8138 Жыл бұрын

  Currently no. Tesla is supposed to have a new low bumper cam on the updated model 3 soon.

• 
  @ladenree31 Жыл бұрын

  What happens when the rear camera is blocked by water?

• 
  @rasberry4739 Жыл бұрын

  Does everyone get this feature. Or do you need autopilot

• 
  @DiscoveryOwners Жыл бұрын

  USS on my MY don’t work a whole lot better, certainly can’t trust it for getting close. Just give me a Birds Eye view like other less expensive cars have. No Birds Eye/360 view, no RCTA, not even rear AEB. No ventilated seats. And I took a $20k hit on depreciation. After 6 months of ownership, not a happy owner.

• 
  @B.ENGERGY Жыл бұрын

  Hey, I think this works quite nice for the beginning. Also appreciate that you see what's left and right from the car! Could finally work better than USS solutions.